Cek kupon saya
Jumlah
100% Ori
Garansi 7 hr
Gratis Cashback
Nett Tanpa Biaya Tambahan
Model yang Sesuai
Lihat Semua
Rincian Produk
Konten ini diterjemahkan oleh Google, jika Anda ingin melihat aslinya, silakan klik
Lihat versi asli
Spesifikasi:
[Spek]
Tegangan: DC12V
Ukuran diameter luar: W25.5mmXH30.5mmXD15.5mm
*tidak termasuk bagian yang menonjol)
[Isi produk]
Main unit SPI-110 C1 x1
Kabel harness untuk model motor khususx 1
Beragam double tape
Manual pemasangan
*Isi produk dapat beragam tergantung serinya.
Tegangan: DC12V
Ukuran diameter luar: W25.5mmXH30.5mmXD15.5mm
*tidak termasuk bagian yang menonjol)
[Isi produk]
Main unit SPI-110 C1 x1
Kabel harness untuk model motor khususx 1
Beragam double tape
Manual pemasangan
*Isi produk dapat beragam tergantung serinya.
[Deskripsi]
Meter to display the shift position while riding.
A kit for specific models.
All the parts you need for installation are ALL in ONE.
Shift data has been registered.
●Easy installation with special harness!
The special harness is designed for specific model, so you can install it easily without any soldering work.
*The vehicle-specific harness has a 12V (+) service terminal for easy installation of the CS-550 burglar alarm.
●Compact design!
The main unit dimensions are W25.5mm x H30.5mm x D15.5mm (excluding protruding parts), a compact design that does not interfere with installation around the meter.
●LED display for high visibility!
With a dimmer sensor on the entire surface [automatic dimming function]).The brightness of the LED is automatically adjusted to be brighter in the daytime and darker at night to improve the visibility of the digital numerals.
●Equipped with a shift up indicator!
With a dimmer sensor on the entire surface, you can set the rotation speed arbitrarily to prevent over-revving.The blue LED will light up when the rotation is higher than the set value.
*You can re-register as many times as you like.
The special harness is connected to the harness 16P coupler on the back of the meter.
Approx. 30 minutes of work
Q&A
Q. When the vehicle key is turned on or the engine is started, the display does not show (LED light does not light up)
A. The positive wire or the negative wire may have poor contact.Check the wiring again.
Q. When setting the gear position, "5" is displayed
A. The display of "5" means "S", and there is a case that the speedometer signal is not taken.After pushing the switch on the back of the unit three times, the shift lamp will blink "S" immediately after you put the unit into first gear, but if you start riding and the blinking "S" and the shift lamp disappear and the blinking dot appears and changes to the display of "1" a few seconds later, the unit has been registered without any problem.If the S display continues to appear after you start running, please refer to the following.
For electric speedometers, check that the wiring is correctly connected to the speedometer wire.Also, make sure that there is no poor contact between the wires.
In the case of a mechanical (cable) speedometer, check that the wiring from the optional PG-110 is correctly connected to the speed wire of the SPI-110.Also, make sure that there is no poor contact between the wires.Please make sure that the distance between the sensor and the magnet is within 3 to 5mm because "S" may appear if the PG-110 is installed incorrectly.Also, make sure that the passage point of each magnet passes through the blue circle sticker attached to the sensor of PG-110.
Q.When setting the gear position, "R" is displayed.
A. The "R" display indicates that no engine speed signal is being received.Check that the wiring is correctly connected to the tachometer signal wire.Also, make sure that there is no poor contact between the wires.
Q.When setting the gear position, "F" is displayed.
A1. While driving, both the speedometer signal and the engine speed signal are not being obtained.Check the contact of each wire and the installation method.
A2. When the key is turned ON in a gear other than neutral, "F" will blink.In this case, put the vehicle in neutral gear and turn the key from OFF to ON, so that "F" will not be displayed.
A3. If "F" flashes even when the key is turned ON in neutral gear, the green wire of the shift indicator is not connected properly.Check the wiring diagram and connect it to the neutral switch.
A kit for specific models.
All the parts you need for installation are ALL in ONE.
Shift data has been registered.
●Easy installation with special harness!
The special harness is designed for specific model, so you can install it easily without any soldering work.
*The vehicle-specific harness has a 12V (+) service terminal for easy installation of the CS-550 burglar alarm.
●Compact design!
The main unit dimensions are W25.5mm x H30.5mm x D15.5mm (excluding protruding parts), a compact design that does not interfere with installation around the meter.
●LED display for high visibility!
With a dimmer sensor on the entire surface [automatic dimming function]).The brightness of the LED is automatically adjusted to be brighter in the daytime and darker at night to improve the visibility of the digital numerals.
●Equipped with a shift up indicator!
With a dimmer sensor on the entire surface, you can set the rotation speed arbitrarily to prevent over-revving.The blue LED will light up when the rotation is higher than the set value.
*You can re-register as many times as you like.
The special harness is connected to the harness 16P coupler on the back of the meter.
