- Beranda
- Ulasan Produk
- Sparepart Motor
- Rantai / Gear
- Dudukan Kopling
- Saya hanya ingin meringankan Kopling sedikit.... (GALE SPEED: Wire Clutch Holder Kit)
【GALE SPEED】Wire Clutch Holder Kit Review
I just wanted to lighten the Clutch up a bit.
I wanted to lighten the Clutch on my 2021 MT-09SP, so I installed a Wire Clutch Holder from Gale that can change the Ratio.
According to the information on the Net, OEMSwitch could be used, but when we tried to match the switch box with the OEMSwitch, we found that the position of the screw stop was completely opposite to that of the OEMSwitch, and the switch box had to be modified.
I measured the OEMSwitch with Caliper to make an amateur drawing for machining, procured the bracket and other necessary parts for installation at Home center, decided on the machining area required, and was about to cut it with Belt Thunder at once when my wife called me because it was her day off. Shut up." The result was far from the drawing, but we managed to fill it with Bus Coke to make it waterproof for the time being.
The New Model MT-09SP has OEMSlippers & AssistClutch, so the clutch is light, but our vehicle has an external Slipper clutch, so the Assist function is gone, and the clutch is very heavy. The clutch is light because it has an OEMSlippers&AssistClutch.
The above may not be a very helpful imprint, but the process is to shave 2mm off the back of the OEMSwitch box so that the Switch can be pressed with Gail's Lever.
When scraped, the bottom will have a hole in it, so fill it with Bus Coke or similar to make it waterproof.
*Be careful not to overfill so that the switch inside can be movable.
For installation on the body, special screws such as low-head screws and small-headed screws are required to avoid machining work as much as possible, but their availability is not so good.
And here's the most important part:when you disassemble the OEMSwitch box and put it back together again, be sure to close the lid while pushing the Switch in or the high-end Switch will be guillotined and broken. (Proven …)
Since installation, I have gone on a touring trip of about 400 km, including highways, and the Cruise Control is working fine and I have not experienced any problems so far.
The weight of the Clutch is a little lighter since the Ratio was changed from OEM 34mm to 32mm, but on the other hand, the Clutch is a little less sharp.
Also, Wire tension adjustment is much easier than OEM, so I was glad to make the change for this reason alone.
Saya hanya ingin meringankan Kopling sedikit.
Saya ingin meringankan Kopling pada MT-09SP 2021 saya, jadi saya memasang Dudukan Kopling Kawat dari Gale yang dapat mengubah Rasio.
Menurut informasi di Internet, OEMSwitch dapat digunakan, tetapi ketika kami mencoba mencocokkan kotak sakelar dengan OEMSwitch, kami menemukan bahwa posisi sekrup berhenti benar-benar berlawanan dengan OEMSwitch, dan kotak sakelar harus dimodifikasi.
Saya mengukur OEMSwitch dengan Caliper untuk membuat gambar amatir untuk pemesinan, membeli braket dan komponen lain yang diperlukan untuk pemasangan di pusat Rumah, memutuskan area pemesinan yang diperlukan, dan akan segera memotongnya dengan Belt Thunder ketika istri saya menelepon saya karena itu adalah hari liburnya. Diam." Hasilnya jauh dari gambar, tapi kami berhasil mengisinya dengan Bus Coke agar tahan air untuk sementara waktu.
Model Baru MT-09SP memiliki OEMSlippers & AssistClutch, jadi koplingnya ringan, tetapi kendaraan kami memiliki kopling Slipper eksternal, sehingga fungsi Bantuan hilang, dan koplingnya sangat berat. Koplingnya ringan karena memiliki OEMSlippers&AssistClutch.
Di atas mungkin bukan jejak yang sangat membantu, tetapi prosesnya adalah memangkas 2mm dari bagian belakang kotak OEMSwitch sehingga Switch dapat ditekan dengan Gail's Lever.
Saat dikorek, bagian bawahnya akan berlubang, jadi isi dengan Bus Coke atau sejenisnya agar tahan air.
* Berhati-hatilah agar tidak terlalu penuh sehingga sakelar di dalamnya dapat dipindahkan.
Untuk pemasangan pada bodi, sekrup khusus seperti sekrup kepala rendah dan sekrup kepala kecil diperlukan untuk menghindari pekerjaan pemesinan sebanyak mungkin, tetapi ketersediaannya tidak begitu baik.
Dan inilah bagian yang paling penting: ketika Anda membongkar kotak OEMSwitch dan memasangnya kembali, pastikan untuk menutup tutupnya sambil menekan Switch atau Switch high-end akan guillotined dan rusak. (Terbukti …)
Sejak pemasangan, saya telah melakukan perjalanan touring sekitar 400 km, termasuk jalan raya, dan Cruise Control berfungsi dengan baik dan sejauh ini saya tidak mengalami masalah.
Bobot Kopling sedikit lebih ringan karena Rasio diubah dari OEM 34mm menjadi 32mm, namun di sisi lain Kopling sedikit kurang tajam.
Selain itu, penyesuaian tegangan kabel jauh lebih mudah daripada OEM, jadi saya senang melakukan perubahan karena alasan ini saja.