Kembali ke atas

Comfortable grips...simple and nice. Good

Since oil change time came, it purchases in order to also exchange filters simultaneously.
I wanted red ....

I made this Filter the same as last time in the third Oil exchange.
Filter wrench is not required, there is no new expense, even in terms of performance
Since I could use it without problems, I would like to repeat it in the future.

Order these grips for a Honda CBR1000f as per the listing but they are to short,I should have measured the old grips instead of trusting the listing so please check before you order.Nice grip otherwise.

It is used for commuting everyday, and it has been installed for many years with Tank's scratch prevention.
It's thick and the surface slides considerably.
* Jeans x, leather Pants ○

HELLO I'M SATISFIED OF THIS PRODUCT. SO I NOTICED AROUND 5000 RPM ,THE ENGINE SEEMS LIKE TO HAVE BLOWS. AS IS AN RACING PLUG YOU HAVE TO MAINTAIN A CERTAIN POWER FOR AVOIDING BLOWS.UP 5000 RPM YOU HAVE GOOD SENSATIONS.

Oil leakage of Front fork for the first time in ninth year. SFK is the best Seal and I tried using it. I do not know the performance difference. Just feeling of security and superiority of Green Light is a consideration.

I thought that it could be cheap at with Magnet, purchased, nothing was Paint on the exterior It was good at Simple
Since the tightening Torque is stated in the OEM, I watched it and installed it, but the next time I need to look it up
MT07 was 15 Nm

Oil Filter is exchanged periodically, but performance is not problem at all.
Also, as long as it functions as a filter, Manufacturer thinks it is unnecessary to keep in mind.

I was using it in a parking without a roof, but when I removed Cover after rain, both the Motorcycle and the inside of the Cover were always in a condition wet.
Looking at the wetting way of Motorcycle, it seems that the whole is covered with moisture condensation rather than rain infiltrated,
When riding the next day of rain, we start with wiping up condensation on the car body.
Ventilation holes around the position of Handlebar do not work at all.
In the vicinity where the Exhaust System hits, the inside seems to be a heat-resistant material, but it began to be torn in about a year.
With this performance, durability, this price is too high.
quality - The three-dimensional star of texture is an evaluation of only the solid inner nonwoven fabric that covers the Upper Cowl from Screen.

2017 MT-09 Racer used with GIVISpecial rack SR 212 1 and Set.
Although it took time to understand the relationship between this case and Base, there was no problem as long as it was installed.
(For initial top case installation)
It seems possible to install another Size, but I chose it because it seems that the fit is more beautiful.

When we arrived, it was already floating from release paper.
It seemed that the adhesive strength was not 0 and the season was still hot, so I tried adhering to Tank in the meantime and then it will float after a while.
As another means, by holding down from above for a long time, I hope that the shape of Pad itself will become familiar with Tank, I will keep curing Tape from above and keep it familiar 2 months.
I thought that it would have become familiar with it and seemed to be sticking somewhat when removing the curing tape.
But. It floated on the next day.
If you leave it like this, you will scratch the painting of Tank if you get in dust, so you only have to peel off.
It is mere Large loss.

Feeling of use
As expected, it is sweeter than Bolt stoppage to Carrier, so if it is a box with a horizontal width, it will become more severe for the unbalance of luggage etc.
However, it is fixed more firmly than expected, and there is little wobble.
I am wearing a box named B 47 of GIVI, but I think that the box width up to about 30 L is about 40 cm, so I feel that the feeling of use does not change from the one fixed to the carrier.

About mounting
As this product is once taken BALI, I think that Seat will not be scratched immediately, but if it fixes, the Gold genus part will be strongly pressed against Seat, so long term use and heavy luggage etc If you post it probably Seat will be torn.
Also, since the width of the item is narrow, Belt for fixing also goes to Cowl
To be strongly pressed, Belt's rubbing measures are also necessary.

For the wounds of Seat I will fold the micro fiber toowel for washing for Vehicle for the time being.
We have not taken countermeasures concerning Belt's rubbing, but we plan to paste a scratch prevention Seat on the Cowl side.

I bought it because I need a Joint gasket for exhaust system replacement. There is no problem in mounting.

Gasket corresponding to Injection's VTR 250 "JPH-9" It's ProductNo so do not make a mistake.

* Carburetor cars and Injection cars have different Pipe diameters, so pay attention to that point as well!

How much iron powder etc on Magnet etc. I'm not sure whether it is adsorbed, but with Filter + Alpha this price has a sense of security and sense of security. We will continue to use it in the future.

'