Kembali ke atas

【ACCOSSATO】Racing Clutch A

Harga: IDR 4,509,245

*Termasuk PPN 10%
Webike Points: 45,092 pts

Shipping point: 6 pts ( 6 pts x 1qty)
Ubah
DKI Jakarta, Jakarta Selatan, Cilandak
Biaya pengiriman
IDR 9,000

    • Pilih varian produk:
    • Nomor Produk:
    • 400-CF007-24GR

Mohon pilih varian produk terlebih dahulu.


Model yang Sesuai:

Ninja 1000 11-14 * Dedicated switch, color, mirror holder * Boots of the switch interfere with the handle but can be used
Z1000 (Water cooling) 03-13 * Necessary dedicated switch, color, mirror holder * After 10 years model, the boot part of the switch interferes with the handle, but it can be installed
ZEPHYR 750 * Dedicated switch required | Color | Mirror holder
BRUTALE 800 * Dedicated switch, color, mirror holder
BRUTALE6 75 * Dedicated switch, color, mirror holder
GSX-R 1000 01-06 * Necessary dedicated switch, color * It is difficult to adjust the mounting position of the switch after 12 years model
GSX-R 1000 09-13 * Necessary dedicated switch, color * It is difficult to adjust the mounting position of the switch after 12 years model
Lihat lebih lanjut

Spesifikasi:

Warna tubuh : Hitam
[Ukuran]
rasio Lever : 24mm
Sesuai Kawat Stopper Diameter : 8mm atau kurang
diameter mountable Handlebar : 22. 2mm
[Spesifikasi]
Tidak mungkin untuk me-mount Inch Bar.
Hal ini dimungkinkan untuk me-mount Beralih Exclusive. Lihat lebih lanjut

Produk Terlaris

Rincian Produk

Konten ini diterjemahkan oleh Google, jika Anda ingin melihat aslinya, silakan klik Show Original

[Spesifikasi]

Warna tubuh : Hitam
[Ukuran]
rasio Lever : 24mm
Sesuai Kawat Stopper Diameter : 8mm atau kurang
diameter mountable Handlebar : 22. 2mm
[Spesifikasi]
Tidak mungkin untuk me-mount Inch Bar.
Hal ini dimungkinkan untuk me-mount Beralih Exclusive.

[Deskripsi]

Anda Clutch tidak berat?
Dengan mengubah posisi Pivot, ACCOSSATOWire kopling secara dramatis mengurangi Clutch operasi banyak model di luar UNTUK MODEL JEPANG.

Pada dasarnya ini adalah UniversalParts. Model Kesesuaian akan menjadi mobil jenis instalasi tersebut dikonfirmasi oleh perusahaan Akosat.

[Catatan]

* Operasi kopling berkurang tapi tuas stroke yang meningkat karena rasio tuas adalah 24mm yang lebih pendek dari cluth tuas OEM.
* Panjang dari adjuster di sisi pemegang ke bagian Tyco diperlukan 42 mm.
* Sesuaikan dengan adjuster di sisi mesin dalam hal panjang panjang kawat batin tidak cukup.

Model yang Sesuai

    • Ninja 1000 11-14 * Dedicated switch, color, mirror holder * Boots of the switch interfere with the handle but can be used
    • Z1000 (Water cooling) 03-13 * Necessary dedicated switch, color, mirror holder * After 10 years model, the boot part of the switch interferes with the handle, but it can be installed
    • ZEPHYR 750 * Dedicated switch required | Color | Mirror holder
    • ZEPHYR 400 * Dedicated switch required | Color | Mirror holder
    • ZZR400 94 * Dedicated switch required, color * It is necessary to cut outer wire about 7mm
    • BRUTALE 800 * Dedicated switch, color, mirror holder
    • BRUTALE6 75 * Dedicated switch, color, mirror holder
    • GSX-R 1000 01-06 * Necessary dedicated switch, color * It is difficult to adjust the mounting position of the switch after 12 years model
    • GSX-R 1000 09-13 * Necessary dedicated switch, color * It is difficult to adjust the mounting position of the switch after 12 years model
    • FZ1 02-14 * Dedicated switch, color, mirror holder
    • MT-09 * Dedicated switch, color, mirror holder
    • YZF-R1 04-14 * Dedicated switch required, color
    • YZF-R6 06-14 * Dedicated switch required, color
    • DAYTONA675 * Dedicated switch required, color
  • 4.0

    15 Ulasan

  • 5

    Sangat baik

    6

    4

    Baik

    5

    3

    Sedang

    2

    2

    Buruk

    2

    1

    Buruk

    0
  • Tulis Ulasan
  • It is a luxury Lever. Parenthesis is good with Italian design.

    2017/07/01

    by Japan User(translated)
    For Race parts, Clutch Wire's play adjustment stage is miscellaneous and adjusted If it is only Screw, it will be either panpan or dardal. After all it was finally a little dissatisfied because it was an adjustment on the engine side but overall I like it.
  • I got a little light.

