- Beranda
- Sparepart Motor
- Kelistrikan
- Lampu
- Aksesoris LED
- AMC
- AMC: LED Blinker Position Silicon Tube
LED Blinker Position Silicon Tube
- Nomor produk: LETT601-BL/OR2
-
- IN STOCK
- Out Stock
- AMC
- |
- 0.0
- (0 ulasan)
Cek kupon saya
Jumlah
100% Ori
Garansi 7 hr
Gratis Cashback
Nett Tanpa Biaya Tambahan
Rincian Produk
Konten ini diterjemahkan oleh Google, jika Anda ingin melihat aslinya, silakan klik
Lihat versi asli
Spesifikasi:
[Kuantitas] LED : SMD150 x2pc berturut-turut
[Ukuran] (Sekitar) Panjang 600mm x Lebar 9mm x Tebal 14mm
[Termasuk Bagian] Bagian Memperbaiki Tabung
[Spesifikasi]
Can Sera Built-in
Tegangan : 12V
[Quantity] LED: SMD150s x 2 pcs
[Size] (approx.) Length 600mm X Width 9mm X Thickness 14mm
[Components] Tube fixing parts
[Specification]
・Built-in canceller
・Voltage: 12V
[Ukuran] (Sekitar) Panjang 600mm x Lebar 9mm x Tebal 14mm
[Termasuk Bagian] Bagian Memperbaiki Tabung
[Spesifikasi]
Can Sera Built-in
Tegangan : 12V
[Quantity] LED: SMD150s x 2 pcs
[Size] (approx.) Length 600mm X Width 9mm X Thickness 14mm
[Components] Tube fixing parts
[Specification]
・Built-in canceller
・Voltage: 12V
[Deskripsi]
Dapat dihubungkan ke posisi sinyal belok.
Bicolor LED Silicon Tube Light!
Relatif mudah dipasang karena tidak ada unit pengontrol ..
Anda bisa mendorongnya ke celah antara lampu depan dan bumper untuk mendapatkan tampilan AUDI!
Tabungnya terbuat dari silikon yang lembut, sehingga bisa ditekuk dengan bebas ..
Itu dapat dipasang pada permukaan melengkung, yang sulit dilakukan dengan pita konvensional!
LED dipasang di tabung silikon, sehingga seluruh tabung terlihat menyala seragam ..
Anda juga dapat memotongnya sesuai panjang yang Anda inginkan ..
Setiap 3LED (sekitar. 25mm) bisa dipotong ..
Dempul di permukaan yang dipotong ..
Anda bisa mengoleskan lem atau bahan lain padanya .. Interlocking with the indicator position is also OK.
■Two-color LED silicon tube light!
Since there is no controller unit, installation is relatively easy.
You can even push it into the gap between the headlight and the bumper for an AUDI look!
The tube is made of soft silicone and can be bent freely.
It can be mounted on curved surfaces, which has been difficult to do with conventional tapes!
The LED is installed inside the silicon tube, so the whole tube appears to glow evenly.
■You can also use it by cutting it at the length you like.
It is possible to cut every 3LED (about 25mm).
The cut surface should be caulked.
Just apply some glue and you're good to go.
Bicolor LED Silicon Tube Light!
Relatif mudah dipasang karena tidak ada unit pengontrol ..
Anda bisa mendorongnya ke celah antara lampu depan dan bumper untuk mendapatkan tampilan AUDI!
Tabungnya terbuat dari silikon yang lembut, sehingga bisa ditekuk dengan bebas ..
Itu dapat dipasang pada permukaan melengkung, yang sulit dilakukan dengan pita konvensional!
LED dipasang di tabung silikon, sehingga seluruh tabung terlihat menyala seragam ..
Anda juga dapat memotongnya sesuai panjang yang Anda inginkan ..
Setiap 3LED (sekitar. 25mm) bisa dipotong ..
Dempul di permukaan yang dipotong ..
Anda bisa mengoleskan lem atau bahan lain padanya .. Interlocking with the indicator position is also OK.
■Two-color LED silicon tube light!
Since there is no controller unit, installation is relatively easy.
You can even push it into the gap between the headlight and the bumper for an AUDI look!
The tube is made of soft silicone and can be bent freely.
It can be mounted on curved surfaces, which has been difficult to do with conventional tapes!
The LED is installed inside the silicon tube, so the whole tube appears to glow evenly.
■You can also use it by cutting it at the length you like.
It is possible to cut every 3LED (about 25mm).
The cut surface should be caulked.
Just apply some glue and you're good to go.
Peringatan
* Korsleting sirkuit dan produk rusak saat memotong dalam keadaan berenergi.
Ada kasus di mana sedikit arus mengalir atau disimpan bahkan sakelar MATI tergantung di mana Anda mengambil daya. Harap pastikan untuk melepaskan ketiga kabel dari selotip sebelum memotong.
* Sambungkan secara terbalik + - jika tidak berfungsi karena LED memiliki polaritas.
* Ini adalah ukuran tahan air tetapi sedikit berbahaya karena merupakan produksi luar negeri. Sebagai tindakan pencegahan, disarankan untuk mengambil tindakan kedap air sebelum digunakan.
* Silakan periksa di foto mengenai detail metode kabel.
* Ini adalah bahan yang fleksibel tetapi ditekuk pada sudut yang tajam. Mengencangkan dengan kuat akan menyebabkan sirkuit mati dan tidak berfungsi. *Cutting the product while it is energized will short-circuit the circuit and damage the product.
Depending on the location of the power source, a small amount of current may be flowing or stored even when the switch is off.Be sure to remove all three wires from the tape before cutting.
*If the LED does not light up, connect the + and - terminals in reverse order.
*It's waterproof, but I'm a little nervous because it's made non Japanese.To be sure, it is recommended to take waterproof measures before use.
*Please refer to the wiring method in the image.
*The material is flexible, but if it is bent at a sharp angle or twisted strongly, it may break the circuit and cause a failure.
Ada kasus di mana sedikit arus mengalir atau disimpan bahkan sakelar MATI tergantung di mana Anda mengambil daya. Harap pastikan untuk melepaskan ketiga kabel dari selotip sebelum memotong.
* Sambungkan secara terbalik + - jika tidak berfungsi karena LED memiliki polaritas.
* Ini adalah ukuran tahan air tetapi sedikit berbahaya karena merupakan produksi luar negeri. Sebagai tindakan pencegahan, disarankan untuk mengambil tindakan kedap air sebelum digunakan.
* Silakan periksa di foto mengenai detail metode kabel.
* Ini adalah bahan yang fleksibel tetapi ditekuk pada sudut yang tajam. Mengencangkan dengan kuat akan menyebabkan sirkuit mati dan tidak berfungsi. *Cutting the product while it is energized will short-circuit the circuit and damage the product.
Depending on the location of the power source, a small amount of current may be flowing or stored even when the switch is off.Be sure to remove all three wires from the tape before cutting.
*If the LED does not light up, connect the + and - terminals in reverse order.
*It's waterproof, but I'm a little nervous because it's made non Japanese.To be sure, it is recommended to take waterproof measures before use.
*Please refer to the wiring method in the image.
*The material is flexible, but if it is bent at a sharp angle or twisted strongly, it may break the circuit and cause a failure.
PRODUK YANG JUGA DILIHAT
Produk Siap Dikirim dari Gudang Jepang
Rekomendasi buat Kamu
Best Seller
New Custom Article
Gunakan kupon
Review Gambar
Review detail
/