- Beranda
- Motor
- HONDA 251 - 400cc
- NS400
- Sparepart Motor
- Sparepart Mesin
- Radiator
- Radiator
- Water Pump
- DMR-JAPAN
- DMR-JAPAN: Mechanical Seal Overhaul Kit
Cek kupon saya
Jumlah
100% Ori
Garansi 7 hr
Gratis Cashback
Nett Tanpa Biaya Tambahan
Model yang Sesuai
Lihat SemuaRincian Produk
Konten ini diterjemahkan oleh Google, jika Anda ingin melihat aslinya, silakan klik
Lihat versi asli
Spesifikasi:
[Daftar Produk]
SEAL MEKANIK
Bantalan Poros
Segel Minyak Poros
O-ring untuk Cover
Cincin-O Bagian Penyisipan Mesin [Product Description]
・Mechanical seal
・Bearings for shafts
・Oil seal for shaft
・O-ring for cover
・O-ring of the engine insertion part
SEAL MEKANIK
Bantalan Poros
Segel Minyak Poros
O-ring untuk Cover
Cincin-O Bagian Penyisipan Mesin [Product Description]
・Mechanical seal
・Bearings for shafts
・Oil seal for shaft
・O-ring for cover
・O-ring of the engine insertion part
[Deskripsi]
Ia memiliki semua bagian internal yang diperlukan yaitu OH ..
[Bagaimana cara menginstall]
1) Lakukan pemanasan dengan heat gun untuk melonggarkan pin knockout dengan perbedaan ekspansi termal.
2) Ketuk secara merata searah bukaan dengan plastisin untuk membukanya ..
3) Pastikan untuk menggunakan mesin press hidrolik, karena ini bukan tekanan yang bisa dilepaskan dengan memukulnya dengan palu ..
4) Periksa apakah impeler tidak mengganggu alas lalu tarik keluar dengan memberikan tekanan ..
6) Toleransi antara poros dan roda gigi cukup ketat, jadi gunakan oli sebelum pemasangan tekan ..
7) Masukkan roda gigi ke 37,4mm dari ujung poros.. Lebih mudah bekerja jika Anda membuat kerah sepanjang 37,4mm untuk menghindari mendorongnya terlalu jauh .. DMR-JAPAN original parts
Internal parts required for OH are included in this set!
[mounting instructions]
1. Heat up with a heat gun to loosen the knock pin by thermal expansion difference
2. Open the door by tapping it evenly in the direction of opening with a plastic hammer.
3. It is not a pressure that can be removed by hammering, so be sure to work with a hydraulic press.
4. Check that the impeller does not interfere with the base, and then pull it out by applying pressure.
6. Since the tolerance between the shaft and gear is large, it is quite tight, so please apply oil before press fitting.
7. Press-fit the gear up to 37.4mm from the end face of the shaft.It is recommended to make the collar 37.4mm long to avoid pushing it in too far.
[Bagaimana cara menginstall]
1) Lakukan pemanasan dengan heat gun untuk melonggarkan pin knockout dengan perbedaan ekspansi termal.
2) Ketuk secara merata searah bukaan dengan plastisin untuk membukanya ..
3) Pastikan untuk menggunakan mesin press hidrolik, karena ini bukan tekanan yang bisa dilepaskan dengan memukulnya dengan palu ..
4) Periksa apakah impeler tidak mengganggu alas lalu tarik keluar dengan memberikan tekanan ..
6) Toleransi antara poros dan roda gigi cukup ketat, jadi gunakan oli sebelum pemasangan tekan ..
7) Masukkan roda gigi ke 37,4mm dari ujung poros.. Lebih mudah bekerja jika Anda membuat kerah sepanjang 37,4mm untuk menghindari mendorongnya terlalu jauh .. DMR-JAPAN original parts
Internal parts required for OH are included in this set!
[mounting instructions]
1. Heat up with a heat gun to loosen the knock pin by thermal expansion difference
2. Open the door by tapping it evenly in the direction of opening with a plastic hammer.
3. It is not a pressure that can be removed by hammering, so be sure to work with a hydraulic press.
4. Check that the impeller does not interfere with the base, and then pull it out by applying pressure.
6. Since the tolerance between the shaft and gear is large, it is quite tight, so please apply oil before press fitting.
7. Press-fit the gear up to 37.4mm from the end face of the shaft.It is recommended to make the collar 37.4mm long to avoid pushing it in too far.
Peringatan
*There may be changes in product specifications due to the manufacturer's reasons.
*Inspect the sliding parts of the mechanical seal for damage before assembly.There is no warranty after installation. *There may be changes in product specifications due to the manufacturer's reasons.
*Inspect the sliding parts of the mechanical seal for damage before assembly.There is no warranty after installation.
*Inspect the sliding parts of the mechanical seal for damage before assembly.There is no warranty after installation. *There may be changes in product specifications due to the manufacturer's reasons.
*Inspect the sliding parts of the mechanical seal for damage before assembly.There is no warranty after installation.
PRODUK YANG JUGA DILIHAT
Produk Siap Dikirim dari Gudang Jepang
Rekomendasi buat Kamu
Best Seller
New Custom Article
Gunakan kupon
Review Gambar
Review detail
/