- Beranda
- Motor
- HONDA 1001cc -
- CB1300SB (Super Bol D'or, CB1300S)
- Sparepart Motor
- Kelistrikan
- Lampu
- Sparepart Lampu Sein Lainnya
- CF POSH
- CF POSH: Papan Lampu Sein Sequential LED Tipe B
Papan Lampu Sein Sequential LED Tipe B
- Nomor produk: 660980-10
-
- IN STOCK
- Out Stock
- CF POSH
- |
- 5.0
- (1 ulasan)
Cek kupon saya
Jumlah
100% Ori
Garansi 7 hr
Gratis Cashback
Nett Tanpa Biaya Tambahan
Model yang Sesuai
Lihat SemuaRincian Produk
Konten ini diterjemahkan oleh Google, jika Anda ingin melihat aslinya, silakan klik
Lihat versi asli
Spesifikasi:
High luminosity LED x 24pcs
[Termasuk]
1. Papan LED sequential
Untuk lampu sein depan dan belakang / 2 kabel 120° tipe pin........ 4pcs
2.Baut tapping M3 x 30 4pcs
3. Spacer plastik 4pcs
4. Washer nylon untuk baut tapping 4pcs High luminosity LED x 24pcs
[Components]
1. LED customizing board sequential type assy
For front and rear blinkers / 2-wire 120° Pin Type........ 4pcs
2.Tapping screw M3 x 30 4pcs
3. Plastic spacer 4pcs
4. Nylon Washer for Tapping 4pcs
[Termasuk]
1. Papan LED sequential
Untuk lampu sein depan dan belakang / 2 kabel 120° tipe pin........ 4pcs
2.Baut tapping M3 x 30 4pcs
3. Spacer plastik 4pcs
4. Washer nylon untuk baut tapping 4pcs High luminosity LED x 24pcs
[Components]
1. LED customizing board sequential type assy
For front and rear blinkers / 2-wire 120° Pin Type........ 4pcs
2.Tapping screw M3 x 30 4pcs
3. Plastic spacer 4pcs
4. Nylon Washer for Tapping 4pcs
[Deskripsi]
Untuk kendaraan dengan satu lampu sein depan dan lampu posisi.
Sinyal belok sekuensial LED untuk diintegrasikan ke dalam sinyal belok saham. Untuk kendaraan standar yang sudah memiliki lampu sein LED, ini adalah set PCB tanpa relai sinyal belok khusus. For vehicles with a single front blinker bulb and a position lamp.
LED sequential (chain) blinkers that can be integrated into the stock blinkers.
A set of circuit boards without dedicated indicator relays for compatible vehicles that already have LED blinker lights.
Sinyal belok sekuensial LED untuk diintegrasikan ke dalam sinyal belok saham. Untuk kendaraan standar yang sudah memiliki lampu sein LED, ini adalah set PCB tanpa relai sinyal belok khusus. For vehicles with a single front blinker bulb and a position lamp.
LED sequential (chain) blinkers that can be integrated into the stock blinkers.
A set of circuit boards without dedicated indicator relays for compatible vehicles that already have LED blinker lights.
Peringatan
*Siklus seinnya tidak sesuai dengan relay sein LED. Perlu membeli relay lampu CF Posh.
*Harap diperhatikan bahwa spesifikasi produk dapat berubah karena alasan produsen.
•Perihal lampu sein•
1. Siklus 1 detik-0.5 detik
(Lebih dari 60 kali dan kurang dari 120 per menit / Produk mengedip 73-75 kali per menit)
2. Ketentuan ini harus dipenuhi ketika cahaya sein dibuat oleh pencahayaan berantai
(1) Tiap sumber lampu harus menyala sampai di akhir sirklus ON setelah dinyalakan.
(2) Pencahayaan lampu berantai atau berserti terjadi secara seragam dari luar atau samping.
(3) Tikda ada alternasi repetitif di arah vertikal (garis lurus menyambung)
(4) Variasi selesai dalam 200ms setelah siklus ON dinyalakan. *If the flashing cycle is not compatible with the LED blinker relay, it will not work properly.CF POSH blinker relays must be purchased separately and the blinker relays must be replaced.
*There may be changes in product specifications due to the manufacturer's reasons.
■□■Regarding Sequential blinker specifications■□■
1. cycle 1sec-0.5sec
(More than 60 times per minute and less than 120 times per minute / Product flashes 73-75 times per minute)
2. the following conditions must be met when flashing light sources are produced by chain lighting
(1) Each light source remains lit until the end of the ON cycle after it is turned on.
(2) The lighting of the series of light sources occurs uniformly and progressively from the inner to the outer edge of the apparent surface.
(3) No repetitive alternation in the vertical direction (e.g: A single continuous line (without waves).
(4) The variation ends within 200ms after the start of the ON cycle.
*Harap diperhatikan bahwa spesifikasi produk dapat berubah karena alasan produsen.
•Perihal lampu sein•
1. Siklus 1 detik-0.5 detik
(Lebih dari 60 kali dan kurang dari 120 per menit / Produk mengedip 73-75 kali per menit)
2. Ketentuan ini harus dipenuhi ketika cahaya sein dibuat oleh pencahayaan berantai
(1) Tiap sumber lampu harus menyala sampai di akhir sirklus ON setelah dinyalakan.
(2) Pencahayaan lampu berantai atau berserti terjadi secara seragam dari luar atau samping.
(3) Tikda ada alternasi repetitif di arah vertikal (garis lurus menyambung)
(4) Variasi selesai dalam 200ms setelah siklus ON dinyalakan. *If the flashing cycle is not compatible with the LED blinker relay, it will not work properly.CF POSH blinker relays must be purchased separately and the blinker relays must be replaced.
*There may be changes in product specifications due to the manufacturer's reasons.
■□■Regarding Sequential blinker specifications■□■
1. cycle 1sec-0.5sec
(More than 60 times per minute and less than 120 times per minute / Product flashes 73-75 times per minute)
2. the following conditions must be met when flashing light sources are produced by chain lighting
(1) Each light source remains lit until the end of the ON cycle after it is turned on.
(2) The lighting of the series of light sources occurs uniformly and progressively from the inner to the outer edge of the apparent surface.
(3) No repetitive alternation in the vertical direction (e.g: A single continuous line (without waves).
(4) The variation ends within 200ms after the start of the ON cycle.
PRODUK YANG JUGA DILIHAT
Produk Siap Dikirim dari Gudang Jepang
Rekomendasi buat Kamu
Best Seller
New Custom Article
Gunakan kupon
Review Gambar
Review detail
/