- Beranda
- Motor
- HONDA 401 - 750cc
- CBR600F
- Sparepart Motor
- Rangka
- Engine Slider / Frame Slider
- BATTLE FACTORY
- BATTLE FACTORY: Frame Slider (Tidak Sesuai Peraturan MFJ)
Frame Slider (Tidak Sesuai Peraturan MFJ)
- Nomor produk: BA13-H01B
-
- IN STOCK
- Out Stock
- BATTLE FACTORY
- |
- 0.0
- (0 ulasan)
Cek kupon saya
Jumlah
100% Ori
Garansi 7 hr
Gratis Cashback
Nett Tanpa Biaya Tambahan
Model yang Sesuai
Lihat SemuaRincian Produk
Konten ini diterjemahkan oleh Google, jika Anda ingin melihat aslinya, silakan klik
Lihat versi asli
Spesifikasi:
Warna : Hitam
MFJ Non-Sesuai Produk Color: Black
Products not compatible with MFJ
MFJ Non-Sesuai Produk Color: Black
Products not compatible with MFJ
[Deskripsi]
● Dengan melampirkan pelindung Crash, ketika Crankcase, Coveretc. Untuk batas Kecil minimum. Hal ini juga mencegah bencana sekunder karena hamburan Minyak untuk kendaraan berikutnya, dan masih dapat mempertahankan negara sendiri berjalan.
● Materi tidak umum digunakan resin DURACON, PP bahan yang digunakan, dan kekerasan yang tepat dan gaya gesekan yang tepat dijamin. (Dalam kasus resin DURACON, kekerasan yang terlalu tinggi untuk menyerap kejutan dan ada kemungkinan merusak Crankcase dan Cylinder kepala. )
- Hal ini dapat digunakan dalam arti Lampiran juga untuk kendaraan untuk jalan umum umum, Crankcase, Cover, Cowletc. Anda dapat menghentikan kerusakan batas Terkecil. (MFJ produk non-compliant dianjurkan. ) ●The crash protector minimizes the risk of damage to the crankcase and cover in the event of an accident.In addition, this prevents secondary disasters caused by oil splashing to the following vehicle and keeps the vehicle in a state where it can drive itself.
●PP material is used instead of the commonly used Duracon® resin to ensure appropriate hardness and friction.(In the case of Duracon® esin, the hardness is too high to absorb the impact and may damage the crankcase or cylinder head.)
●It can be used as an accessory for general public road vehicles, and can minimize damage to the crankcase, cover, cowl, etc. in the event of an accident.(MFJ non-compliant products are recommended.)
● Materi tidak umum digunakan resin DURACON, PP bahan yang digunakan, dan kekerasan yang tepat dan gaya gesekan yang tepat dijamin. (Dalam kasus resin DURACON, kekerasan yang terlalu tinggi untuk menyerap kejutan dan ada kemungkinan merusak Crankcase dan Cylinder kepala. )
- Hal ini dapat digunakan dalam arti Lampiran juga untuk kendaraan untuk jalan umum umum, Crankcase, Cover, Cowletc. Anda dapat menghentikan kerusakan batas Terkecil. (MFJ produk non-compliant dianjurkan. ) ●The crash protector minimizes the risk of damage to the crankcase and cover in the event of an accident.In addition, this prevents secondary disasters caused by oil splashing to the following vehicle and keeps the vehicle in a state where it can drive itself.
●PP material is used instead of the commonly used Duracon® resin to ensure appropriate hardness and friction.(In the case of Duracon® esin, the hardness is too high to absorb the impact and may damage the crankcase or cylinder head.)
●It can be used as an accessory for general public road vehicles, and can minimize damage to the crankcase, cover, cowl, etc. in the event of an accident.(MFJ non-compliant products are recommended.)
Catatan
Jenis lain di sini
Other types are here
Peringatan
* Ini adalah sekitar 40mm dari kerudung.
* Bentuk pelindung ujung adalah peraturan MFJ sesuai 10R.
* Ini tidak sesuai dengan peraturan MFJ karena sekitar 40mm dari kerudung.
* Pengeboran lubang di kerudung yang diperlukan.
*CATATAN : Harap dicatat bahwa ada kasus bahwa tujuan asli tidak dapat mencapai tergantung pada kondisi ketika jatuh dan kecelakaan.
