Kembali ke atas

STING R&D

STING R&D merancang dan memproduksi berbagai macam bodywork seperti spakbor depan dan belakang, fairing, dan masih banyak lainnya yang berbahan FRP dan carbon. STING R&D sudah memiliki segudang pengalaman sebagai pabrikan part OEM untuk manufaktur sepeda motor ternama sehingga produk-produknya tidak hanya memiliki tampilan yang apik, namun juga awet dipakai.

3.6
(23 Ulasan)

5

Sangat Baik

6

4

Baik

7

3

Sedang

6

2

Buruk

3

1

Sangat Buruk

1

Ulasan Produk STING R&D

I purchased it with reference to good evaluation of COSPA.
Quality is satisfying with price.
The texture of Carbon is beautiful.
However, when I installed it, something does not work. If you look closely well FenderBody has some distortion Quantity : Pair (for Left and Right) There was a difference of only a little less than Mounting Bolt of. Although wearing was possible as it was, it was not convinced, so I looked at it from the front Left Side Biting Spacer on Mounting Bolt Quantity : Pair (for Left and Right) Hitoshi etc. It was mounted at the height of. Result Calm down to the feeling that distortion does not matter. A person who needs Quality of OEM Product needs a little care.


I installed it in SOQIInverted Front Fork of XJR 1300
This inverted Fender has the same shape as carburetor R1
Cutting part of Fender support department
The rest is the same.

The product is thin and obviously lighter.
Some bubbles were contained. Because it is in a prominent place
It is a star 4.
Although the dimensional accuracy is reasonable
When relocating Rubber Bush from OEM
Even though it is thin and tightened with Bolt, it hits Gold color
Because Fender was rattled
Gold genus was cut by 5 millimeters.
Rubber Bush can be crushed and attached securely.

Products made by Sting R & D company are of course not only looks, but since the Gold amount of the buyer's eyes is set even among Motorcycle Parts Manufacturer who is circulating with a high price more than anything else, since Dress-up can be done without stretching up, the search ranking in the future I am thinking in 1st place. This time, I think that the purchased product is one item of Recommendation even if it looks comprehensively without the necessity of processing.

OEM Replacement Type, but the width and mounting hole position did not match. For width it is possible to install if it is prepared for deformation, but it is safe to put a thick RubberWasher or something in the gap between Body and Fork. I am one Side 5? (Quantity : Pair (for Left and Right) I wrote a Rubber Seat of 1?). Even this still has some margin (>_<). As soon as you set the taking hole as it is, it gently becomes an off car Fender Since the position became high, 2 on the F side and 2 on the R side. 5? I opened the hole upwards and managed somehow normal installation. Since the original size was adjusted, the original hole on the F side can see an elliptical shape that has been scraped, but now it is one so I will refresh the lower part of the Fender side as well (T_T) It is cheap and its shape is not bad with the OEM but it can be made a bit better ~ " (-""-) "

I compared it with OEM Product. Making itself is nice, but Quantity : Pair (for Left and Right) It is mandatory to rework with half finish as if being cut asymmetrically. Cut too much, or Cut finished halfway .... If you can not fix it yourself, please purchase OEM Product.

By saying "Other Company Product", it is clearly stated as two Nuts, but I hate direct Nut hitting Carbon fender, I removed Bracket from OEMFender and ported it perfectly to Front fork etc. etc. Despite being tightened to, the Tire clearance before and after is Quantity : Pair (for Left and Right) Asymmetrical and immediately removed.
I sent a wearing image and asked for a replacement but I am sorry to refuse Bassari when I can not exchange after processing.
Material : Carbon products are prepared to individual differences, but just spreading the mounting hole in the hole of OEMBracket has no reason to cause a whirlpiece, which is not unpleasant, but I will never buy it again. Those who buy it because it is cheap are advised to check with the Manufacturer recommended way of attaching and checking if there is a whirlpool and to put in Objection.

The OEM Fender installation part has broken and it is a replacement.
Although it is a translation to replace OEMFender when installing, OEM will interfere with Fork when removing. And it was possible to put in this product with little interference..
It is an impression that it is because it is thin with Carbon?.
Also in the OEMFender there is something like Stubby made of iron, I am addicted to the mounting hole from the back.. This item has good hole position precision, it is very convenient!
Fender Outside Material : The accuracy of the mounting hole of AluminumStubby is also naturally good, but there is a gap between Stubby and Fender. Even if you look closely at product pictures, there are gaps, so it's like this is not it!. I wanted you to be hooked as much as possible, but I guess it would be worthwhile considering the price ....
And AluminumStubby has a hole to catch at the rear center, but Fender has no hole. Also there are no mounting holes for parts to pass through the Meter cable, so you need to open a hole if you care. I just installed it, but it seems there is no problem in use.
Finally, there was also in other people 's impression, but when it hits the sun, parts that can be seen are seen there so much !! I became worried and painted with a matte black from the back and solved the sheer.
There are parts to worry about, but considering this price there is no problem at all !? (Lol)

Although it is an OEM Shape, there is no Light hole or Bracket
Screen mounting holes and Cowl mounting holes are merely open
Hole etc etc for competition vehicles. It seems to be just right as it seems to be unnecessary