Plus side : Price is cheap, around (grip) Soft, I think that it is good not to get stiff even in cold weather, individuals with many vibrations.
Minus surface : Grip becomes thick (About Grip heater included) So, for those who are Small in hands, depending on the angle of Handlebar, the thickness increases, Lever and Handlebar (Core of) There is a possibility that the thing may feel distant and it may be difficult to walk around so I think that the evaluation will break up.
Because my FUSION can not adjust the angle for Normal handle, I felt it slightly upward more than to Upright (Feeling holding down from above) became.
Because it is a Scooter which does not hold down even Positionally, the difference of several millimeters is sensuously pretty much Large.
Recommended for those who can adjust Handle position based on the thickness of Grip.
On the other hand, Direct feeling of Handlebar becomes thin, so I feel dull when I turn around.
เป็นปลอกแฮนด์ที่สวยมาก เนื้อวัสดุที่มีคุณภาพ การออกแบบที่ดี ขั้นตอนในการใส่เพียง 1-2 ขั้นตอนก็เรียบร้อย เหมาะกับการใช้งานที่หลากหลายทั้งทางใกล้และการเดินทางไกล ช่วยลดการสั่นสะเทือนในขณะขับขี่ กระชับเวลาเร่งคันเร่ง และสามารถทนต่อฝุ่นและน้ำโดยไม่ลื่นและเสื่อมสภาพ ผมใช้ในการเดินทางมากกว่า 500 กม ในครั้งเดียว และจะใช้ในการเดินทางไกลต่อไป It is a very handsome casing. Quality material Good design Step in just 1-2 steps to complete. Suitable for a wide range of applications both near and far. Reduces vibration while driving. Accelerated accelerator accelerator And can withstand dust and water without slipping and wear. I used to travel more than 500 km at one time and it is used to travel further. (translated by Google Translator)
【What made you decide the purchase?】 I thought that I would like to use Project mu's Brake Pads, so I bought it at the same time as Rotor exchange.
【How was it actually used?】 It's a nuffy and effective impression when you hold Lever. Nevertheless, smoothly, Linear, Brake fee with no sense of twist like OEM Ring Ring. I think it's wonderful.
【Was it difficult to install? (Hard parts case)】 Just remove the Caliper, wash it, install it after cleaning!
【Please tell me the point of installation and hang (in the case of Hard parts)】 Let's loosen Pad pinBolt first before loosening Caliper installation Bolt. If I do not do this, I do not need the force and I think that Pad pin is hard to remove.
【Fit feeling and height when wearing - Please tell me the weight etc (Apparel case) ]
[Is there anything I was disappointed about?] There is nothing in particular.. I do not know about durability yet.
【Hope for Manufacturer - Please let me know if there are any improvement points; because it comes with Carbon in the product name, it can not be used for CarbonRotor in the explanation column for Stainless rotor. May I have a note written in a word?.
【Have you compared items?】 It is Sintered by DAYTONA, but I quit immediately..
[Others] Let 's make exchange in the future to be around PRO mu!
Because of the 2nd decline in 30 years it was very bad for the engine to hang, and it took a 5-10 minutes on Kick start to take it for granted. Starting ability improved dramatically since wearing Iridium plugs (Within 2 minutes). I use Iridium plugs on 4th, but I never felt the difference with Normal plug. But I think that you can feel the price more than the price with 2st Kick start car.
S of CB 1000 SF. T. Purchase this Grip so DGrip is GETTA. Also purchased simultaneously for VTR 250. As long as you are familiar with the exchange, you can wear it without problems. Regarding CB 1000 SF, both grips are about 5 mm shorter as shown in the attached picture. The feeling attached was thicker than the OEM more than the OEM but the feel is nice. Afterwards it is a verification of durability to confirm operational feeling and fatigue feeling at Touring. If there is a problem with a short Grip, at that time Spaceretc. We plan to remodel. Although it is not attached to the VTR 250, since there is no problem with Length, I am going to judge the attachment after the test at CB.