Check my coupons
Product Detail
Specification:
Swingarm pipe shape: triple square
Stabilizer: Without
Material: Aluminum 7N01 material used
Stabilizer: Without
Material: Aluminum 7N01 material used
[Description]
Swingarm Weight: Stock 3.5kg→1.8kg (for GROM, triple square, no sway bar, +0cm)
The swingarm is made of aluminum 7N01 material and it is 1.8kg lighter than stock swingarm 3.5kg.
■Option Description
[Swingarm finish]
・Black anodized finish (G-Craft part number: 60198)
・Cerakote finish (G-Craft part number: 60807)
[What is Cerakote?]
Cerakote is a special heat coloring and normal temperature paint manufactured by NIC and currently used by the US military.
It has been inspected to meet the harsh conditions, and has excellent heat resistance, abrasion resistance, durability, solvent resistance, heat dissipation, heat insulation and other performance-oriented research and production.
Ceramic is crushed by a special machine and mixed into the paint to improve the strength of the paint film.Therefore, the surface becomes pear-shaped, but the coating film can be made very thin (25 microns)
Weld marks (beads) can be left on the surface without being hidden.
The adhesion is the highest among all coating materials, and the surface treatment is suitable for frames and swingarms because it does not wrinkle even when bent, and the paint does not peel off easily even by stepping stones.
*Please allow 3 to 5 weeks for normal delivery.
[Option 1] Chain slider bolt fixing specification (G-Craft part number:60228)
Change the chain slider from riveted to bolted.Easy to replace when worn out.
[Option 2] Pivot part bearing specification (G-Craft part number: 60006)
The standard is to change the pivot part of the bushing to a bearing.
Improved durability and smooth operating characteristics.
[Option 3] Stand hook base (M6) additional processing (G-Craft part number: 60903)
G-Craft stand hook or aftermarket stand hook (M6) can be attached.
[Option 4] Chain adjuster option
・Racing stand hook specification (G-Craft part number: 60186)
The rear part of the conventional chain pull can be used as a stand-hook.G-Craft Part Number: The 32071, 32072 and 32073 racing stand hooks can be installed.
*G Kraft Part Number:33170AP Lockheed caliper support cannot be installed (will interfere)
・Back pull type (G-Craft part number: 60221)
This backward pull adjuster is designed to eliminate the hassle of adjusting the chain.
Since the adjusting nut is located at the end of the swingarm, it is easy to adjust the adjusting part which was difficult to turn due to interference of tools
*Can not be installed on the racing stand hook specification and OW type at the same time
・OW type (G-Craft part number: 60014)
The chain puller is tapered to eliminate vertical misalignment of the axle shaft.
The tapered frame moves so there is no vertical misalignment.This mechanism is also used for swingarms of big bikes.
・OW type racing stand hook specification (G-Craft part number: 60188)
The rear part of OW type chain pull is changed to stand hook specification.
G-Craft Part Number: The 32071, 32072 and 32073 racing stand hooks can be installed.
*G Kraft Part Number:33170AP Lockheed caliper support cannot be installed (will interfere)
・Eccentric type (G-Craft part number: 60059)
This is an eccentric type chain puller commonly found on Kawasaki motorcycles.
*Only caliper supports with calipers attached to the lower part of the swingarm can be used on disc models.
Note
Click here for other Cub swing arms.
Click here for option stand hooks for racing stand hook specifications
* The image is only for reference. The image shown may differ from the actual product.
Caution
*Image 1 shows the pipe shape: Standard
*Image 3 is an image of the swingarm finish option.
1・Black anodized finish / 2・Ceracoat finish
*Image 4 is an image of Option 1: Chain Slider.
*Image 5 is an image of Option 2: Pipot bearing processing.
*Image 6 is an image of Option 3: Additional processing of the stand hook base.
*Image 7 is an image of Option 4: Chain pull type.
1・Back pull type
2・Standard type (Racing stand hook specification)
3・OW type (Racing stand hook specification)
4・Eccentric type
*Image 3 is an image of the swingarm finish option.
1・Black anodized finish / 2・Ceracoat finish
*Image 4 is an image of Option 1: Chain Slider.
*Image 5 is an image of Option 2: Pipot bearing processing.
*Image 6 is an image of Option 3: Additional processing of the stand hook base.
*Image 7 is an image of Option 4: Chain pull type.
1・Back pull type
2・Standard type (Racing stand hook specification)
3・OW type (Racing stand hook specification)
4・Eccentric type
Applicable Models
CUB90
