OEMValve surprisingly deteriorated severely, I chose this product of Heat sinkType from Large change high performance using other Manufacturer's LED Bulb with other two wheels.
Although Rear's Rubber cover requires a little processing to install, it is not a big problem.
Since Heat sink is exposed under the Fender behind the heat dissipation in the summer, there is no Trouble.
Depending on Manufacturer, it was said that there is a problem with quality, but there is no such worry.
There is no problem with riding the light almost every day at work without problems.
Look at other people's comments
Although prepared and purchased,
It was pretty difficult....
Before struggling story, "In stock" Nevertheless, for two months for delivery
There was a problem with System...
○ Installation time = 2 days.
Contents of hardship
first day - - The installation target was 30 minutes, but even 90 minutes it was useless = tired so next day..
Day 2 - - Feeling newly, when looking closely, the position of the hole was Deta Lame.
In the Instruction Manual, "Hold the Screen top with your hand, while putting a little effort"
further, "While paralleling the mounting surface between Screen and the car body Bolt side"
Although attention points are written, with the momentum to break, even if you align the holes, it will not enter!
I went by two people, but it was impossible to concurrently!
I can only think that the design drawing at the production stage is incorrect!
It is not good unless you forcibly insert Bolt,
Three of the car body side Screw holes in four places, and the mountain of Screw attached collapsed!
Somehow, with oil and File Cliff, holes and Screw restored.
I tried it about 10 times but it was impossible..
As others have commented on, more than 1 cm is Gap!
In Screen's 4 places, cut the hole about twice as much as the original, finally installed!
After installation, somewhere in Screen seems to hit Front mask
I can not bear it smoothly!
A bad point - - - As stated above, installation is hard and absolute design mistake!
Good point - - Because Windshield is long both vertically and horizontally, windproof effect is absolutely Large!
○ Effect on driving - - - Actually, opening the Helmet shield does not feel the wind!
(160 cm tall) (In the past, the wind was hit hard enough to breathe... )
○ Cost surface - - - Approximately 13,000 yen is cheap, but it is a feeling that it is expensive as it was hard to install.
○ Strength surface - - - Because the strength has decreased by expanding the hole, it may be broken in 3 to 4 years...
〇 Do you recommend to others? - - - I think that it is better not to buy.
For ordinary people, I can not install easily, I get Shock,
It's a waste of time.
But, I have been able to use it for 3 to 4 years, things with better shape than this
I think I will purchase it again.
【What made you decide the purchase?】 There are various Size
【How was it actually used?】 There is no problem with airtightness
【Was it difficult to install? (Hard parts case)】 Easy
【Please tell me the point of installation and hang (in the case of Hard parts)】 Subtle size adjustment is done with Gold saw
【Fit feeling and height when wearing - Please tell me the weight etc (Apparel case) 】Any
[Is there anything I was disappointed about?] Easy to adjust
【Hope for Manufacturer - Please tell me if there are any improvement points】 No particular
【Have you compared items?】 OEM Product
[Others] OEM Packing can not be used in many cases such as the Exhaust System of the Other Company Product, and it is used for size adjustment. Material wrapped iron fiber with Aluminum. If Packing's inner diameter is Small, you can adjust the Size by inserting a notch vertically with a Gold saw. I think that the error of 1? Is within the range of adjustment. There is also no exhaust leakage.
Idling's expiration has improved. I felt like running Torque had gone up again. Even though I made Downshift a little rough, my running in the city became a little easier. As for installing, since I was watching the Video of Site beforehand, it was completed in a blink of an eye. Aside from that, the bonus sticker was Parenthesis what I mind..
It is cheerful that it does not become a thing compared to OEM! It is cheap if you get this view at this price. However, as for the LED, it seems that Rose attachment tends to occur at the irradiation angle of Light, and as soon as it was installed it was upright condition even for low, so we asked Honda DREAM to adjust the optical axis. If you are thinking about HID conversion, you may consider trying LED production first.
Partly for installation, in order to use Color of Gold genus, paste Color on Screen with Double-sided Tape etc. etc etc etc etc etc etc etc etc etc etc etc. Although ingenuity is necessary, I like the appearance after wearing it is like an OEM.
If you paste HONDA 's three - dimensional Emblem in Rear in the same position as the OEM, it will be more OEM - like, so it is recommended.
The windbreak effect is much higher than OEM, and when used in conjunction with Hand guard it will be pretty comfortable in winter. However, since the width of the Screen is not wide and the height is not too high, the wind hits the Helmet and shoulders.
Because wind is hit by Helmet Ventilation works, so summer will be Merit in reverse.
In general, I like it very much..