Heat Resistant Motorcycle Cover Half Type for Vehicles with Side Box
- Product number: BB-711
- unicar
- |
- 3.0
- (1 reviews)
Check my coupons
Product Detail
Specification:
■Type SB
With side BAG
Size: Overall length 250 x Overall height 155 x Overall width 115 x Tail width upper 85 x Tail width lower 85 x Tail height 105cm
Exclusive for vehicles equipped with side box
Comes with a storage bag
Rear hem tie with rope
With side BAG
Size: Overall length 250 x Overall height 155 x Overall width 115 x Tail width upper 85 x Tail width lower 85 x Tail height 105cm
Exclusive for vehicles equipped with side box
Comes with a storage bag
Rear hem tie with rope
[Description]
There are many people who have had the experience of melting a conventional body cover when it was applied to a hot exhaustThis non-melting motorcycle cover is perfect for anyone who has ever experienced this.It is effective not only for exhaust but also for engine heat.Other than the fact that it doesn't melt, it is made with great care and attention to detail.The outer surface of this bike cover is made of thick ox 300D fabric for practicality and durability.A one-touch anti-flying belt is attached to the center part.In addition, there are four large keyholes in the front and rear that can be fitted with locks of 70mm diameter, so that the front and rear can be distinguished by color.You don't need to spread out the bag to check which side is the front, and it is also highly effective in preventing both theft and wind skipping.
Only for motorcycles with side boxes
Product dimensions / Exclusively for bikes equipped with side boxes
Rear hem tie with rope
Only for motorcycles with side boxes
Product dimensions / Exclusively for bikes equipped with side boxes
Rear hem tie with rope
Note
* The image is only for reference. The image shown may differ from the actual product.
Caution
*The surface melts in the heat.Please be careful when covering.
*The shape of the body of a motorcycle varies greatly depending on the model.The dimensions shown are for reference only.
*The product may not be applicable to some models and years.
*If your vehicle is not listed in the application chart, please refer to the dimensions of each part or contact us.
*We do not accept returns after opening the package or installation.
*The cover article is waterproofed on the surface, but because it is sewn, rainwater may penetrate through the seams.Not fully waterproof.
*The lifetime of the cover depends on the climate and operating conditions.Regardless of the period of use, if the water repellency of the cover decreases significantly, it is the end of its life and you should purchase a new product.
*Be sure to remove the wet cover and dry both the bike and the bike cover before use.Leaving the paint on the surface for a long time can damage the surface of the paint and cause rust and mildew.
*When repainting, make sure that the paint is sufficiently dry before covering.(Dry for 3 months for normal paint and 6 months for metallic paint.)
*In case of strong wind, there is a possibility that the wind chill may enter into the bike cover, so please take enough care of it including prevention of falling.
*We are not responsible for any accidents caused by inadequate use or natural disasters (typhoons, etc.).
*There may be changes in product specifications due to the manufacturer's reasons.
*The shape of the body of a motorcycle varies greatly depending on the model.The dimensions shown are for reference only.
*The product may not be applicable to some models and years.
*If your vehicle is not listed in the application chart, please refer to the dimensions of each part or contact us.
*We do not accept returns after opening the package or installation.
*The cover article is waterproofed on the surface, but because it is sewn, rainwater may penetrate through the seams.Not fully waterproof.
*The lifetime of the cover depends on the climate and operating conditions.Regardless of the period of use, if the water repellency of the cover decreases significantly, it is the end of its life and you should purchase a new product.
*Be sure to remove the wet cover and dry both the bike and the bike cover before use.Leaving the paint on the surface for a long time can damage the surface of the paint and cause rust and mildew.
*When repainting, make sure that the paint is sufficiently dry before covering.(Dry for 3 months for normal paint and 6 months for metallic paint.)
*In case of strong wind, there is a possibility that the wind chill may enter into the bike cover, so please take enough care of it including prevention of falling.
*We are not responsible for any accidents caused by inadequate use or natural disasters (typhoons, etc.).
*There may be changes in product specifications due to the manufacturer's reasons.