Kembali ke atas

Comfortable grips...simple and nice. Good

It chose by appearance.
A portion black when grasping is collapse.

A parts catalog is recommended in the direction improved by itself.
If a part number is known even if it does not ask the motorcycle store, an order can be placed from Mr. webike, and I think that an incomprehensible place will also tend to carry out assembly by a service manual if the part drawing of a parts catalog is seen.
It is convenient if it is!

It exchanged together at the time of brake lever exchange.
I was easy to grasp lever form and thought that texture was also good considering a price.
A point regrettable [ one ] has GATA in a pivot part compared with a pure lever.
Operation does not seem to be affected.

It is always putting in under the sheet for the emergencies at the time of touring.
Although he does not want to encounter the opportunity for this to play an active part ...

It attaches above all and safe.
This No. 1

I have been on the XR 250 BAJA, which has been riding for 21 years.

I bought it because NORMAL's feeling of mnumu nuance was anxious.

After mounting, we got on the Touch which was more than expected, Snap, and easy to control

I feel that my Breaking has improved.

I wish I had to exchange it sooner..

By the way, because Rotor of Breaking system was also exchanged together, compatibility may have been good.

We are attached to VTR 250. I also added a hand guard at the same time, so I do not know yet, but the fastest speed fell a bit. I expect that it will become warmer, remove the hand guard and extend the maximum speed.

Although the same Besla 's Resin pad was installed close to a new article with almost no decrease, Fei Ring was bad for anything, and at the beginning Caliper and OEMMASTER pushed one after the other though I thought it was such a thing,
Even if Atari is not working as a trial, both braking performance and fee Ring have been upgraded to Large width. Dust is also less than Resin.

It is a Manufacturer that has a track record at Race in own production and can be trusted, so if you do run like a Sports run or a load as it is, it is a Recommendation.

yeah i though , i bought the long version, instead they sent me the sort version.. the material is solid , the price is affordable.. , in general i like it.

I used this for CB 750 RC 42, Lever liked Black. It used to be a Korea made BlackLever, but I like it because it is glossy here. It is Exactly to RC 42 and there is no astringentness The operation feeling is very good

I have heard the reputation of this Plug, but I tried buying it to be handled by Webike.
So far as Watani's designation OEM DPR Gap 1. I adjusted it to 3 mm and used it. Ignition system and lighting and fans (Cause of voltage eating) And is completely processing Wiring is divided.
Even when I changed Igniter and Coil "Beauty is on fire" Although I was impressed with this, I will go further up when I put this in. The cloudy rush of about 5000 rpm from Clutch meat is like Silky, it seems that generations have gone lightly for about 10 years. I feel that my heart or exhaust smell has also decreased (Lol)
However, it is said that the introduction of Wotani SPll is the Large premise as minimum as Mr. Shimaba says from the import distributor. Horribly Gap is wide so fire will not fly in the same Coil.
If the fans turn around due to heavy traffic in the summer, there are many misfires → JR 8C installed, but ... If you want to enjoy drastic solutions and fine Feel, I recommend this combination.

? 【What made you decide the purchase?】
I got my motorcycle license early 26 years ago. At the time the license was acquired, the bike that was on display at the bike shop on the way to school is equipped with separate tank type brake "Really cool!" And at that time it was shocked, I was staring through the front of the bike shop every day. Such a memorable motorcycle and separate tank type brake are one of the parts that emphasizes the custom of the motorcycle for himself. In addition, past liter bikes (CB1000SF) It was also installed. The master diameter purchased this time is the same as Grom Pure 1 / I made it to 2. Before purchase, Brembo casting master diameter that does not affect even when 4 POT brake is introduced (1 / 2 or 14 mm) in order to select it. Grom is genuine is a one-touch 2POT caliper. I examined the difference between 2POT and 4POT by pushing piston movement when changing to 4POT caliper in the future. In single-push 2 POT, one piston is pushed out and the caliper slides sideways to pinch the disc. On the contrary, in the case of 4 POT, the left and right pistons are pushed out and sandwich the disc, and the extrusion of the piston is half of 2 POT. Further calculate the hydraulic ratio, etc., this time the brake control - I want to bring the feeling close to genuine 1 / 2(12. 7 mm) for the first time.

? 【How was it actually used?】
Since we installed the same MASTER diameter as OEM, BrakeControl - Fei Ring does not change dramatically, but now CaliperHose is using OEM. Changes may be felt when changing CaliperHose in the future. In order to feel the change as future exchange schedule I would like to exchange with Hose? Caliper step by step. What changed the most - - - It was so in the CB 1000 SF era, but the Custom feeling improved.