Approx. 30 minutes of work
Q&A
Q. When the vehicle key is turned on or the engine is started, the display does not show (LED light does not light up)
A. The positive wire or the negative wire may have poor contact.Check the wiring again.
Q. When setting the gear position, "5" is displayed
A. The display of "5" means "S", and there is a case that the speedometer signal is not taken.After pushing the switch on the back of the unit three times, the shift lamp will blink "S" immediately after you put the unit into first gear, but if you start riding and the blinking "S" and the shift lamp disappear and the blinking dot appears and changes to the display of "1" a few seconds later, the unit has been registered without any problem.If the S display continues to appear after you start running, please refer to the following.
For electric speedometers, check that the wiring is correctly connected to the speedometer wire.Also, make sure that there is no poor contact between the wires.
In the case of a mechanical (cable) speedometer, check that the wiring from the optional PG-110 is correctly connected to the speed wire of the SPI-110.Also, make sure that there is no poor contact between the wires.Please make sure that the distance between the sensor and the magnet is within 3 to 5mm because "S" may appear if the PG-110 is installed incorrectly.Also, make sure that the passage point of each magnet passes through the blue circle sticker attached to the sensor of PG-110.
Q.When setting the gear position, "R" is displayed.
A. The "R" display indicates that no engine speed signal is being received.Check that the wiring is correctly connected to the tachometer signal wire.Also, make sure that there is no poor contact between the wires.
Q.When setting the gear position, "F" is displayed.
A1. While driving, both the speedometer signal and the engine speed signal are not being obtained.Check the contact of each wire and the installation method.
A2. When the key is turned ON in a gear other than neutral, "F" will blink.In this case, put the vehicle in neutral gear and turn the key from OFF to ON, so that "F" will not be displayed.
A3. If "F" flashes even when the key is turned ON in neutral gear, the green wire of the shift indicator is not connected properly.Check the wiring diagram and connect it to the neutral switch.
Peringatan
*Kelengkapan produk berbeda-beda tergantung paketnya.
*Jika Anda menahan kopling saat berkendara, display selain gigi yang diaktifkan akan muncul, tapi hal ini bukan kerusakan produk.
*Saat berkendara, utamakan keselamatan dan jangan ceroboh di jalan.
*Saat menggunakannya di jalan umum, harap berkendara sesuai dengan aturan lalu lintas.
*Jangan gunakan busi tanpa resistor. Jika Anda menggunakan busi tanpa resistor, suara bising dapat muncul dan sinyal rotasi mungkin tidak masuk dengan benar. Oleh karena itu, gunakan busi dengan resistor.
*Karena ada saklar di bagian belakang produk ini, pasang double-tape untuk mencegah air masuk.
*Saat memasang produknya, ikuti instruksi manual untuk memasang dengan benar. Pemasangan yang salah dapat menyebabkan kebakaran atau kerusakan produk.
*Setelah memasang produk ini, periksa secara teratur untuk melihat apakah ada bagian yang terlepas.
*Harap dicatat bahwa produsen tidak bertanggung jawab atas segala kerusakan seperti malfungsi atau kecelakaan yang disebabkan oleh penggunaan produk ini.
*Harap diperhatikan bahwa produsen juga tidak bertanggung jawab atas biaya desorpsi dan biaya lain yang timbul selama perbaikan produknya.
*Semua motor yang kesesuaiannya telah dikonfirmasi oleh produsen adalah motor standar keluaran pabrikan. Masalah dapat terjadi pada motor yang dilengkapi dengan sparepart aftermarket.
*Saat memasang produknya, pastikan untuk memeriksa setiap kabel di manual servis motor Anda.
*Harap diperhatikan bahwa spesifikasi produk mungkin berubah karena alasan produsen.
*Jika Anda menahan kopling saat berkendara, display selain gigi yang diaktifkan akan muncul, tapi hal ini bukan kerusakan produk.
*Saat berkendara, utamakan keselamatan dan jangan ceroboh di jalan.
*Saat menggunakannya di jalan umum, harap berkendara sesuai dengan aturan lalu lintas.
*Jangan gunakan busi tanpa resistor. Jika Anda menggunakan busi tanpa resistor, suara bising dapat muncul dan sinyal rotasi mungkin tidak masuk dengan benar. Oleh karena itu, gunakan busi dengan resistor.
*Karena ada saklar di bagian belakang produk ini, pasang double-tape untuk mencegah air masuk.
*Saat memasang produknya, ikuti instruksi manual untuk memasang dengan benar. Pemasangan yang salah dapat menyebabkan kebakaran atau kerusakan produk.
*Setelah memasang produk ini, periksa secara teratur untuk melihat apakah ada bagian yang terlepas.
*Harap dicatat bahwa produsen tidak bertanggung jawab atas segala kerusakan seperti malfungsi atau kecelakaan yang disebabkan oleh penggunaan produk ini.
*Harap diperhatikan bahwa produsen juga tidak bertanggung jawab atas biaya desorpsi dan biaya lain yang timbul selama perbaikan produknya.
*Semua motor yang kesesuaiannya telah dikonfirmasi oleh produsen adalah motor standar keluaran pabrikan. Masalah dapat terjadi pada motor yang dilengkapi dengan sparepart aftermarket.
*Saat memasang produknya, pastikan untuk memeriksa setiap kabel di manual servis motor Anda.
*Harap diperhatikan bahwa spesifikasi produk mungkin berubah karena alasan produsen.
