HONDA NSF250R
Kategori
170 Produk
Produk Terbaru
Produk Rekomendasi
![Rantai GB415HRU Seri GB Racing [Gold] - Webike Indonesia](https://imgwebikenet-e00b.kxcdn.com/catalogue/10063/gb415hru-1_TS.jpg)
Ulasan Produk
very bad quality... the product seem like a china second hand mirror ... i will not install it on my bike...cant accept it
J
SPHIA LED for Motorcycle RIZING H4 Hi/Lo [Bulb] [Special Price Items]
Distribution is also very good without problems.
![SPHIA LED for Motorcycle RIZING H4 Hi/Lo [Bulb] [Special Price Items] SPHERE LIGHT](http://img.webike.net/catalogue/images/19273/shbqc055_1_TS.jpg)
OEMValve surprisingly deteriorated severely, I chose this product of Heat sinkType from Large change high performance using other Manufacturer's LED Bulb with other two wheels.
Although Rear's Rubber cover requires a little processing to install, it is not a big problem.
Since Heat sink is exposed under the Fender behind the heat dissipation in the summer, there is no Trouble.
Depending on Manufacturer, it was said that there is a problem with quality, but there is no such worry.
There is no problem with riding the light almost every day at work without problems.
J
Brake Master Reserver Tank Cap TYPE5
Do you need packing?
To TW 225, although you purchased it, Brake fluid leaks many times. Any countermeasures. The paint of Master tank has come off The floor of the garage has become dirty.
As I was worried a lot, I was looking forward to see how it will change, but I can not see any change even if I travel normally, is it a fashion-like Parts after all?
When traveling on a highway, I felt that stability increased with high-speed Corner.
That's about it..
How much iron powder etc on Magnet etc. I'm not sure whether it is adsorbed, but with Filter + Alpha this price has a sense of security and sense of security. We will continue to use it in the future.
J
Screen Exclusive Type
For difficult installation...
Look at other people's comments
Although prepared and purchased,
It was pretty difficult....
Before struggling story, "In stock" Nevertheless, for two months for delivery
Inquiring,
There was a problem with System...
Be amazed.
○ Installation time = 2 days.
Contents of hardship
first day - - The installation target was 30 minutes, but even 90 minutes it was useless = tired so next day..
Day 2 - - Feeling newly, when looking closely, the position of the hole was Deta Lame.
In the Instruction Manual, "Hold the Screen top with your hand, while putting a little effort"
further, "While paralleling the mounting surface between Screen and the car body Bolt side"
Although attention points are written, with the momentum to break, even if you align the holes, it will not enter!
I went by two people, but it was impossible to concurrently!
I can only think that the design drawing at the production stage is incorrect!
It is not good unless you forcibly insert Bolt,
Three of the car body side Screw holes in four places, and the mountain of Screw attached collapsed!
Somehow, with oil and File Cliff, holes and Screw restored.
I tried it about 10 times but it was impossible..
As others have commented on, more than 1 cm is Gap!
In Screen's 4 places, cut the hole about twice as much as the original, finally installed!
After installation, somewhere in Screen seems to hit Front mask
I can not bear it smoothly!
A bad point - - - As stated above, installation is hard and absolute design mistake!
Good point - - Because Windshield is long both vertically and horizontally, windproof effect is absolutely Large!
○ Effect on driving - - - Actually, opening the Helmet shield does not feel the wind!
(160 cm tall) (In the past, the wind was hit hard enough to breathe... )
○ Cost surface - - - Approximately 13,000 yen is cheap, but it is a feeling that it is expensive as it was hard to install.
○ Strength surface - - - Because the strength has decreased by expanding the hole, it may be broken in 3 to 4 years...
〇 Do you recommend to others? - - - I think that it is better not to buy.
For ordinary people, I can not install easily, I get Shock,
It's a waste of time.
But, I have been able to use it for 3 to 4 years, things with better shape than this
If not,
I think I will purchase it again.
J
Exhaust System Joint Gasket (1 Set of 1pc.)
As a Gasket when using outside Aluminum silencer
【What made you decide the purchase?】 There are various Size
【How was it actually used?】 There is no problem with airtightness
【Was it difficult to install? (Hard parts case)】 Easy
【Please tell me the point of installation and hang (in the case of Hard parts)】 Subtle size adjustment is done with Gold saw
【Fit feeling and height when wearing - Please tell me the weight etc (Apparel case) 】Any
[Is there anything I was disappointed about?] Easy to adjust
【Hope for Manufacturer - Please tell me if there are any improvement points】 No particular
【Have you compared items?】 OEM Product
[Others] OEM Packing can not be used in many cases such as the Exhaust System of the Other Company Product, and it is used for size adjustment. Material wrapped iron fiber with Aluminum. If Packing's inner diameter is Small, you can adjust the Size by inserting a notch vertically with a Gold saw. I think that the error of 1? Is within the range of adjustment. There is also no exhaust leakage.
I have use this oil filter for few time last year. Good oil filter with affordable price. Fit well on the bike no leak. Can last up to 8000km. Two times oil change.