Kembali ke atas

It chose by appearance.
A portion black when grasping is collapse.

Since barrel 4 silencer was purchased, it purchased for carburetor adjustment.
Although the vehicle type which is an inclusion schedule is XR230, since FTR and jets are common, they do not interfere now.
CR125 other than XR230 of a racer is owned, and there is no disassembly of a carburetor with how often, and it is doing it.
However, since the carburetor adjustment for muffler exchange is the first, there is uneasiness for a while.
Although it is uneasy, I tried and think that he would like to deepen the knowledge about a motorcycle.
In addition, 6 oversize main jet set of POSH was purchased.

It purchased to XR230.
It is a conforming item.
Although the muffler of the barrel 4 was purchased from before the year, since the clearing work in cold inside was hard, it remained as it was until now.
Since it also becomes a good season to get warm from now on and to also ride on a motorcycle and to tamper, it goes into muffler clearing work targeting a warm day, and also performs carburetor setting out.
In addition, simultaneous purchase also of the pilot jet set product number 752306 was carried out.

I purchased Green Light because the installed Motorcycle is Z1000, but the texture is much better than I expected.
Installation can only be done by removing the original Filler cap, so it can be done in 10 seconds. Rather it may take more time to get the item out of the box ... lol

I have been on the XR 250 BAJA, which has been riding for 21 years.

I bought it because NORMAL's feeling of mnumu nuance was anxious.

After mounting, we got on the Touch which was more than expected, Snap, and easy to control

I feel that my Breaking has improved.

I wish I had to exchange it sooner..

By the way, because Rotor of Breaking system was also exchanged together, compatibility may have been good.

Every time I replace Motorcycle, I am doing it.
Oil cap around the Engine is also Black this time, I replaced it for Gold though it was one point
Every time it leaves it on the trade-in car and leaves it at hand only increases Normal oilCap (Lol)

Installation and so on are easy task of changing from Normal cap to Gold (Lol)
After all Gold is shining in black

Plug is changing in 2 to 3 years even if it is not in good condition unless it is irritable or high endurance. Indeed it is a start condition, from Idling to Red zone I ride well.

เป็นอุปกรณ์ที่ออกแบบได้สวยงาม ทั้งวัสดุและสีสัน สามารถติดตั้งได้งานด้วยตัวเองในเวลาอันสั้น และสามารถใช้ได้กับรถหลายรุ่น โดนแสดงแอกถึงประสิทธิภาพอย่างชัดเจน ทั้งการติดเครื่องยนต์ที่ง่ายขึ้น การขับขี่ทางไกลด้วยกำลังเครื่องยนต์ที่ดีขึ้นอย่างเห็นได้ชัด และการครอบของหัวเทียนมีความแน่น สามารถป้องกันน้ำหรือผุ่นละอองได้เป็นอย่างดี It is a beautifully designed device. Materials and colors Can be installed manually in a short time. And it can be used on many models. Show the yoke to clear performance. The engine is easier. Long-distance driving with noticeably improved engine power. And the cover of the spark plug. Water resistant or dustproof. (Translated by google translation)

We are attached to VTR 250. I also added a hand guard at the same time, so I do not know yet, but the fastest speed fell a bit. I expect that it will become warmer, remove the hand guard and extend the maximum speed.

I have heard the reputation of this Plug, but I tried buying it to be handled by Webike.
So far as Watani's designation OEM DPR Gap 1. I adjusted it to 3 mm and used it. Ignition system and lighting and fans (Cause of voltage eating) And is completely processing Wiring is divided.
Even when I changed Igniter and Coil "Beauty is on fire" Although I was impressed with this, I will go further up when I put this in. The cloudy rush of about 5000 rpm from Clutch meat is like Silky, it seems that generations have gone lightly for about 10 years. I feel that my heart or exhaust smell has also decreased (Lol)
However, it is said that the introduction of Wotani SPll is the Large premise as minimum as Mr. Shimaba says from the import distributor. Horribly Gap is wide so fire will not fly in the same Coil.
If the fans turn around due to heavy traffic in the summer, there are many misfires → JR 8C installed, but ... If you want to enjoy drastic solutions and fine Feel, I recommend this combination.

