- Beranda
- Ulasan Produk
- Sparepart Motor
- Rangka
- Jalu As
- Instalasi pada Poros eksternal (dibuat oleh KOOD... (BABYFACE: Axle Protector)
【BABYFACE】Axle Protector Review
Sesuai: YAMAHA MT-10, YAMAHA YZF-R1, BMW S1000RR, HONDA CBR1000RR, BMW S1000R
Installation on external Shaft (made by KOOD)
I think it depends on the type of car, but I have never had the Axle Protector touch the road surface when I have crashed my car, and I was skeptical about the necessity of this product, but I happened to see this product. However, I happened to see this product and decided to install it because it is an Axle Protector and also has a function that seems to solve the problem of slightly misaligned Axle Shaft insertion that annoys me every time when I remove the rear wheel for tire replacement or maintenance.
I ordered one that was compatible with the 2021 MT-09 model year, but since our vehicle has been replaced with a KOOD Shaft, there was a chance that it might not be able to be installed. But I couldn't do anything without checking the actual product, so I was anxious to take measurements after the product arrived at my place of business.
Of course, we have confirmed that OEM shafts can be installed without any problem, and since the thickness of KOOD shafts is larger than OEM shafts, it would be possible to install the shafts by shaving the Protector side. We hope this will be helpful for those who are replacing the shaft with other brand products.
The installation work began by measuring the inner diameter of the OEM shaft and the outer diameter of the product, and since the largest outer diameter of the press-fit part seems to be about 0.3mm larger than the shaft inner diameter, the size of the press-fit part was adjusted accordingly using water-resistance paper.
I wanted to be as even etc. as possible when applying Paper, so I wrapped Curing Tape around a cheap corded electric Drill that can be bought at Home center for a thousand yen or so, fixed Protector and applied Paper. If you don't need to use a cordless drill, I recommend it for a wide range of applications.
After adjusting the outer diameter of the Protector several times, the size of the Protector was adjusted so that it could be press-fitted into the hole, and the Funnel side could not be tapped evenly because the size of the Funnel and the Protector was too small, so it was pressed into the hole using a wooden pad.
However, it is not suitable for protecting the Hook of the Swing Arm, so if you are concerned about the Hook breaking when the Swing Arm falls over, it is better to use the Durable Receiver or remove the Hook every time after maintenance. If you are concerned about the Hook breaking when the Swing Arm falls over, it is better to use a durable support or remove the Hook every time after maintenance.
Instalasi pada Poros eksternal (dibuat oleh KOOD)
Saya pikir itu tergantung pada jenis mobilnya, tetapi saya tidak pernah memiliki Pelindung Gandar menyentuh permukaan jalan ketika saya menabrakkan mobil saya, dan saya ragu tentang perlunya produk ini, tetapi kebetulan saya melihat produk ini. Namun, saya kebetulan melihat produk ini dan memutuskan untuk memasangnya karena ini adalah Pelindung Gandar dan juga memiliki fungsi yang tampaknya menyelesaikan masalah penyisipan Poros Gandar yang sedikit tidak selaras yang mengganggu saya setiap kali melepas roda belakang untuk penggantian ban atau pemeliharaan.
Saya memesan satu yang kompatibel dengan model tahun 2021 MT-09, tetapi karena kendaraan kami telah diganti dengan KOOD Shaft, ada kemungkinan tidak dapat dipasang. Tetapi saya tidak dapat melakukan apa pun tanpa memeriksa produk yang sebenarnya, jadi saya sangat ingin melakukan pengukuran setelah produk tiba di tempat usaha saya.
Tentu saja, kami telah memastikan bahwa poros OEM dapat dipasang tanpa masalah, dan karena ketebalan poros KOOD lebih besar dari poros OEM, poros dapat dipasang dengan mencukur sisi Pelindung. Kami berharap ini akan membantu bagi mereka yang sedang mengganti poros dengan produk merek lain.
Pekerjaan instalasi dimulai dengan mengukur diameter dalam poros OEM dan diameter luar produk, dan karena diameter luar terbesar dari bagian press-fit tampaknya sekitar 0,3mm lebih besar dari diameter dalam poros, ukuran bagian press-fit disesuaikan menggunakan kertas tahan air.
Saya ingin sehalus mungkin saat menerapkan Kertas, jadi saya membungkus Curing Tape di sekitar Bor listrik berkabel murah yang dapat dibeli di pusat Rumah seharga seribu yen atau lebih, memperbaiki Pelindung dan Kertas terapan. Jika Anda tidak perlu menggunakan bor tanpa kabel, saya merekomendasikannya untuk berbagai aplikasi.
Setelah menyesuaikan diameter luar Pelindung beberapa kali, ukuran Pelindung disesuaikan sehingga bisa dimasukkan ke dalam lubang, dan sisi Corong tidak bisa diketuk secara merata karena ukuran Corong dan Pelindung terlalu besar. kecil, sehingga ditekan ke dalam lubang menggunakan bantalan kayu.
Namun, ini tidak cocok untuk melindungi Pengait Lengan Ayun, jadi jika Anda khawatir tentang Pengait patah saat Lengan Ayun jatuh, lebih baik menggunakan Penerima Tahan Lama atau melepas Pengait setiap kali setelah perawatan. Jika Anda khawatir Hook putus saat Swing Arm jatuh, lebih baik menggunakan penopang yang tahan lama atau melepas Hook setiap kali setelah perawatan.