* Jangan melompati 20mm dari kerudung yang merevisi peraturan 03MFJ. (Kendaraan yang sesuai adalah JSB, ST600. ) Bentuk R dari 10R atau lebih telah ditambahkan. Namun, kami sedang mempersiapkan MFJ sesuai produk untuk pemeriksaan balap di perusahaan kami karena tanah tidak jelas tapi kami merekomendasikan item lagi bentuk R sekitar 20mm dari 10R panjang keseluruhan sama dari produk yang sesuai MFJ. (MFJ Non-sesuai Produk)
* Untuk tujuan awal, itu lebih tepat bagi mereka MFJ Non-sesuai Produk. Kami juga mengakui bahwa tidak ada masalah dengan bahaya bila menggunakan di sirkuit. *Duracon® is a registered trademark of Polyplastics Corporation in Japan and other countries.
*It sticks out approx. 40mm from the cowl.
*Protector tip shape is MFJ regulation compatible 10R.
*It is not compatible with MFJ regulation because it sticks out approx. 40mm from the cowl.
*Cowl needs to be drilled.
*Note: Depending on the circumstances of the fall or accident, the original purpose may not be achieved.
*'03 MFJ regulation has been revised and it must not protrude more than 20mm from the cowl.(Applicable vehicles are JSB and ST600 only) In addition, the tip must be more than 10R R shape.However, since the basis is unclear, Battle Factory has prepared MFJ compatible products for race vehicle inspection, but for practice and for general public roads, they recommend the same 10R R shape and 20mm longer overall length than MFJ compatible products.(MFJ non-compliant product)
*For the original purpose, the non-MFJ compatible products are more appropriate.In addition, it is recognized that there is no problem of danger in the circuit.
*There may be changes in product specifications due to the manufacturer's reasons.
* Bentuk pelindung ujung adalah peraturan MFJ sesuai 10R.
* Ini tidak sesuai dengan peraturan MFJ karena sekitar 40mm dari kerudung.
* Pengeboran lubang di kerudung yang diperlukan.
*CATATAN : Harap dicatat bahwa ada kasus bahwa tujuan asli tidak dapat mencapai tergantung pada kondisi ketika jatuh dan kecelakaan.
* Jangan melompati 20mm dari kerudung yang merevisi peraturan 03MFJ. (Kendaraan yang sesuai adalah JSB, ST600. ) Bentuk R dari 10R atau lebih telah ditambahkan. Namun, kami sedang mempersiapkan MFJ sesuai produk untuk pemeriksaan balap di perusahaan kami karena tanah tidak jelas tapi kami merekomendasikan item lagi bentuk R sekitar 20mm dari 10R panjang keseluruhan sama dari produk yang sesuai MFJ. (MFJ Non-sesuai Produk)
* Untuk tujuan awal, itu lebih tepat bagi mereka MFJ Non-sesuai Produk. Kami juga mengakui bahwa tidak ada masalah dengan bahaya bila menggunakan di sirkuit. *Duracon® is a registered trademark of Polyplastics Corporation in Japan and other countries.
*It sticks out approx. 40mm from the cowl.
*Protector tip shape is MFJ regulation compatible 10R.
*It is not compatible with MFJ regulation because it sticks out approx. 40mm from the cowl.
*Cowl needs to be drilled.
*Note: Depending on the circumstances of the fall or accident, the original purpose may not be achieved.
*'03 MFJ regulation has been revised and it must not protrude more than 20mm from the cowl.(Applicable vehicles are JSB and ST600 only) In addition, the tip must be more than 10R R shape.However, since the basis is unclear, Battle Factory has prepared MFJ compatible products for race vehicle inspection, but for practice and for general public roads, they recommend the same 10R R shape and 20mm longer overall length than MFJ compatible products.(MFJ non-compliant product)
*For the original purpose, the non-MFJ compatible products are more appropriate.In addition, it is recognized that there is no problem of danger in the circuit.
*There may be changes in product specifications due to the manufacturer's reasons.
Model yang Sesuai
PRODUK YANG JUGA DILIHAT
Produk Siap Dikirim dari Gudang Jepang
Rekomendasi buat Kamu
Best Seller
New Custom Article
Gunakan kupon
Review Gambar
Review detail
/