- Beranda
- Ulasan Produk
- Sparepart Motor
- Knalpot
- Knalpot Slip-on
- Saya memutuskan untuk membeli pelindung radiator... (Dogfish: HARD HOUDAN Slip-on Silencer)
【Dogfish】HARD HOUDAN Slip-on Silencer Review
I decided to purchase this radiator guard because my radiator was getting damaged by stones. I found cheaper guards that were made from aluminum but I chose stainless steel for its durability. The reason I chose ETCHING FACTORY is because they have experi
I decided to purchase this radiator guard because my radiator was getting damaged by stones. I found cheaper guards that were made from aluminum but I chose stainless steel for its durability. The reason I chose ETCHING FACTORY is because they have experience at the SUZUKA 8 hours.
[Mounting]
*(1)Remove side cowl and under cowl.
(2)Remove the bottom screws holding the radiator.
(3)Hook on the upper 3 tabs so that they match the curved radiator and fix them together with the screws on the bottom. Be careful not to bend the guard.
*It is designed by model and will fit perfectly. Although it will rise slightly because it's only fixed with the screws on the bottom.
*Instructions aren't in detail because it's easy to mount. Only 1/3 of a letter sized paper.
[Performance]
*I tried it out after mounting but it doesn't rattle due to the vibration of the engine. But this might be because I can't hear it.
*The temperature of the water seems to be 3 to 4 degrees higher than usual. Usually when I take a ride, it settles down at around 80 degrees but it reached 85 degrees after mounting. The temperature doesn't seem to drop either. It might be because it covers the fin despite the size of the guard.
*The center slightly rises so it'll make a mess if insects intrude. You won't be able to get them out easily or clean it up easily either.
*By mounting the guard, scratches and stains become less prominent. The guard itself is made from stainless still and is scratch resistant.
[Others]
*With the know-how they achieved from their experience at The SUZUKA 8 hours, the center of the guard is produced with grids 2.3mm small to avoid stones and pebbles and 6.3mm at the sides to increase cooling performance.
*The weight of the guard is approx. 250g and is 0.8mm thick. The hard stainless steel material is ideal for guards.
*The color of the logo on the bottom part of the guard can be chose from five colors.
[General Comments]
*It is important to guard the fin of a water-cooled vehicle, however guards are expensive and can't be purchased without a sense of hesitation. So it might be best to mount it when you purchase the motorcycle after all.
Saya memutuskan untuk membeli pelindung radiator ini karena radiator saya rusak oleh batu. Saya menemukan pelindung yang lebih murah yang terbuat dari aluminium tetapi saya memilih baja tahan karat karena daya tahannya. Alasan saya memilih ETCHING FACTORY
Saya memutuskan untuk membeli pelindung radiator ini karena radiator saya rusak oleh batu. Saya menemukan pelindung yang lebih murah yang terbuat dari aluminium tetapi saya memilih baja tahan karat karena daya tahannya. Alasan saya memilih ETCHING FACTORY karena sudah berpengalaman di SUZUKA 8 jam.
[Pemasangan]
*(1) Lepas penutup samping dan penutup bawah.
(2) Lepaskan sekrup bawah yang menahan radiator.
(3) Kaitkan 3 tab atas agar sesuai dengan radiator melengkung dan kencangkan dengan sekrup di bagian bawah. Berhati-hatilah untuk tidak membengkokkan pelindung.
* Ini dirancang oleh model dan akan sangat cocok. Meskipun akan naik sedikit karena hanya dipasang dengan sekrup di bagian bawah.
*Petunjuk tidak detail karena mudah dipasang. Hanya 1/3 dari kertas berukuran letter.
[Pertunjukan]
*Saya mencobanya setelah pemasangan tetapi tidak bergetar karena getaran mesin. Tapi ini mungkin karena saya tidak bisa mendengarnya.
*Suhu air tampaknya 3 hingga 4 derajat lebih tinggi dari biasanya. Biasanya ketika saya naik, itu mereda di sekitar 80 derajat tetapi mencapai 85 derajat setelah dipasang. Temperaturnya juga sepertinya tidak turun. Mungkin karena menutupi sirip meskipun ukuran pelindung.
*Bagian tengah agak naik sehingga akan berantakan jika diganggu serangga. Anda tidak akan bisa mengeluarkannya dengan mudah atau membersihkannya dengan mudah.
*Dengan memasang pelindung, goresan dan noda menjadi kurang menonjol. Pelindungnya sendiri terbuat dari bahan stainless dan tahan gores.
[Yang lain]
*Dengan pengetahuan yang mereka peroleh dari pengalaman mereka di The SUZUKA 8 jam, bagian tengah pelindung diproduksi dengan kisi-kisi kecil 2,3mm untuk menghindari batu dan kerikil dan 6,3mm di bagian samping untuk meningkatkan kinerja pendinginan.
* Berat pelindung kira-kira. 250g dan tebal 0.8mm. Bahan stainless steel yang keras sangat ideal untuk pelindung.
*Warna logo pada bagian bawah pelindung dapat dipilih dari lima warna.
[Komentar umum]
*Penting untuk menjaga sirip kendaraan berpendingin air, namun pelindung itu mahal dan tidak dapat dibeli tanpa rasa ragu. Jadi mungkin yang terbaik adalah memasangnya saat Anda membeli sepeda motor.