Cek kupon saya
Jumlah
100% Ori
Garansi 7 hr
Gratis Cashback
Nett Tanpa Biaya Tambahan
Model yang Sesuai
Lihat SemuaRincian Produk
Konten ini diterjemahkan oleh Google, jika Anda ingin melihat aslinya, silakan klik
Lihat versi asli
Spesifikasi:
[Rentang pemakaian] P.C.D140-280mm
[Applicable range]P.C.D140-280mm
[Deskripsi]
Produk adalah penarik yang melepas lengan ayun seperti HONDA PCX125 / 150 dari poros roda gigi akhir. Ini adalah alat yang bantalan dan poros roda gigi terakhir dari lengan ayun aktif dalam pekerjaan yang sulit untuk dilepaskan hingga saat ini dengan memperbaikinya dengan karat dan pekerjaan ditingkatkan secara efisien.
Dapat digunakan untuk melepaskan lengan ayun skuter.
Dengan pelindung yang melindungi poros
Perakitan bagian suspensi sesuai dengan tahap
Untuk baut yang tahan torsi tinggi
[PROSEDUR]
Lepaskan mur poros untuk menentukan apakah lengan ayun harus dilepas dengan tangan.
Pastikan setiap bagian sudah terpasang dengan kencang dan kencangkan baut penarik. ■This product is a puller to remove the scooter swingarm from the final gear shaft.
This tool is used to remove swingarm bearings and final gear shafts that have been difficult to remove due to rust and other factors, improving work efficiency.
■Used to remove and install the swingarm of scooters
■With a protector to protect the shaft
■Assembly in accordance with the step of the suspension part
■Special bolt to withstand high torque
■Remove the axle nut and check if the swingarm can be removed by hand.
■Tighten the puller bolt after confirming that each part has been assembled securely.
[Procedure]
[1]Remove the axle nut and check if the swingarm can be removed by hand.(Scope of Application: P.C.D up to 140-280mm)
[2] Make sure that each part is securely assembled and tighten the puller bolts.Bike assembly: PCX125
Dapat digunakan untuk melepaskan lengan ayun skuter.
Dengan pelindung yang melindungi poros
Perakitan bagian suspensi sesuai dengan tahap
Untuk baut yang tahan torsi tinggi
[PROSEDUR]
Lepaskan mur poros untuk menentukan apakah lengan ayun harus dilepas dengan tangan.
Pastikan setiap bagian sudah terpasang dengan kencang dan kencangkan baut penarik. ■This product is a puller to remove the scooter swingarm from the final gear shaft.
This tool is used to remove swingarm bearings and final gear shafts that have been difficult to remove due to rust and other factors, improving work efficiency.
■Used to remove and install the swingarm of scooters
■With a protector to protect the shaft
■Assembly in accordance with the step of the suspension part
■Special bolt to withstand high torque
■Remove the axle nut and check if the swingarm can be removed by hand.
■Tighten the puller bolt after confirming that each part has been assembled securely.
[Procedure]
[1]Remove the axle nut and check if the swingarm can be removed by hand.(Scope of Application: P.C.D up to 140-280mm)
[2] Make sure that each part is securely assembled and tighten the puller bolts.Bike assembly: PCX125
Catatan
* Gambar hanya untuk referensi. Gambar yang ditampilkan mungkin berbeda dari produk yang sebenarnya.
PRODUK YANG JUGA DILIHAT
Produk Siap Dikirim dari Gudang Jepang
Rekomendasi buat Kamu
Best Seller
New Custom Article
Gunakan kupon
Review Gambar
Review detail
/