Kembali ke atas

【KITACO】Satu Set Manifold

Harga: Rp1,078,000

*Termasuk PPN 10%

Nikmati cicilan 0% mulai dari Rp89,833/bulan

Webike Points: 10,780 pts

Shipping point: 6 pts ( 6 pts x 1qty)
Ubah
DKI Jakarta, Jakarta Selatan, Cilandak
Biaya pengiriman
Rp9,000

    • Nomor Produk:
    • 410-1020328

Mohon tunggu...


Model yang Sesuai:

CHALY 50

CHALY70 [CHALY]

Lihat lebih lanjut

Rincian Produk

Konten ini diterjemahkan oleh Google, jika Anda ingin melihat aslinya, silakan klik Lihat versi asli

[Spesifikasi]

untuk PWKΦ28
untuk sepeda motor dengan kepala silinder ULTRA-SE KITACO
Bahan: Aluminium Casting
Diameter Port: Sesuai untuk Φ26.
dengan karet dudukan eksklusif

[Deskripsi]


Chaly 50 / 70 (Mobil ULTRA-SEHead dilengkapi dibuat oleh Kitaco) Desain eksklusif.
Set 2Type untuk MikuniVMΦ26 dan KEIHINPWKΦ28. Bingkai dipasang tanpa melampirkan, Sekrup dapat disesuaikan.

[Catatan]


* Tidak dapat menginstal Pusat Penutup.
* Karburator atau Throttle kabel dll. secara terpisah diperlukan.
* Gambar yang ditampilkan adalah hanya untuk referensi. gambar mungkin berbeda dari produk yang sebenarnya.

* Informasi dari produsen.

untuk daya asupan efisien !!

Mengetik :
pwkΦ28

Deskripsi :
set berjenis untuk Chaly 50 / 70. satu adalah untuk Mikuni vm Φ26 karburator. yang lain adalah untuk pwkΦ28 karburator.
sekrup disesuaikan setelah instalasi tanpa bingkai modifikasi.

Catatan :
■ asupan pelabuhan o. D. Φ26-
* Karburator & throttle tinggi set (dijual terpisah) Wajib.
* Pusat saham penutup tidak dapat digunakan.

Model yang Sesuai

    • CHALY 50
    • CHALY70 [CHALY]
  • 3.8

    11 Ulasan

  • 5

    Memuaskan

    4

    4

    Bagus

    4

    3

    Lumayan

    1

    2

    Kurang

    1

    1

    Mengecewakan

    1
  • Tulis Ulasan

    Fantastic replacement for the stock intake on your Honda Spree NQ50 or Honda Aero SB50. This fits on the 2 bolt intake, non variated AF05 engine. I was able to bolt up a Polini CP carb by just using a coupler. In the following image, you see the Kitaco intake on the left, and a Spree intake on the right.

    I used it with C50 + PC20 but Accelerator Wire can not be attached as it is to buffer it in Frame.
    PowerfulSpec with swinging Spacer. Or NORMALAIR cleanerSpec. If you are stuck with it, you can not install it unless the carburetor itself protrudes forward by putting a thick Insulator or Spacer in the carburetor side attachment.
    I think that somehow it can be installed if Accelerator Wire can be machined into an L-shaped Top cap like PB.

    According to this Manifold (phi 22), expansion processing is carried out and I am using the inlet port of the Normal head of 12V(AB27) 88 cc of MONKEYs.A Power and a Response improve to the extent that it does not become a comparison to
    processing before.
    Incidentally it exceeds 90 by this specification.
    port processing is carried out and it is a Recommendation with value about PC20!

    It attached to KITACO Standard-head 88cc of the Webike Monitor

    MONKEY. Carburetor attachment became a Rubber holder for the change from
    KEIHIN PCphi20 Carburetor kit, and the Setting became easy.
    Since the diameter of a port was also diameter[ of a large ]-ized again, PE24 carburetor was matched and it led also to the remarkable Power up.

    Although it was a Manifold set for the Big carburetors of 24 pies of a Mikuni, it was used for PE24 of a KEIHIN.
    > attachment is easy, and if the Manifold currently attached from the first can be removed, it can be attached in a reverse procedure. Since the
    > Manifold will deteriorate easily if time passes with the parts of a Rubber, it is dramatically kind if only this part is sold (the product made from a KEIHIN does not have an option).

    [Webike Monitor] It purchased in order to equip the
    > GIORCUB with KEIHIN PC20. Although it can equip with the main part of

    CARBURETOR satisfactorily, the Air cleaner of a NORMAL and the position of a CARBURETOR stop suiting at all. Since
    > one wanted to use the Air cleaner of a NORMAL, he converted a few. The mounting surface by the side of the Engine of the
    Manifold is deleted aslant, and it was made for the angle of a CARBURETOR to fall for a while. The Nozzle of the Drain of an Engine and the CARBURETOR in which it interferes, and the extending pipe of a Cut and their original work at the entrance of an Air cleaner were then attached.

    I think that I will unite with the path of a Manifold and will delete an air supply port when there is when or time.

11 Ulasan Lihat semua

Produk Teratas

【SP Takegawa】Big Throttle Body Kit
Big Throttle Body Kit SP Takegawa
【FORK】Carburetor Top Cover
Cover Atas Karburator FORK
【KITACO】Manifold Set
Satu Set Manifold KITACO
【SP Takegawa】Manifold Adapter Set
Satu Set Adaptor Manifold SP Takegawa
【POSH】Breather Plate
Plat Breather POSH
【SP Takegawa】Multi Manifold Kit
Multi Manifold Kit SP Takegawa
【KITACO】Manifold Set
Satu Set Manifold KITACO
【YOSHIMURA】Manifold Kit for YD28 GROM
Set Manifold untuk YD28 GROM YOSHIMURA