Konten ini diterjemahkan oleh Google, jika Anda ingin melihat aslinya, silakan klik
Lihat versi asli
Spesifikasi:
[Daftar Produk] lanjutkan ke HI (Harness gabungan)
Wide pulley installation support item
[Deskripsi]
Item Pendukung Lampiran Katrol Lebar "HI ni Susumikun Ini adalah suku cadang asli DMR-JAPAN! Ini adalah harness joint perawatan yang memungkinkan Anda untuk memindahkan katrol motor servo ke HI saat mesin mati! Sangat mudah untuk mengatur katup RC dan memasang katrol lebar dan katrol eksternal DMR .. Toko pro juga memujinya sebagai "ide bagus! Ini adalah permata dari produk yang telah dipuji oleh toko pro sebagai" Ide bagus!
Cara menggunakan] Lepaskan coupler dari katup RC dan masukkan smoothie ke katup HI.
DMR-JAPAN original parts.
This is a joint harness for maintenance that allows you to move the servo motor pulley to HI while the engine is stopped! It is very easy to adjust the RC valve and install DMR wide pulley or aftermarket pulley. Even the pro shop said "Good idea!"This is a gem of a product that has been praised by many!
[Click here to see a video of how to use it] Just remove only the coupler (white) on the RC valve and interrupt Mr. Susumu to HI and you're good to go!
[Adjustment method] (1) Remove the exhaust. (2) Move the Servo Motor to HI with Susumu-kun. (3) Adjust the RC valve (hereinafter referred to as "flap") to be a little more open than the exhaust port and tighten the nut lightly. (4) Push the cable on the return of the pulley with your finger to tension the cable on the pull side and lower the flap. (5) The harder you push the cable, the more strongly the cable on the pull side is stretched and the lower the flap.What this work implies is that the state in which the flaps are in a state of trueness is the tension strength of the cable at the time of finishing. (6) Once the desired tensioning strength has been determined where the flap is flush with the fender and wheel face, tighten the nut on the pull side. (7) Adjust the cable on the return side so that the flap is in alignment. (8) Oh, my wonder!I was able to adjust in one shot using the tension I expected ( 。・_・。.) people (.・_・。.) Yay!
Peringatan
* Setelah bekerja, harap hapus Susumu-kun. * Untuk pencegahan korsleting secara kebetulan, lakukan desorpsi bodi utama dengan sakelar MATI. * Ketika kunci kartu MC28 dalam keadaan ON dan penggandeng motor servo dilepaskan selama sekitar 10 detik, Kesalahan 2 ditampilkan. * Karena Susumu-kun memiliki resistor bawaan, pembengkokan dan peregangan yang tidak masuk akal dapat menyebabkan pemutusan sambungan, jadi harap pertimbangkan. * Ini bukan untuk pemeriksaan pengoperasian PGM dan motor servo.
*To prevent short-circuiting, please turn off the main switch when removing and installing Susumu-kun. *After the work, please remove Susumu-kun. *With the MC28, if the servo motor coupler is disconnected for about 10 seconds with the card key ON, error 2 will be displayed and the motor will not respond, but turning it OFF will release the error. *If the throttle position sensor is activated to the LO side, you may have forgotten to install the throttle position sensor or it may be broken. *Because a resistor is built into the Susumu-Kun, excessive bending and stretching will lead to disconnection.If the wire is broken, it will malfunction to the LO side. *Not for checking the operation of PGM or servomotor. *There may be changes in product specifications due to the manufacturer's reasons.
