Check my coupons
Quantity
100% Original
7 Days Warranty
Free Cashback
Net Price
Applicable Models
See All
Super Cub 110 Pro 18-21
Product Detail
Specification:
Rated Voltage: DC12V
Power consumption: Hi beam 20W / Lo beam 20W
Color Temperature: 6000 Kelvin
LED: CREE XLamp XP-L LEDs
Country of origin :Japan
Power consumption: Hi beam 20W / Lo beam 20W
Color Temperature: 6000 Kelvin
LED: CREE XLamp XP-L LEDs
Country of origin :Japan
[Description]
Headlight kit to increase the brightness and look classic just by replacing the stock LED headlight of SUPER CUB 110 (18-) Pro.
Luminescence color is white 6000 Kelvin and halogen bulb color 3000 Kelvin.
All the necessary parts for installation are included.
Simply replace the stock headlight with this product's headlight and install the dedicated connection harness and controller.
■It is not only the design of the appearance but also the brightness of many times!
The Lo beam of the stock LED headlight emits light at 7.8W, which is not bright enough to illuminate the road surface.
By replacing with PROTEC's LED headlight, the brightness will be increased many times as shown in the comparison image.
The difference of the power consumption is 2.5 times, but you can feel the brightness more than 2.5 times.
■Do you feel that the stock LED headlights are too dim?
SUPER CUB / CROSS CUB (18-) stock LED headlight Lo beam is on at 7.8w.
If you look at the image that LED is brighter than conventional bulbs, you will be disappointed in the brightness of normal LED.
Unlike the bulb type headlight, the stock LED headlight can not be brightened by replacing with aftermarket LED.
By replacing the headlight unit, this product makes the headlight brighter many times.
As a result of PROTEC measurement, the difference of Candela value of Lo beam is more than 5 times!
■Clear multi-reflector lens
The stock standard LED headlight for the 18 model SUPER CUB 110 / 50 and CROSS CUB 110 / 50 is a multi-reflector type with no cut on the lens surface.
Have you ever felt that the LED base placed horizontally in the middle of the headlight is uncomfortable when viewed from the front?PROTEC products are finished with a clean look by adopting the familiar multi-reflector lens of the past.
■Available color temperatures are 6000K and 3000K
Please select your favorite color from two colors: 6000 Kelvin, which is a typical LED blue-white color, and 3000 Kelvin, which is a classic halogen bulb color.
■Hi beam is also bright!
The brightness is much brighter than stock LED headlights even when switched to Hi beam.
When the stock Hi beam is on, the Lo beam is also on at the same time.
Even when both Hi and Lo are lit at the same time, the brightness is very weak compared to PROTEC products.
■Hi beam indicator can be turned on!
By removing the stock LED headlight, the Hi beam indicator will no longer be illuminated, but PROTEC's unique control system allows the Hi beam indicator to be illuminated.
■Waterproof electric fan cooling
A really bright LED generates heat due to the large input current and becomes hot.
In order to cool down the heat, this product adopts a cooling system with a highly durable waterproof electric fan.
It is essential equipment to maintain stable brightness.
■Adoption of reliable CREE LED!
A total of 4 CREE XLamp XP-L LEDs (2 for Hi beam and 2 for Lo beam) are used as light emitters.
■Easy to install!Bolt-on
The tools required for installation are a + screwdriver (large or small) and pliers.
How to remove and install the cowl is clearly explained with color pictures in the instruction manual.
Luminescence color is white 6000 Kelvin and halogen bulb color 3000 Kelvin.
All the necessary parts for installation are included.
Simply replace the stock headlight with this product's headlight and install the dedicated connection harness and controller.
■It is not only the design of the appearance but also the brightness of many times!
The Lo beam of the stock LED headlight emits light at 7.8W, which is not bright enough to illuminate the road surface.
By replacing with PROTEC's LED headlight, the brightness will be increased many times as shown in the comparison image.
The difference of the power consumption is 2.5 times, but you can feel the brightness more than 2.5 times.
■Do you feel that the stock LED headlights are too dim?
SUPER CUB / CROSS CUB (18-) stock LED headlight Lo beam is on at 7.8w.
If you look at the image that LED is brighter than conventional bulbs, you will be disappointed in the brightness of normal LED.
Unlike the bulb type headlight, the stock LED headlight can not be brightened by replacing with aftermarket LED.
By replacing the headlight unit, this product makes the headlight brighter many times.
As a result of PROTEC measurement, the difference of Candela value of Lo beam is more than 5 times!
■Clear multi-reflector lens
The stock standard LED headlight for the 18 model SUPER CUB 110 / 50 and CROSS CUB 110 / 50 is a multi-reflector type with no cut on the lens surface.
Have you ever felt that the LED base placed horizontally in the middle of the headlight is uncomfortable when viewed from the front?PROTEC products are finished with a clean look by adopting the familiar multi-reflector lens of the past.
■Available color temperatures are 6000K and 3000K
Please select your favorite color from two colors: 6000 Kelvin, which is a typical LED blue-white color, and 3000 Kelvin, which is a classic halogen bulb color.
■Hi beam is also bright!
The brightness is much brighter than stock LED headlights even when switched to Hi beam.
When the stock Hi beam is on, the Lo beam is also on at the same time.
Even when both Hi and Lo are lit at the same time, the brightness is very weak compared to PROTEC products.
■Hi beam indicator can be turned on!
By removing the stock LED headlight, the Hi beam indicator will no longer be illuminated, but PROTEC's unique control system allows the Hi beam indicator to be illuminated.
■Waterproof electric fan cooling
A really bright LED generates heat due to the large input current and becomes hot.
In order to cool down the heat, this product adopts a cooling system with a highly durable waterproof electric fan.