? 【What made you decide the purchase?】
I got my motorcycle license early 26 years ago. At the time the license was acquired, the bike that was on display at the bike shop on the way to school is equipped with separate tank type brake "Really cool!" And at that time it was shocked, I was staring through the front of the bike shop every day. Such a memorable motorcycle and separate tank type brake are one of the parts that emphasizes the custom of the motorcycle for himself. In addition, past liter bikes (CB1000SF) It was also installed. The master diameter purchased this time is the same as Grom Pure 1 / I made it to 2. Before purchase, Brembo casting master diameter that does not affect even when 4 POT brake is introduced (1 / 2 or 14 mm) in order to select it. Grom is genuine is a one-touch 2POT caliper. I examined the difference between 2POT and 4POT by pushing piston movement when changing to 4POT caliper in the future. In single-push 2 POT, one piston is pushed out and the caliper slides sideways to pinch the disc. On the contrary, in the case of 4 POT, the left and right pistons are pushed out and sandwich the disc, and the extrusion of the piston is half of 2 POT. Further calculate the hydraulic ratio, etc., this time the brake control - I want to bring the feeling close to genuine 1 / 2(12. 7 mm) for the first time.

? 【How was it actually used?】
Since we installed the same MASTER diameter as OEM, BrakeControl - Fei Ring does not change dramatically, but now CaliperHose is using OEM. Changes may be felt when changing CaliperHose in the future. In order to feel the change as future exchange schedule I would like to exchange with Hose? Caliper step by step. What changed the most - - - It was so in the CB 1000 SF era, but the Custom feeling improved.

? 【Mounting was difficult?】
Fine adjustment of replacement - It was about 1 hour work including air omission. Before replacing the Helium holder in the Lever holder. Just purchased Brake master cylinder kit has become Mirror Holder, and the Helmet holder which was installed so far can not be used. If you use it, you can not install Mirror. Since I was also doing pre-purchase before purchase, at the same time as Brake master cylinder kit KITACO Helmet Holder with Mirr

? 【Please tell me the installation point and hang】
Before removing the genuine master cylinder, remove the brake fluid from the caliper side, remove the brake fluid in the hose, and finally remove the brake fluid left in the tank. Brake fluid erodes paint. It is safe to prepare a water supply hose so that it can flow with water as soon as the brake fluid spills. Loosen the brake banjo when all brake fluid is completely removed. When loosening a banjo, it is difficult to loosen it when it is removed from the handle unless you loosen it when it is fixed to the handle. There is some brake fluid remaining in the removed banjo so you can rest assured that you wrap the banjo with waste etc.

Every time, I am working alone during installation and replacement. If you have an Assistant, have Parts and have it installed easily - Although it can be fixed, because it is a work of one person, Brake master cylinder temporary fixation is fixed with Masking tape, and in the meantime fixed with Bolt so that the installation position can be finely adjusted with Mirror Holder. Once the installation position is decided, it is final tightening. By the way Grom 's Mirror Holder regulation Torque is 10 N - m. Clutch leverClamp will also be the same provision Torque.

When the brake master cylinder installation position is decided, it is the installation of the brake banjo, but install it so that the part of the banjo becomes high position. In addition, please be sure to use a new washer when installing the banjo. Fully tighten with a banjo fastening torque of 34 N - m, replenish it so that the brake fluid will not spill into the tank, and it will be air bleeding work. Since I am using a vacuum drawing tool, it is an air removal work from the caliper side. Place the brake fluid in the tank to such an extent that it will not spill, the first time the remaining air 1 will not bite 1 / Pull out the brake fluid in the tank to about 3. In the second time, the reduced brake fluid in the tank is replenished and, as in the first cycle, the tank 1 / Remove the brake fluid so that it will remain about 3. I grasp the lever and check the touch. Lever touch "Fluffy" If it seems to be doing it, repeat air venting. Lever touch "Click" And it's done.. Since I used a vacuum drawing tool, I finished working with a large amount of air removal for about 3 times. After the air vent operation, in order to pull out fine air, I fixed it with holding the brake lever overnight.

