Kembali ke atas

K-CON

K-CON adalah brand lini produk mounting kit universal dari KITACO. K-CON menawarkan mounting kit seperti baut, collar, mur dan sekrup dengan harga terjangkau.

4.2
(659 Ulasan)

5

Sangat Baik

298

4

Baik

216

3

Sedang

110

2

Buruk

26

1

Sangat Buruk

9

Produk Baru K-CON

Ulasan Produk K-CON

Fits perfectly for my extra fuel cock on dax st70, easy to install i like the bend part so it can slip on any bolt without changing the mounting position, recommended for you who are looking for a simple bracket, will be ordering again for my other motorcyle, thanks Webike and K-Con

It purchased as an output side of the oil cooler of an ape.
If it is those who understand the location in which a hole is made, and a size, it can be perfectly used by OK.

It is small and is an L type oil nipple 90 degrees.
It is used for extension of the breather nipple of the engine of 4mini.
Since extraction of a breather is made to a smart and it is easy to adjust the extraction angle of a hose, it is recommended very well.
They are parts which can be dramatically used considering a price.

It can be exactly used for the output side of the oil cooler of an ape.

The ape 50 was equipped as output port of an oil cooler.
The goods themselves are made very finely and there was neither a bali nor a wound.
I think that such a little thing will lead to a manufacturer's reliance.
I think how it is that takes no less than 500 yen to this product.
Although the tapped hole was cut and attached to the clutch cover, I got it to be safer to give a pro the direction where processing of drilling etc. is diffident.
I think that it will succeed if it is processed by itself, and it takes care about the following three points.
- Put the mark on the place which punctures to a punch correctly.
- Change the drill into the thick thing gradually.
Like [ of 1 mm -> 2 mm -> 4 mm -> 6.7 mm ].
- Use cutting oil, when using drilling and a tap, and carry out slowly.
I think that it will succeed if it takes care about these.
If it practices, I will think that it is better.

It is used for the circumference of the crankcase of the monkey.
Brightness peculiar to a stainless is perfect for the generator cover of a takegawa.

It is perfect!!

If it says from [[in play part 2]] conclusion, the products here will be the highest products in general!!
The aluminum spacer collar here is inside diameter:phi8.2mm. Outside diameter: phi20mm Height: It becomes a 30-mm product.
If existence of Webike is not known Didn't it meet with the aluminum spacer collar made from a kitaco, and the vivid bolt?,
.
.
By Webike, customization filled to originality and creativity can be performed, and it is a delightful limitation!! An attached image,
The muffler made from p's supply is treated to the address V125, and it is a chamber protector made from burial. (tune by a moriwaki sticker and #OS800-30000-41!!) In order to equip,
They are contents which use the aluminum spacer collar made from a kitaco and vivid bolt which are the products chosen as the end of deliberation.
The spacer collar made from a product chamber protector made from burial 竊?kitaco.
(#0900-093-00060, inside diameter phi8.2mm, outside-diameter phi20mm, and 30 mm in height) The engine side of the product muffler made from product muffler made from 竊?p's supply attached aluminum billet plate 竊?p's supply attached M8 aluminum-collar (outside-diameter phi20 mm and, and 14 mm in height) 竊?address V125.
A muffler mount and M8 female-screw partial we the bolt used of this customization,
- vivid bolt made from a kitaco of M8x100 (#0900-080-0015) was chosen!! [ -- [refer to [ the in play part 1 ]] ], if two or more sets of the addresses V125 which drive the inside of a town are seen,
It seems that its respectively different customization was given and each loves the address V125 colored with personality.
Moreover, is conversion of a muffler mentioned the common feature of customization of the address V125?
.
.
If it equips with the chamber protector made from burial, how is it as a protector to the replace muffler which you chose (the outside diameter of a white duracon resin part is phi36mm.)?
The size of the sticker of a moriwaki is about 56 mm.
Since the outer circumference of a duracon part is about 113 mm, the sticker of a moriwaki is a size like the semicircle.
it is just a sticker tune of a just size!! Replace muffler of the address V125 which we incidentally cannot but praise, steiner muffler made from p's supply it is -- TSU!!