Because I bought it in the spring, I thought that I do not need Screen yet.
Running at this time seems to have quite a wind effect, so in this case I looked for something good, and OEM was so expensive that I purchased this item.
I will do Impression on my attention point in a little installation.
First of all Bracket has many scratches, someone was written. - - - - - It was launched to Webby
1. First of all Screen temporarily holds Bracket
2. Spread a little Bracket on the Fork side by hand (Inside I roll a Rubber) Is included
3. Position BracketBody by placing cloth on Clamp (R, L) - - - Mark 50 mm from the top
4. While aligning Screen with ForkBracket and Light, Quantity : Pair (for Left and Right) Apply the same height so that
5. We will further tighten up each part
6. Check the final confirmation and check if there is any fun place to complete
I watched it while running, but it seems like I got hit by the wind even a little Short.
Although the product is Short, I do not know if Long was good, but I thought the resistance was low.
Although I recommend you to "Yes", installation is quite a hard work, so it is to those who can prepare and install.
I thought that it was as written by other people, but I could not feel that Torque became thin. Originally, there is only impression that it is thin like Torque, I think that it is not a level that can be realized. On the other hand, Sound seems to be getting better with Large. Especially high-speed viewing bowl has become better.
I think that it was good to replace since the Large Stress decreased as compared with NORMAL.
Everyone can install it easily if there is a 12 mm Spanner and Ratchet for installation. Even I did not take it 30 minutes from removal to installation.
It is my first exchange since I got on a new car. I am amazed by NORMALPad with about 30,000 km. Because I attached Red Pad with a different Motorcycle, I decided without comparing with others in particular. I feel that NORMAL's Rotor is bad, but it seems to be bad, but the credibility is better than NORMAL. I do not know Cost performance yet
I have not tried Plug replacement, etc. until now, it will be a perfect foster age and, on the contrary, I want to do various things by myself Today is around this time. I hope changing it after all. I feel good with a single shot start. My attachment also comes to Motorcycle more. When you do it, whatever you face is white Do not you think?. Correct Brand is the correct answer.
I installed it in REBEL 250. I bought Smoke's Long. Below
<About Fork MountingBracket>
It was full of scratches from the beginning why. It is unknown whether it is what was attached before shipment or what was attached after shipment, but it was full of scratches anyhow.
The machining accuracy itself is good, and it fits Exactly to the Inner Fork of REBEL. However, installation is a bit painful.. Bolt and Bolt holes are difficult to match very closely.
<About Screen and Bracket>
Bracket mounting holes (Hole through which Bolt passes) Because it is located on the surface of Screen. When stopping Bracket with Bolt, I'm puzzled as "various". But by never tightening Bolt tightly you can install. (Manufacturer confirmed)
<Impressions of installing and running>
The wind beneath the nose is obviously relieved. That's why the wind above the nose got stronger. Therefore, when using the Helmet with high rectifying effect, there was nothing wrong, but when using a combination of ordinary Jet helmet + Bubble shield Shield was unpleasant to shake strangely.
It is attached to REBEL 250.
It was really simple and clumsy I could install it in 15 minutes ~ 20 minutes.
It is much more compact than looking at images. Weight is also much lighter than OEM.
It becomes one turn heavy bass compared to OEM, Idling sound etc etc at the same time. Also increased by one round.
Perhaps it's a quiet residential area.
<Impression that I tried running>
The slow Torque is a thinned impression. To that extent, turning "Dappapapat" And I will accelerate well. When you turn the OEMExhaust System "Bean" A little lonely sound like feeling (Something that sounds difficult) It sounds, but this Exhaust System does not have it.
<Whether to buy or not>
decidedly "buy" is not it.
I bought it for installing a Rear box in the new REBEL 250. We decided on this product without a shipping point as it was supposed to fit only Box.
Currently, GIVI's Mono-lock case (37 liters) I am wearing. There is no problem concerning mounting. Mono-lock case Can be installed fully with Universal Installation Parts attached only. (Currently I am using Bracket which I bought at Home center with more emphasis on reliability)
The only unfortunate thing is that Carrier's overall slender construction makes it look delicate compared to other companies. A clerk at Motorcycle shop who purchased a vehicle said, "I think that it may be good to match with the car body. He told me - - -.
By the way, if you tell me the purchase price "Well, it's cheap," I was also told.
250 cc Front - Although I use both Rear, "easy to handle" I think it is a word of. Brake hose is NORMAL. Brake fluid belongs to elf.
It does not mean that the braking force is quite good. Exactly the expression that you stop only for a while holding Lever. Very easy to handle.
The first handiness is felt when speed is being adjusted while applying Rear brake at low speed.
It is easier to control the speed, so I feel that there is less flattering.
If you write like this, you may feel that Brake's effect is weak, but if you grasp it, it will stop firmly.
It is Pad that I highly recommend to those who touring the tokotoko and downtown rather than people like GunGun attacking Circuit and Pass etc..
Quantity : 1pc. The picture of the eyes is the Front which ran about 1000 km after installation. The second piece is Rear as soon as it is worn. (After running on a rainy day, please do not worry about dirt ...)
It has nothing to do with the performance of the product, but the sticker attached with extra was a bit dirty. This may be the Point you care about some people haha ??haha
【What made you decide the purchase?】 Where Arm can be mounted horizontally
【How was it actually used?】 Since installing horizontally, it gets in the way of the operation, I installed it with a slight angle raised, but Refreshing around Handlebar as Large body Image.
The area of ??Mirror is smaller than OEM as small as possible and the width is also short so we can see the blind spot on the back side, so we need to watch White by.
The reflection of Mirror can also be seen well without distortion.
Because there is weight as it is, it was not hard to see because it was shaken by vibration, but I am still not running at high speed, so I do not know what will happen if the speed goes up.
【Was it difficult to install? (Hard parts case)】 Installation Screw also comes with both Normal Thread Screw and Opposite Thread Screw, so you can install with 8 mm and 6 mm Hexagonal Wrench.
【Please tell me the point of installation and hang (in the case of Hard parts)】 Depending on Brake master, Arm may interfere, so you may need a height adjustment Adapter etc.
Because I am exchanging with Radial master, it seemed to interfere with Bleeder Bolt for bleeding air.
【Fit feeling and height when wearing - Please tell me the weight etc (Apparel case) 】Any
[Is there anything I was disappointed about?] Although it looks like Matte Black in the photograph, the actual texture is a textured feeling that the surface is fairly fine.
【Hope for Manufacturer - Please let me know if there are any improvement points】 If you match Mounting Bolt and Angle Adjustment Screw to Mirror Body and Black to Black Bolt, you will feel a sense of unity at the time of installation.
【Have you compared items?】 Napoleon OnShark Mirror 3