In the case of the SR 400 OEM's Reserve tank integrated Master cylinder, Parts itself will inevitably become Large, so Handlebar replacement etc etc. , Custom around the Handlebar may interfere with fine adjustment of the positional relationship of each part. As this product is separate from the Reserve tank, compared with OEM, the degree of freedom of the installation position is high, it is a nice point for the Custom faction.
By the way, Brake's Fing Ring itself changes obviously compared to OEM.
OEM 's Master cylinder is early Touch, the rise of braking is relatively strong and it is clearly clear, there is no change in braking force which is too large even if gradually grasping from there, a certain pressure is applied Wherever, it was Fei Ring that seemed to work strongly, but I did not like it much.
On the other hand, this product often says "Linear" It is effective. The braking force rises to Smooth by the grasping amount. I think that the diameter of Master cylinder may be different from OEM, but obviously the controllability has improved.
Of course, I think that adjustment can be done by characteristics of Brake line and Pad, so it is only comparison with Master cylinder.
Also, the Lever position adjustment mechanism of the Dial formula, which is not found in the OEM, was delightful. It can be adjusted in a moment without tools.
Wiring processing of Brake switch is necessary, but it is not so difficult task, so if you are familiar with terminal processing work, Wiring processing will end within 5 minutes.
Plus side : Price is cheap, around (grip) Soft, I think that it is good not to get stiff even in cold weather, individuals with many vibrations.
Minus surface : Grip becomes thick (About Grip heater included) So, for those who are Small in hands, depending on the angle of Handlebar, the thickness increases, Lever and Handlebar (Core of) There is a possibility that the thing may feel distant and it may be difficult to walk around so I think that the evaluation will break up.
Because my FUSION can not adjust the angle for Normal handle, I felt it slightly upward more than to Upright (Feeling holding down from above) became.
Because it is a Scooter which does not hold down even Positionally, the difference of several millimeters is sensuously pretty much Large.
Recommended for those who can adjust Handle position based on the thickness of Grip.
On the other hand, Direct feeling of Handlebar becomes thin, so I feel dull when I turn around.
เป็นปลอกแฮนด์ที่สวยมาก เนื้อวัสดุที่มีคุณภาพ การออกแบบที่ดี ขั้นตอนในการใส่เพียง 1-2 ขั้นตอนก็เรียบร้อย เหมาะกับการใช้งานที่หลากหลายทั้งทางใกล้และการเดินทางไกล ช่วยลดการสั่นสะเทือนในขณะขับขี่ กระชับเวลาเร่งคันเร่ง และสามารถทนต่อฝุ่นและน้ำโดยไม่ลื่นและเสื่อมสภาพ ผมใช้ในการเดินทางมากกว่า 500 กม ในครั้งเดียว และจะใช้ในการเดินทางไกลต่อไป It is a very handsome casing. Quality material Good design Step in just 1-2 steps to complete. Suitable for a wide range of applications both near and far. Reduces vibration while driving. Accelerated accelerator accelerator And can withstand dust and water without slipping and wear. I used to travel more than 500 km at one time and it is used to travel further. (translated by Google Translator)
I exchanged Plug because it exceeded 11000 km. Although it is an impression of about 500 km,
The attachment of Axel at 1500-3000 rpm improved, and the high rotation also turned well
I think. 5 speed 40 km is easier to run. Just 2000-3000 Partial
I feel that the area became irritable, and it became difficult to maintain a little with. I want to increase the vibration...
Because the heat value is not matched, the original Plug may be more comfortable for regular rotation. I am worrying about returning..
Looking at you..