? 【Mounting was difficult?】
Fine adjustment of replacement - It was about 1 hour work including air omission. Before replacing the Helium holder in the Lever holder. Just purchased Brake master cylinder kit has become Mirror Holder, and the Helmet holder which was installed so far can not be used. If you use it, you can not install Mirror. Since I was also doing pre-purchase before purchase, at the same time as Brake master cylinder kit KITACO Helmet Holder with Mirr

? 【Please tell me the installation point and hang】
Before removing the genuine master cylinder, remove the brake fluid from the caliper side, remove the brake fluid in the hose, and finally remove the brake fluid left in the tank. Brake fluid erodes paint. It is safe to prepare a water supply hose so that it can flow with water as soon as the brake fluid spills. Loosen the brake banjo when all brake fluid is completely removed. When loosening a banjo, it is difficult to loosen it when it is removed from the handle unless you loosen it when it is fixed to the handle. There is some brake fluid remaining in the removed banjo so you can rest assured that you wrap the banjo with waste etc.

Every time, I am working alone during installation and replacement. If you have an Assistant, have Parts and have it installed easily - Although it can be fixed, because it is a work of one person, Brake master cylinder temporary fixation is fixed with Masking tape, and in the meantime fixed with Bolt so that the installation position can be finely adjusted with Mirror Holder. Once the installation position is decided, it is final tightening. By the way Grom 's Mirror Holder regulation Torque is 10 N - m. Clutch leverClamp will also be the same provision Torque.

When the brake master cylinder installation position is decided, it is the installation of the brake banjo, but install it so that the part of the banjo becomes high position. In addition, please be sure to use a new washer when installing the banjo. Fully tighten with a banjo fastening torque of 34 N - m, replenish it so that the brake fluid will not spill into the tank, and it will be air bleeding work. Since I am using a vacuum drawing tool, it is an air removal work from the caliper side. Place the brake fluid in the tank to such an extent that it will not spill, the first time the remaining air 1 will not bite 1 / Pull out the brake fluid in the tank to about 3. In the second time, the reduced brake fluid in the tank is replenished and, as in the first cycle, the tank 1 / Remove the brake fluid so that it will remain about 3. I grasp the lever and check the touch. Lever touch "Fluffy" If it seems to be doing it, repeat air venting. Lever touch "Click" And it's done.. Since I used a vacuum drawing tool, I finished working with a large amount of air removal for about 3 times. After the air vent operation, in order to pull out fine air, I fixed it with holding the brake lever overnight.

? [Is there anything I was disappointed about?]
Although it was also in the CB 1000 SF era, it is still a good item that satisfies User. There is no disappointment!

? [Request to Manufacturer - Please let me know if you have any improvement points]
I hope Mirror installation can be installed on Mirror Holder and Master side Body, if there are two kinds of settings.

? 【Have you compared items?】
Company MASTER diameter 1 / 2(12. 7 mm) and 14 mm
Radial master (For Overspecifications, I quickly thought again!)

? [Others]
Youth age (10's) I saw that - What I felt - I can not forget what I've heard even now. As I said, I had less information, I saw it! I felt that I heard that was the best information. I spent such a time and good memories are being utilized for the current custom. information - Parts etc. are also easier to obtain than you used to, and you also got the skills to work yourself. The process that the bike custom drafted in the youth era is actually finished is irresistably fun days. Ritter bike is a fun bike life with a liter bike, "There are things that only mini can do!" So I will enjoy customizing in the future as well.

It often takes a fingertip, it is very easy to handle.
Processing by ponding is absolutely nothing.
(^^) I will also upload photos of Clutch lever.

Discovering the Spark plug that looks like the face on the product explanation screen of Wa Big who happens to be found. Regarding its use, this plug which encourages watani attachment to the ignition system. The purchase decided immediately for a car that meets the conditions! When looking at the real thing, Steel color which Blue took first gets an eye out. The center electrode of the tapping was NGK - Compared to DR8EA, it will be positioned more towards the center of the combustion chamber by 1 mm or more, which will increase expectations for combustion efficiency Up. However, looking at the details, I can not deny the feeling that it is more complicated to make than JAPAN's Plug. BALI of the center electrode and screw terminal type terminal are obviously off center. , I feel a little cheapness because I am watching JAPAN items with high precision from the usual. However, if you actually use it and have sufficient performance and durability, you can say that it is not necessary to request such parts that are not normally visible. I installed it immediately, but the exchange itself is exactly the same as regular Plug exchange and there is no particular problem. The accuracy of the Screw part seems to be a passing point. When I try to cover Plug cap, it is Fashion that Blue 's Steel color looks sharp. And Engine start! - - - That sounds exhaust sound from Mild something more than usual. Because it is a single cylinder, there is a place called Dododo, but it is called Toto. However, rather than being cheesy rather than luxurious - - -. Also, the warm exhaust gas Gas in the winter season has Gas smell, but it feels like it has been relaxed. Impression that Engine braking became Mild when I actually ran. I have stopped playing. Furthermore, Engine vibration seems to be decreasing. Since Cowl was wearing, engine oscillation was swaying the edge of Cowl, as it was Big Li after replacing the Plug, it became impossible to see it. It is feeling that the rise is also powerful though it is Mild. I am surprised that there is such a change with just one Plug. I ran about 20 kilometers, but I did not feel Minus factor. I would like to see the impact on fuel economy and the durability of the plug itself. It is limited to strong motorcycle of watani equipped car or ignition system, but it is recommended plug at the first impression.

'