Kembali ke atas

Comfortable grips...simple and nice. Good

Safe packaging, received perfectly, good quality, easy fitting. Installed on CB400SS without any issue

I made this Filter the same as last time in the third Oil exchange.
Filter wrench is not required, there is no new expense, even in terms of performance
Since I could use it without problems, I would like to repeat it in the future.

HELLO I'M SATISFIED OF THIS PRODUCT. SO I NOTICED AROUND 5000 RPM ,THE ENGINE SEEMS LIKE TO HAVE BLOWS. AS IS AN RACING PLUG YOU HAVE TO MAINTAIN A CERTAIN POWER FOR AVOIDING BLOWS.UP 5000 RPM YOU HAVE GOOD SENSATIONS.

Hello. I bought this oil filter for my Yamaha YZF R1 2005. The package was well packaged, came, without any damage. The oil filter HIFLOFILTRO HF-303 was designed easily and without problems. The quality of the goods is as high as it should be. I will buy more. I recommend it to everyone. Do not regret that you buy it for your favorite motorcycle. I wish everyone good luck and success. Thank you .

How much iron powder etc on Magnet etc. I'm not sure whether it is adsorbed, but with Filter + Alpha this price has a sense of security and sense of security. We will continue to use it in the future.

I exchanged Plug because it exceeded 11000 km. Although it is an impression of about 500 km,
The attachment of Axel at 1500-3000 rpm improved, and the high rotation also turned well
I think. 5 speed 40 km is easier to run. Just 2000-3000 Partial
I feel that the area became irritable, and it became difficult to maintain a little with. I want to increase the vibration...
Because the heat value is not matched, the original Plug may be more comfortable for regular rotation. I am worrying about returning..
Looking at you..

I will lend just as much as I grasped. There is nothing to eat at the beginning of grasping or getting up at the back.
There are various situations such as when you want to decelerate slowly, when you need to apply sudden braking, but you can control with the strength of grasping Lever. I do not seem to have any advantage, but I am surprised that the width of Control is flexible.
With more than a certain pace, you can manipulate Fork with Brake.

I bought it because the replacement of the Oil filter is approaching.
Since I bought it at Sale time, I am superior in Cost performance.
Recently I have been using this product all the time, especially the bad place
There is none. I will use it next time as well.

To be truthfully written - - - -
I do not know in a short time whether it is good for Engine
I do not get well.
Evaluation is difficult as long as problems do not occur.

I can not keep it, accuracy is poor and I can not install it
There is nothing wrong with the problem.

I am using it with Circuit, and Gymkhana.
Although it is not terribly effective it is terrible,
I think that it is an excellent Pad that you can Breaking exactly as you want.
Although I feel it is somewhat expensive, Stress Nothing about performance and reliability,
I think that it is also included.
Is not it enough because the decrease is not so early.

The shape of the tip is slightly different from OEM. I feel a sense of incompatibility when I put on Rubber cap.

Seal tape winds in the reverse direction, not in the tightening direction.

Noticing that Brake fluid seeped out of Caliper's Air breeder
Rust was amazing as I removed it. Indeed when I thought this was dangerous, I found this product
Replaced. As I wrote that the installation was to tighten Seal tape one half turn and tighten
I rolled Emon's Seal tape. It looks more modest to the ground.
If you think that you could buy safety cheaply in the long run as it will not rust.

By the way, by wrapping a Seal tape, it seems that it is possible to prevent the Brake fluid from bleeding out of the thread during the air removal work.
I wrote it as a reference, since I did not write to absolutely roll it, I thought whether it is not necessary to wind Tape.

Noticing that Brake fluid seeped out of Caliper's Air breeder
Rust was amazing as I removed it. Indeed when I thought this was dangerous, I found this product
Replaced. As I wrote that the installation was to tighten Seal tape one half turn and tighten
I rolled Emon's Seal tape. It looks more modest to the ground.
If you think that you could buy safety cheaply in the long run as it will not rust.

【What made you decide the purchase?】

Decidedly price. It's cheaper than any Oil Filter.
W800 air cooling Large type Motorcycle every 3,000 km or once every 2 Oil changes
Since Filter is also exchanged, things with cheap prices are No. 1.

【How was it actually used?】

Not bad. I think that it is comparable to Large even compared with OEM Product.

【Was it difficult to install? (Hard parts case)】

Separately, nothing is not difficult.

【Please tell me the point of installation and hang (in the case of Hard parts)】

W800 Filter cover part is dirty so if you keep it clean in advance
Work can be done easily.

【Fit feeling and height when wearing - Please tell me the weight etc (Apparel case) 】Any

[Is there anything I was disappointed about?]

Nothing in particular.

【Hope for Manufacturer - Please let me know if you have any improvement points]

From now on make cheap and good products.

【Have you compared items?】

DAYTONA, KIJIMA, OEM Productetc..

[Others]

There are things that make singing phrases such as using magnets and various other things
The point is that it is fine if you can filter Oil.
Since other Manufacturers are expendable items before doing a fancy job, we need to reduce the price
I would like you to consider it as a Large premise as a manufacturer.

I use it many times as a regular replacement, but I never felt a problem in terms of performance. Thinking of COSPA, I will continue to use it. It is a commodity you want to buy in bulk.

'