? [Is there anything I was disappointed about?]
Although it was also in the CB 1000 SF era, it is still a good item that satisfies User. There is no disappointment!

? [Request to Manufacturer - Please let me know if you have any improvement points]
I hope Mirror installation can be installed on Mirror Holder and Master side Body, if there are two kinds of settings.

? 【Have you compared items?】
Company MASTER diameter 1 / 2(12. 7 mm) and 14 mm
Radial master (For Overspecifications, I quickly thought again!)

? [Others]
Youth age (10's) I saw that - What I felt - I can not forget what I've heard even now. As I said, I had less information, I saw it! I felt that I heard that was the best information. I spent such a time and good memories are being utilized for the current custom. information - Parts etc. are also easier to obtain than you used to, and you also got the skills to work yourself. The process that the bike custom drafted in the youth era is actually finished is irresistably fun days. Ritter bike is a fun bike life with a liter bike, "There are things that only mini can do!" So I will enjoy customizing in the future as well.

I do not mind quite how short to run normally.
I worked on only about 10 minutes. If this length, I think that you can considerably reduce Risk of Lever damage.

Discovering the Spark plug that looks like the face on the product explanation screen of Wa Big who happens to be found. Regarding its use, this plug which encourages watani attachment to the ignition system. The purchase decided immediately for a car that meets the conditions! When looking at the real thing, Steel color which Blue took first gets an eye out. The center electrode of the tapping was NGK - Compared to DR8EA, it will be positioned more towards the center of the combustion chamber by 1 mm or more, which will increase expectations for combustion efficiency Up. However, looking at the details, I can not deny the feeling that it is more complicated to make than JAPAN's Plug. BALI of the center electrode and screw terminal type terminal are obviously off center. , I feel a little cheapness because I am watching JAPAN items with high precision from the usual. However, if you actually use it and have sufficient performance and durability, you can say that it is not necessary to request such parts that are not normally visible. I installed it immediately, but the exchange itself is exactly the same as regular Plug exchange and there is no particular problem. The accuracy of the Screw part seems to be a passing point. When I try to cover Plug cap, it is Fashion that Blue 's Steel color looks sharp. And Engine start! - - - That sounds exhaust sound from Mild something more than usual. Because it is a single cylinder, there is a place called Dododo, but it is called Toto. However, rather than being cheesy rather than luxurious - - -. Also, the warm exhaust gas Gas in the winter season has Gas smell, but it feels like it has been relaxed. Impression that Engine braking became Mild when I actually ran. I have stopped playing. Furthermore, Engine vibration seems to be decreasing. Since Cowl was wearing, engine oscillation was swaying the edge of Cowl, as it was Big Li after replacing the Plug, it became impossible to see it. It is feeling that the rise is also powerful though it is Mild. I am surprised that there is such a change with just one Plug. I ran about 20 kilometers, but I did not feel Minus factor. I would like to see the impact on fuel economy and the durability of the plug itself. It is limited to strong motorcycle of watani equipped car or ignition system, but it is recommended plug at the first impression.

There is no problem at all for running normally.
The other day I fell a bit but I got scratches on the tip of Lever.
It was good to be short. (^^)

This is the second time we are wearing it, but it will start with Cell one shot. (It is natural because it is a new item) The engine is bad for a while and lastly
It was released from trouble because Starter was not used until it was not used. Opportunities to ride will also increase. After replacing the last Plug
I used it for 4 years. I will change it frequently this time.

'