Kembali ke atas

It exchanged together at the time of brake lever exchange.
I was easy to grasp lever form and thought that texture was also good considering a price.
A point regrettable [ one ] has GATA in a pivot part compared with a pure lever.
Operation does not seem to be affected.

I made this Filter the same as last time in the third Oil exchange.
Filter wrench is not required, there is no new expense, even in terms of performance
Since I could use it without problems, I would like to repeat it in the future.

We installed the MRA Screen on the W650, but purchased it as a measure against the coldness of the fingertip. I tried running for about 30 minutes when the maximum temperature was around 10 degrees, but I ran enough in summer Gloves.

I used this for CB 750 RC 42, Lever liked Black. It used to be a Korea made BlackLever, but I like it because it is glossy here. It is Exactly to RC 42 and there is no astringentness The operation feeling is very good

I have heard the reputation of this Plug, but I tried buying it to be handled by Webike.
So far as Watani's designation OEM DPR Gap 1. I adjusted it to 3 mm and used it. Ignition system and lighting and fans (Cause of voltage eating) And is completely processing Wiring is divided.
Even when I changed Igniter and Coil "Beauty is on fire" Although I was impressed with this, I will go further up when I put this in. The cloudy rush of about 5000 rpm from Clutch meat is like Silky, it seems that generations have gone lightly for about 10 years. I feel that my heart or exhaust smell has also decreased (Lol)
However, it is said that the introduction of Wotani SPll is the Large premise as minimum as Mr. Shimaba says from the import distributor. Horribly Gap is wide so fire will not fly in the same Coil.
If the fans turn around due to heavy traffic in the summer, there are many misfires → JR 8C installed, but ... If you want to enjoy drastic solutions and fine Feel, I recommend this combination.

Previously I used Puppy 's Handlebar Cover, but I felt bothersome on desorption and hand - operated operation I bought a WorldWalk Knuckle guard. It is also solidly made, windshield effect is high and it can respond to sudden rain all seasons seems to be used. Just when the temperature was below 5 degrees, I felt that long distances were hard even if there is Grip heater. A little more Reduction in cost It is a wonderful item that I think the number of users will increase if it can be done.

It often takes a fingertip, it is very easy to handle.
Processing by ponding is absolutely nothing.
(^^) I will also upload photos of Clutch lever.

Even when it is exchanged from OEM, there is almost no sense of incongruity in use and design.
Moreover, since the fingertip grips firmly, it does not slip and fingers slip off almost.
Because the Lever holder is Black, I got a feeling of cohesiveness and made it Black and it was the correct answer.

How much iron powder etc on Magnet etc. I'm not sure whether it is adsorbed, but with Filter + Alpha this price has a sense of security and sense of security. We will continue to use it in the future.

I bought this lever set for CB400SS, which is a vintage style motorbike and this product is very suitable and fit the style. Exspecially the chrome coating, a huge difference compare with original Honda Lever and even shinny than any other "Silver" lever. Good pricing, Good product!

I have use this oil filter for few time last year. Good oil filter with affordable price. Fit well on the bike no leak. Can last up to 8000km. Two times oil change.

Used for SHADOW 750. More than 40,000 kilos from last exchanged
Although the same Plug was also the same, there was no feeling that it was deteriorating so much even if you saw it removed, but feeling after running and running. Torque in the low revolution range returns to the extent that it reminded me that this was the time of the previous replacement, and the high revolution range also blows up to Smooth. Because it is American, it does not go to the high revolution area so much, but before that it changed with the feeling that it was blowing up like this.
I knew that it was behind the Large width since the Manufacturer recommended replacement time, but I realized that I should exchange again for chitin. After this, the 125 cc Motorcycle was also about 14 thousand kilometers, but when I replaced it with Windshield IRIDIUM, Idling was steadily stable and I could blow well well.
Plug replacement is Large thing

Motorcycle is for Mission and Engine to share Oil. In this time Shift feeling is lightly raised and lowered, Magnet effect is out. It is always the second time in 3000 km, Filter exchange at the same time, scheduled for the third time and 900 km afterwards.
It is a product that feels good even that much. Although it was a Honda OEM school, I will try this product from now on.

【What made you decide the purchase?】
I usually use the Oil Filter of DAYTONA.
Although it was not particularly dissatisfied with the performance, I tried purchasing because I wanted to try out what Magnet entrance is.

【How was it actually used?】
I was surprised to see the thing I ordered and received. I listed only Kawasaki and Honda in the adaptation model, and I felt I thought that I ordered the wrong things unexpectedly. For confirmation, confirming ProductNo by Homepage of KIJIMA was relieved without being wrong, but as long as writing the applicable car model at half end, divide it like the item of DAYTONA and divide it into Catalogue or Homepage compatibility table without writing anything I think that it is better to say Style to look at.
Although it is hard to show on the picture, the contents of the filter paper is almost the same as the number of folds compared to the one of DAYTONA.
Actually wearing, the Oil capacity of the specified Oil Filter capacity 2. For 7 Liter, 2. I put in 5 Liter and saw the state.
When it was Oil Filter of DAYTONA, it was exactly that amount, but in the Oil Filter of KIJIMA why it was put in somehow somehow, so connecting Rubber hose to Syringe and about 200 ml from the oil filling port of Oil I pulled out.
It does not seem that there is 200 ml in just the volume of Magnet inside, and I do not know whether it is a structural difference, but it is somewhat disgusting that Oil capacity will change by 200 ml just because Manufacturer is different.

【Mounting was difficult?】
I could install it without any change from Oil Filter of DAYTONA which I always use.
In the case of Cup type Filter wrench, I use Torque wrench for just in case.

【Please tell me the installation point and hang】
Those who have done it is commonsense, but do not forget to paint the engine oil on O-ring.
Also, when you remove the installed Filter, if you are tightening with the specified Torque in the case of Large resistance, the mountain will be licking in the Filter wrench of Cup type, so I will remove it separately using Band type Filter wrench I am in.

[Is there anything I was disappointed about?]
Although there is no particular problem in terms of performance, it was miscalculation that Oil capacity changed only by changing Filter's brand name. I do not know whether the structure is fundamentally different from the Filter of DAYTONA entering Magnet, but if it says as an adaptive car model you can make it according to OEM's Filter and like this time I thought I'd rather not get out of Oil.

【Hope for Manufacturer - Please let me know if you have any improvement points]
I do not say that the place of the adaptive car model described in the Package should cover all the car models, but I wanted you to write all about Manufacturer name of the car model that it adapts at the very least.

【Have you compared items?】
- DAYTONA Oil Filter 67926
I used this until I put the KIJIMA Oil Filter.
Although Magnet is not included, it is cheaper than the OEM Product, and the Oil capacity conforms to OEM Product, so I will return the next Filter exchange here.

Although there is no Trouble since installing this Filter, the Oil capacity is also reduced by 200 ml as well, so it is a bit uneasy at the high temperature in summer.
I'm still doing Oil exchanges only once, and I'm thinking I'm going to return to DAYTONA's thing if I run about 3,000 kilometers further.

I bought it for Yamaha MT-09 Racer.
I was relieved because BMW K - 100 RS which I was riding in was using K & N Filter again and again.
The good place of K & NOil Filter is convenient and comfortable to be able to be installed with Glasses without need of Filter wrench.
But the price is as high as the dimension. Is it something you can not do cheaper at a bit more.
I believe the performance is also good if the price is high ....

Postscript, O-ring Rubber is not attached, probably it is not necessary for this product separately.