Kembali ke atas

DMR-JAPAN

DMR-JAPAN adalah spesialis modifikasi motor balap dua-tak lama seperti NS400R, NSR, dan lain-lain. DMR-JAPAN menyediakan berbagai part mulai dari saklar stang hingga sparepart rem dan mesin untuk mengembalikan motor kesayangan Anda ke kondisi yang prima.

3.9
(8 Ulasan)

5

Sangat Baik

3

4

Baik

3

3

Sedang

0

2

Buruk

2

1

Sangat Buruk

0

Produk Baru DMR-JAPAN

Ulasan Produk DMR-JAPAN

The caliper looks terrible quality casting marks and damage painted over. The paint is coming off and I have only handle the caliper for 5 minutes. The slide dust covers are very low quality and where installed incorrectly on arrival. The banjo fitting seat is damaged from side. Picture advertised says hissin but it is cheap poor quality. 190mm disc seems ok and also the master cylinder seems ok

I bought a reputable DMR made in Net reviews.
It is quiet and nice as described! It was cheap so I was a little worried but it seems good to make it solid.
The Gold genus made by a company that I used before was bothering meow and sounds, and the Coat which I expected was also torn off.
It seems to be higher quality than OEM? We are looking forward to the durability of MCNylon!

I installed it to ns 1 which Bore up to 63 cc. It is a braking force, but it is a Level where there is no problem in city riding. I tried suddenly Brake from a state where the speed was out so far, but I was not particularly dissatisfied.
I changed Pad, so I do not know how much change is due to disc change only ...
I think that it looks good, so I think that it is good as Dress-up parts.

As Minus surface, I thought that it was rust prevention, but it was a bit chilly with oil. What I did first after it arrived was to drop this oil.
There was also a regular BALI in disc for Front.
Well, it was a problem Level, but it is a place to worry about. For Rear has no BALI at all, so I am more concerned.

I wrote because there was no Review.
I'm glad if you can use it as a reference.

I use it with XR 100 MOTARD, but it got brighter than I imagined. You can see clearly that OEM's light distribution is not good.
Installation is easy, but I think that some ingenuity is required. Socket and Waterproof Cover should better use OEM (It is usable normally). Apart from Reflector, it was made quite reasonable.
I think that it is inexpensive against the effect. LEDs and HID will also be brighter.

I purchased the odor of OEMLens with Lens cut to manage it.

According to other reviews, Position lampWaterproofRubber is already loose at the time of arrival - The terminal of the contact part with the Valve of the PH7's Socket is disconnected, there is considerable difficulty in fitting etc. etc. , I decided not to buy it by paying 4000 yen.

As a result I bought Lens with a warehouse and OEM brand new item.
Compared to Lens which was blurred with Yellow for years, the new item is cheap as it is a little 2000 yen at Beauty to fluffy.. I wish I had made OEM brand new from the beginning.

Hi all, This headlight lamp is a great alternative to the OEM unit, great quality and finish, Fits perfectly. I would highly recommend this item.

* I attached it to my friend's KSR. It is a representation of my friend.

【What made you decide the purchase?】
Light was quite dark

【How was it actually used?】
It got pretty bright
Use Valve included

【Was it difficult to install? (Hard parts case)】
I scraped a little light cowl

【Please tell me the point of installation and hang (in the case of Hard parts)】
If the drip-proof Cover? Is an OEM, a gap can be formed, so remove the LightConnector,
Set the attached Cover finally

Do not be afraid to do it carefully Large durable

[Is there anything I was disappointed about?]
When Position bulb socket wears on Multi-reflector, it goes through with a throat.

【Hope for Manufacturer - Please let me know if there are any improvement points】 Required
Outside diameter of Position bulb socket? Precision of hole of Multi-reflector.

【Have you compared items?】 Required
LED Light

[Others] Any

I will add it if my friend says something.

Light of the off-road motorcycle, especially the old car of 90`s is dark! But LEDs and HID are Battery reply vehicles .... Also, Wiring processing and Included Parts : I also have to secure a mounting location for. What a person Recommends here!
Wiring just connects like an OEM! Cat's-eye just branches off from Low beam and just takes it away. (It disappears at the time of High beam)
It got brighter, it's about +1 mass from the torch of dragon Quest. (Oops! It is hard for a young person to understand?
The difficulty is that Rubber of Cat's-eye falls into polo-polo and falls out without permission, so so-called booger Bond (G17) Lightly point with.
Also, although it may be only yourself, the optical axis is facing upwards, especially on the Right! It is like turning the face of the opposing pedestrian battlely.
Since it is impossible to adjust with Adjustment Screw, paste Rubber on Cowl's contact surface and fix it.
It is easy to install and we are holding down the price, so it seems worth it!