First of all, the Size of the Fork attachment site is thinner than Fork, even if it can not be fixed, I thought whether it could be used if it were to be scraped off, but since it interferes partially with Brake hose, processing is necessary also on the Brake hose side.
As it is not a part that makes the effort to that extent, I gave up the installation, I can not trust Made in China again.
If Bikers' Fork Stabilizer sees product images, I think that interference with Brake hose seems to be avoidable.
Plus side : Price is cheap, around (grip) Soft, I think that it is good not to get stiff even in cold weather, individuals with many vibrations.
Minus surface : Grip becomes thick (About Grip heater included) So, for those who are Small in hands, depending on the angle of Handlebar, the thickness increases, Lever and Handlebar (Core of) There is a possibility that the thing may feel distant and it may be difficult to walk around so I think that the evaluation will break up.
Because my FUSION can not adjust the angle for Normal handle, I felt it slightly upward more than to Upright (Feeling holding down from above) became.
Because it is a Scooter which does not hold down even Positionally, the difference of several millimeters is sensuously pretty much Large.
Recommended for those who can adjust Handle position based on the thickness of Grip.
On the other hand, Direct feeling of Handlebar becomes thin, so I feel dull when I turn around.
When we arrived, it was already floating from release paper.
It seemed that the adhesive strength was not 0 and the season was still hot, so I tried adhering to Tank in the meantime and then it will float after a while.
As another means, by holding down from above for a long time, I hope that the shape of Pad itself will become familiar with Tank, I will keep curing Tape from above and keep it familiar 2 months.
I thought that it would have become familiar with it and seemed to be sticking somewhat when removing the curing tape.
But. It floated on the next day.
If you leave it like this, you will scratch the painting of Tank if you get in dust, so you only have to peel off.
It is mere Large loss.
เป็นปลอกแฮนด์ที่สวยมาก เนื้อวัสดุที่มีคุณภาพ การออกแบบที่ดี ขั้นตอนในการใส่เพียง 1-2 ขั้นตอนก็เรียบร้อย เหมาะกับการใช้งานที่หลากหลายทั้งทางใกล้และการเดินทางไกล ช่วยลดการสั่นสะเทือนในขณะขับขี่ กระชับเวลาเร่งคันเร่ง และสามารถทนต่อฝุ่นและน้ำโดยไม่ลื่นและเสื่อมสภาพ ผมใช้ในการเดินทางมากกว่า 500 กม ในครั้งเดียว และจะใช้ในการเดินทางไกลต่อไป It is a very handsome casing. Quality material Good design Step in just 1-2 steps to complete. Suitable for a wide range of applications both near and far. Reduces vibration while driving. Accelerated accelerator accelerator And can withstand dust and water without slipping and wear. I used to travel more than 500 km at one time and it is used to travel further. (translated by Google Translator)
I installed it in the new CBR 250 RR. There is no problem with Length and Pitch, but the root of Drain bolt (Washer contact surface) Is thinner than the inner diameter of Washer, so attention is required for installation. It is a product that leaks Oil if you do not loosen the Drain bolt while holding down the Washer and doing the center picking out. There is no problem if you observe the shape before mounting and understand the shape.