It is essential equipment to maintain stable brightness.
■Adoption of reliable CREE LED!
A total of 4 CREE XLamp XP-L LEDs (2 for Hi beam and 2 for Lo beam) are used as light emitters.
■Easy to install!Bolt-on
The tools required for installation are a + screwdriver (large or small) and pliers.
How to remove and install the cowl is clearly explained with color pictures in the instruction manual.
Caution
*Please make sure to check the availability before you order.
*Install the product correctly according to the instruction manual.Improper installation may result in fire or equipment damage.
*Before installation, be sure to disconnect the terminal cord on the minus side of the battery and confirm that the key is OFF.
*Please do not touch or get the LED chip dirty.Dirt can cause the LED chip to burn due to heat being built-up.The LED bulb comes with an acrylic cap with a sealing seal.
*Please handle this product with care as it is a precision instrument.Do not drop the product or pull the wires forcibly.Improper handling may cause malfunction, injury, burns, or serious accidents that may result in death.In addition, sparks, poor insulation, or short-circuiting may cause a failure of the product or a fire in the vehicle.
*Do not disassemble or modify this product in any way.Products that have been disassembled or modified are not covered by warranty.
*Do not look directly at the LED light when it is on.It can cause visual impairment.
*Do not splash water on the lens while the light is on or immediately after it is turned off.Sudden temperature change may cause damage to the lens or LED bulb.In addition, please do not touch the LED bulb itself, the heat sink behind it, and the controller unit because they get to the high temperature.
*This product is for motorcycles only, so cannot be used on four-wheeled vehicles.This product is not for use on automobiles.
*Do not cover with paper or cloth and do not light near flammable materials.Failure to do so may result in fire or abnormal heating.Also, do not light near flammable items such as flammable spray, thinner, etc. or items that may ignite.
*Do not install to the headlight with the light on.Failure to do so may result in malfunction or burns.
*This product is waterproof for daily life, but it is not completely waterproof.Wrap the coupler coming out of the controller unit with vinyl tape or self-bonding tape, or use caulking agent to waterproof it.Avoid wetting the product with more water than necessary.
*When washing a vehicle with a high pressure washer, please do not let the high pressure wash directly hit this product.
*Please do not drop the LED bulb or controller unit, or give it a strong shock.It not only causes breakage, deterioration of performance and shortening of service life, but also causes injury.
*When assembling the LED bulb, be sure to apply the supplied silicon grease to the areas indicated by the grease marks in the instruction manual.
*Do not cover up the waterproof fan.Make sure that there is enough space behind the fan for the sucked air to flow.
*Use a thread locker to prevent loosening of the threaded part.Periodic retightening is also recommended.
*Installation requires expertise and skill.Please have it done at a designated maintenance facility with skilled mechanics.
*Please adjust the optical axis before use.It may obstruct the view of oncoming vehicles and cause traffic accidents.
*PROTEC is not responsible for any damage or accident caused by the use of this product.Protec will not be responsible for any labor charges or other costs incurred during repair.
*If you feel any abnormality during installation or use, please contact your dealer or PROTEC service department.
*Install the product correctly according to the instruction manual.Improper installation may result in fire or equipment damage.
*Before installation, be sure to disconnect the terminal cord on the minus side of the battery and confirm that the key is OFF.
*Please do not touch or get the LED chip dirty.Dirt can cause the LED chip to burn due to heat being built-up.The LED bulb comes with an acrylic cap with a sealing seal.
*Please handle this product with care as it is a precision instrument.Do not drop the product or pull the wires forcibly.Improper handling may cause malfunction, injury, burns, or serious accidents that may result in death.In addition, sparks, poor insulation, or short-circuiting may cause a failure of the product or a fire in the vehicle.
*Do not disassemble or modify this product in any way.Products that have been disassembled or modified are not covered by warranty.
*Do not look directly at the LED light when it is on.It can cause visual impairment.
*Do not splash water on the lens while the light is on or immediately after it is turned off.Sudden temperature change may cause damage to the lens or LED bulb.In addition, please do not touch the LED bulb itself, the heat sink behind it, and the controller unit because they get to the high temperature.
*This product is for motorcycles only, so cannot be used on four-wheeled vehicles.This product is not for use on automobiles.
*Do not cover with paper or cloth and do not light near flammable materials.Failure to do so may result in fire or abnormal heating.Also, do not light near flammable items such as flammable spray, thinner, etc. or items that may ignite.
*Do not install to the headlight with the light on.Failure to do so may result in malfunction or burns.
*This product is waterproof for daily life, but it is not completely waterproof.Wrap the coupler coming out of the controller unit with vinyl tape or self-bonding tape, or use caulking agent to waterproof it.Avoid wetting the product with more water than necessary.
*When washing a vehicle with a high pressure washer, please do not let the high pressure wash directly hit this product.
*Please do not drop the LED bulb or controller unit, or give it a strong shock.It not only causes breakage, deterioration of performance and shortening of service life, but also causes injury.
*When assembling the LED bulb, be sure to apply the supplied silicon grease to the areas indicated by the grease marks in the instruction manual.
*Do not cover up the waterproof fan.Make sure that there is enough space behind the fan for the sucked air to flow.
*Use a thread locker to prevent loosening of the threaded part.Periodic retightening is also recommended.
*Installation requires expertise and skill.Please have it done at a designated maintenance facility with skilled mechanics.
*Please adjust the optical axis before use.It may obstruct the view of oncoming vehicles and cause traffic accidents.
*PROTEC is not responsible for any damage or accident caused by the use of this product.Protec will not be responsible for any labor charges or other costs incurred during repair.
*If you feel any abnormality during installation or use, please contact your dealer or PROTEC service department.
Applicable Models
Super Cub 110 Pro 18-21