    2017/02/12

    by Japan User(translated)
    This is also an issue from the time of purchase, more specifically from the VTR 1000 F that was on the old days.There is a person who seems to like grip strength training, but I will let you through here.Although I knew there was a Parts that makes it easier to grasp in the exchange of Clutch lever in the story, it was a half-trusted one so I had been watching it until now, but this time I thought about putting a hand here.I also posted a comparison photo with OEMLever, but the position has moved. Lever's Adjuster position attached to it is also the tenth in 11 steps. I wonder if this is a referenceAlthough it can be done with a pump, an OEM Clutch holder can not come off unless you take a Grip or Switch housing, so you need an adhesive to reinstall the Grip.Well Lever's color is a world of self-satisfaction but I think it was good to be Blue.Well, I am satisfied with my looks, it's Clutch adjustment, is it a bit severe ??As I looked at other writers, I thought that it would change quite a bit with Nut half turn on the engine side as it severe. Well I might be used to it.. If you do it basically and then do it in Adjuster on the Lever side Large is durable. Because I say on machine Onchi.It is harder to do it unless you remove Cowl when adjusting Adjuster on the Engine side than that. Nothing. Slightly scratched by Spanner. Maintenance is hard to do is the fate of Full cowl.It is about 20% that it got lighter?There is no doubt that it got lighter, but it is still difficult to make it numeric. I feel it is difficult to grasp with three fingers.And the place where Clutch connects is completely different from what I have ever been. I do not know if it's time to adjust this, but if you hold it for a while the place was half a crane position. Although it is a problem of familiarity, I was a little puzzled.In this way, I would like to make Brake lever made by Ascot this time, but as we are refraining from car inspection, it is impossible to spend more than this ~.Clutch switch and Color are written in different impressions.Both of them are not mandatory, but I would like to put them if possible.
  • I am very satisfied..

    2016/12/07

    by Japan User(translated)
    - Clutch adjustment and Clutch switch (BeringerClutch switch) I was not confident of the adjustmentSo I brought it to the store where I purchased Motorcycle.- Clutch lightened dramatically after installation.- Although it is a Clutch switch, using a Tester, it is bonded to a delicate position, and WiringI was able to install without processing the existing Wiring.- It is the position of the Clutch lever, but if it is adjusted very close to Grip, Clutch can not be completely cutBecome.- I think Clutch Wire Collar still needs it.
  • It was nice to change..

    2016/02/29

    by Japan User(translated)
    It was nice to change the heavy Clutch lever so far. I think that we can also issue Manufacturer from the beginning. Because I do not seem to be able to replace it all by myself, I changed it with Red Baron. If you are suffering from the weight of the Clutch lever in the Large type Motorcycle it would be better to change it at once.
  • Personally it was a somewhat effective effect.

    2015/04/15

    by Japan User(translated)
    I installed it in the 2014 model.Installation itself is quite easy. Even if Grip goes away, it will be in a flash. I think that it is lucky if you injure the angle to Handlebar before loosing Clamp lever 's Clamp.It is easier to adjust later if you loosen the stop on Clutch side before fitting Wire to Lever. Cowl may be in the way.If the Clutch switch is made by ACOSAT, contact and Switch sides are too long to interfere with Handlebar. I can gill it if it is made by other people Impre street, Beringer, and the Fasten terminal can be used as it is so it looks and construction is easy.As a precaution, when the Wire adjustment screw on the Lever side is pulled out too much, the round rod of the Click mechanism and Spring drop off.Although I came around after the exchange, on my own it became a little lighter, it was a change in the position. Originally it was light, so I thought that it will not change much, but if there is such a change, it seems to run comfortably when going out.As Italy's Manufacturer seems, Design is good, but in some places BALI remained. It looks like Italy is not it.Delivery is a problem after that.
15 Ulasan Lihat semua

Produk Teratas

【ZETA】Pilot Lever Clutch
Pilot Lever Clutch ZETA
【ACCOSSATO】Racing Clutch A
Racing Clutch A ACCOSSATO
【SP Takegawa: SP Takegawa】Quick Clutch Lever Assembly
Quick Clutch Lever Assembly SP Takegawa: SP Takegawa
【ACCOSSATO】Wire Clutch Lever
Wire Clutch Lever ACCOSSATO
【ZETA】Pilot Lever Brake
Pilot Lever Brake ZETA
【ZETA】Pilot Lever Brake
Pilot Lever Brake ZETA
【ZETA】Pilot Lever Brake
Pilot Lever Brake ZETA
【brembo】Mechanical Clutch Lever Kit
Mechanical Clutch Lever Kit brembo
【SP Takegawa: SP Takegawa】Chromium Plating Lever (Brake Lever)
Chromium Plating Lever (Brake Lever) SP Takegawa: SP Takegawa
【KIJIMA】Lever Brake Black Adjust
Lever Brake Black Adjust KIJIMA
【SP Takegawa: SP Takegawa】High Performance Z Lever
High Performance Z Lever SP Takegawa: SP Takegawa
【ACCOSSATO】CNC Brake Lever F016
CNC Brake Lever F016 ACCOSSATO
【KN Planning】Dual Color Lever Disc 2
Dual Color Lever Disc 2 KN Planning
【SP Takegawa: SP Takegawa】High Performance Z Lever
High Performance Z Lever SP Takegawa: SP Takegawa
【ARC】Composite Brake Lever
Composite Brake Lever ARC
【SP Takegawa: SP Takegawa】Standard Clutch Lever & Cable
Standard Clutch Lever & Cable SP Takegawa: SP Takegawa
【KITACO】Billet Lever
Billet Lever KITACO
【KN Planning】Dual Color Lever [Drum]
Dual Color Lever [Drum] KN Planning
【ZETA】Pivot Street Lever Set
Pivot Street Lever Set ZETA
【RC ENGINEERING】Clutch Bearing System
Clutch Bearing System RC ENGINEERING