- Beranda
- Sparepart Motor
- Suspensi / Rearset / Velg / Swingarm
- Suspensi / Shock Belakang
- Preload Adjuster
- PMC
- PMC: Billet Preload Adjuster
Cek kupon saya
Jumlah
100% Ori
Garansi 7 hr
Gratis Cashback
Nett Tanpa Biaya Tambahan
Model yang Sesuai
Lihat SemuaRincian Produk
Konten ini diterjemahkan oleh Google, jika Anda ingin melihat aslinya, silakan klik
Lihat versi asli
Spesifikasi:
• untuk KYB Fork
■For KYB Fork
[Deskripsi]
Initial Adjuster untuk ADVANTAGE-KYB yang telah lama ditunggu-tunggu
Hilangkan tonjolan
Mungkin sulit untuk menyetel penyetel awal pada bagian atas garpu seri Z karena posisi setang.. Jadi, Spec dirancang untuk menjaga bentuk bagian atas area fokus tidak berubah bahkan setelah menyesuaikan adjuster.. Aku melakukannya..
Hex spesialisasi kami
Bagian pengoperasian Adjuster adalah Hex 8mm dengan bentuk cekung.. Hal ini membuat operasi penyetel lebih mudah dan lebih akurat dengan kunci pas titik bola, bahkan saat menggunakan batang offset pendek dan batang dengan tinggi sangat rendah ..
VCut alur
Alur VCTut disediakan pada permukaan yang tidak terlihat untuk mengurangi resistansi permukaan AdjusterThrust untuk mempermudah operasi penyetelan.
Thrust Washer
Washer dorong khusus dipasang ke bidang kontak antara pegas dan ujung penyetel, yang mencegah perubahan apa pun dalam tahanan operasi penyetel meskipun gaya tolak pegas berubah selama penyetelan.
Sesuaikan rentang
KYB36Z dan 36KZ dapat disesuaikan dari -5mm hingga + 15mm dengan menggunakan pipa bagian dalam yang disertakan ..
KYB38 dan 38R dapat disesuaikan dari -6mm hingga + 14mm hanya dengan mengganti pengatur Perlengkapan Standar. The long-awaited initial adjuster for exclusive use with ADVANTAGE-KYB
■Eliminate protrusions
The Z series fork tops are sometimes difficult to adjust the initial adjuster due to the position of the handlebar.Therefore, the shape of the fold-top does not change even if the adjuster is adjusted.
■The particular HEX
The operating part of the adjuster is a concave 8mm hex.This makes it easy and accurate to operate the adjuster with a ball point hex wrench, even with short offset stems and very low height handlebars.
■V-cut groove
V-cut grooves are also provided on the invisible surface to reduce the surface resistance of the adjuster thrust as much as possible, realizing light adjustment operation.
■Thrust Washers
A special thrust washer is attached to the contact area between the adjuster tip and the spring to suppress changes in resistance to adjuster operation even when the repulsive force of the spring changes during adjustment.
■Adjusting Range
KYB36Z and 36KZ can be adjusted from -5mm to +15mm by using the included inner pipe.
KYB38 and 38R can be adjusted from -6mm to +14mm by simply replacing the standard equipped adjuster.
Hilangkan tonjolan
Mungkin sulit untuk menyetel penyetel awal pada bagian atas garpu seri Z karena posisi setang.. Jadi, Spec dirancang untuk menjaga bentuk bagian atas area fokus tidak berubah bahkan setelah menyesuaikan adjuster.. Aku melakukannya..
Hex spesialisasi kami
Bagian pengoperasian Adjuster adalah Hex 8mm dengan bentuk cekung.. Hal ini membuat operasi penyetel lebih mudah dan lebih akurat dengan kunci pas titik bola, bahkan saat menggunakan batang offset pendek dan batang dengan tinggi sangat rendah ..
VCut alur
Alur VCTut disediakan pada permukaan yang tidak terlihat untuk mengurangi resistansi permukaan AdjusterThrust untuk mempermudah operasi penyetelan.
Thrust Washer
Washer dorong khusus dipasang ke bidang kontak antara pegas dan ujung penyetel, yang mencegah perubahan apa pun dalam tahanan operasi penyetel meskipun gaya tolak pegas berubah selama penyetelan.
Sesuaikan rentang
KYB36Z dan 36KZ dapat disesuaikan dari -5mm hingga + 15mm dengan menggunakan pipa bagian dalam yang disertakan ..
KYB38 dan 38R dapat disesuaikan dari -6mm hingga + 14mm hanya dengan mengganti pengatur Perlengkapan Standar. The long-awaited initial adjuster for exclusive use with ADVANTAGE-KYB
■Eliminate protrusions
The Z series fork tops are sometimes difficult to adjust the initial adjuster due to the position of the handlebar.Therefore, the shape of the fold-top does not change even if the adjuster is adjusted.
■The particular HEX
The operating part of the adjuster is a concave 8mm hex.This makes it easy and accurate to operate the adjuster with a ball point hex wrench, even with short offset stems and very low height handlebars.
■V-cut groove
V-cut grooves are also provided on the invisible surface to reduce the surface resistance of the adjuster thrust as much as possible, realizing light adjustment operation.
■Thrust Washers
A special thrust washer is attached to the contact area between the adjuster tip and the spring to suppress changes in resistance to adjuster operation even when the repulsive force of the spring changes during adjustment.
■Adjusting Range
KYB36Z and 36KZ can be adjusted from -5mm to +15mm by using the included inner pipe.
KYB38 and 38R can be adjusted from -6mm to +14mm by simply replacing the standard equipped adjuster.
Catatan
* Gambar hanya untuk referensi. Gambar yang ditampilkan mungkin berbeda dari produk yang sebenarnya.
PRODUK YANG JUGA DILIHAT
Produk Siap Dikirim dari Gudang Jepang
Rekomendasi buat Kamu
Best Seller
New Custom Article
Gunakan kupon
Review Gambar
Review detail
/