Kembali ke atas

【K-CON】Nipple

    • Penilaian:

Although it carried out the acceptance side of the oil cooler of an ape and being purchased, I think that a 5-mm thing may be used by one with a long (8 mm) thread part.
This has also been used once.

  • Pengulas: Japan User(translated)
  • Ditulis pada: 2007-04-20 17:43:35
Although it carried out the acceptance side of the oil cooler of an ape and being purchased, I think that a 5-mm thing may be used by one with a long (8 mm) thread part.
This has also been used once.

Tanggapan

Jika ingin menanggapi komentar silakan "Masuk" dan menyelesaikan "Pendaftaran".

Ulasan lainnya

The ape 50 was equipped as output port of an oil cooler.
The goods themselves are made very finely and there was neither a bali nor a wound.
I think that such a little thing will lead to a manufacturer's reliance.
I think how it is that takes no less than 500 yen to this product.
Although the tapped hole was cut and attached to the clutch cover, I got it to be safer to give a pro the direction where processing of drilling etc. is diffident.
I think that it will succeed if it is processed by itself, and it takes care about the following three points.
- Put the mark on the place which punctures to a punch correctly.
- Change the drill into the thick thing gradually.
Like [ of 1 mm -> 2 mm -> 4 mm -> 6.7 mm ].
- Use cutting oil, when using drilling and a tap, and carry out slowly.
I think that it will succeed if it takes care about these.
If it practices, I will think that it is better.

It purchased as an output side of the oil cooler of an ape.
If it is those who understand the location in which a hole is made, and a size, it can be perfectly used by OK.

It can be exactly used for the output side of the oil cooler of an ape.

Although it carried out the acceptance side of the oil cooler of an ape and being purchased, I think that a 5-mm thing may be used by one with a long (8 mm) thread part.
This has also been used once.

The ape 50 was equipped as output port of an oil cooler.
The goods themselves are made very finely and there was neither a bali nor a wound.
I think that such a little thing will lead to a manufacturer's reliance.
I think how it is that takes no less than 800 yen to this product.
Although the tapped hole was cut and attached to the clutch cover, I got it to be safer to give a pro the direction where processing of drilling etc. is diffident.
I think that it will succeed if it is processed by itself, and it takes care about the following three points.
- Put the mark on the place which punctures to a punch correctly.
- Change the drill into the thick thing gradually.
Like [ of 1 mm -> 2 mm -> 4 mm -> 6.7 mm ].
- Use cutting oil, when using drilling and a tap, and carry out slowly.
I think that it will succeed if it takes care about these.
If it practices, I will think that it is better.

Although used for changing management of an oil cooler, it cannot obtain that color has only blue under the condition that size deployment is satisfactory.
Although a brake hose is also so, if it is called the parts of alumite treatment, blue red of a time-tested product is amusing.

Since the oil cooler made from a kitaco was purchased, it purchased also here.
Although exactly worked as a nipple, I would like you to prepare colors other than blue alumite.

It purchases to work. Since it is an Aluminum and structure is also lightly solid, it is satisfactory.

As the mysterious ATVPiston was blowing down on Cylinder of CT90, if you noticed, it probably became an Engine Displacement Volume that exceeded 100 CC probably, purchasing the Crank internal pressure worrisome.

Since the Material is Stainless, is not it possible to bear out despite having no Brown installation.

Because there are many uses, it is recommended for people who can not Brown with Aluminum.

I wanted to set up Breather in Fuel Tank, so I was looking for Nipple.
I was surprised to have all these pieces up.
And you can choose Size.
KITACO, you terrible!

I wanted to set up Breather in Fuel Tank, so I was looking for Nipple.
I was surprised to have all these pieces up.
And you can choose Size.
KITACO, you terrible!

As the mysterious ATVPiston was blowing down on Cylinder of CT90, if you noticed, it probably became an Engine Displacement Volume that exceeded 100 CC probably, purchasing the Crank internal pressure worrisome.

Since the Material is Stainless, is not it possible to bear out despite having no Brown installation.

Because there are many uses, it is recommended for people who can not Brown with Aluminum.

It purchases to work. Since it is an Aluminum and structure is also lightly solid, it is satisfactory.

Since the oil cooler made from a kitaco was purchased, it purchased also here.
Although exactly worked as a nipple, I would like you to prepare colors other than blue alumite.

Although used for changing management of an oil cooler, it cannot obtain that color has only blue under the condition that size deployment is satisfactory.
Although a brake hose is also so, if it is called the parts of alumite treatment, blue red of a time-tested product is amusing.

The ape 50 was equipped as output port of an oil cooler.
The goods themselves are made very finely and there was neither a bali nor a wound.
I think that such a little thing will lead to a manufacturer's reliance.
I think how it is that takes no less than 500 yen to this product.
Although the tapped hole was cut and attached to the clutch cover, I got it to be safer to give a pro the direction where processing of drilling etc. is diffident.
I think that it will succeed if it is processed by itself, and it takes care about the following three points.
- Put the mark on the place which punctures to a punch correctly.
- Change the drill into the thick thing gradually.
Like [ of 1 mm -> 2 mm -> 4 mm -> 6.7 mm ].
- Use cutting oil, when using drilling and a tap, and carry out slowly.
I think that it will succeed if it takes care about these.
If it practices, I will think that it is better.

The ape 50 was equipped as output port of an oil cooler.
The goods themselves are made very finely and there was neither a bali nor a wound.
I think that such a little thing will lead to a manufacturer's reliance.
I think how it is that takes no less than 800 yen to this product.
Although the tapped hole was cut and attached to the clutch cover, I got it to be safer to give a pro the direction where processing of drilling etc. is diffident.
I think that it will succeed if it is processed by itself, and it takes care about the following three points.
- Put the mark on the place which punctures to a punch correctly.
- Change the drill into the thick thing gradually.
Like [ of 1 mm -> 2 mm -> 4 mm -> 6.7 mm ].
- Use cutting oil, when using drilling and a tap, and carry out slowly.
I think that it will succeed if it takes care about these.
If it practices, I will think that it is better.

It can be exactly used for the output side of the oil cooler of an ape.

It purchased as an output side of the oil cooler of an ape.
If it is those who understand the location in which a hole is made, and a size, it can be perfectly used by OK.