- Home
- Model
- HARLEY-DAVIDSON 751 - 1000cc
- XL883R SPORTSTER
- Motorcycle Parts
- Bodyworks
- Chain Cover
- IKKOKU CYCLE WORKS
- IKKOKU CYCLE WORKS: Checkered Belt Guard
Checkered Belt Guard
- Product number: W-1405-P30132331
-
- IN STOCK
- Out Stock
- IKKOKU CYCLE WORKS
- |
- 0.0
- (0 review)
Check my coupons
Product Detail
Specification:
[Size] 95mm
[Description]
It's cooler without unnecessary stuff!
Racers are not equipped with anything other than what they need to go fast.
The lean and functional parts are beautiful, and the slimming beauty as a motorcycle can be seen.
The customization of Harley is different, if it has dress-up parts, it is cool.
Unilaterally, the belt guard (upper side) was identified as unnecessary, and the minimum size and the necessity for pillion users were considered.
The lower belt guard must not be removed as it is functionally necessary.
As you know, belt drive is maintenance free compared to chain drive.
There is no need to refuel or adjust the tension.
However, it is necessary to avoid accidental insertion of foreign objects such as small stones.
The lower guard is on the roll-in side and cannot be removed to extend the life of the belt.
Since the upper belt guard is in the direction of escape from the direction of rotation, the checkered belt guard is designed to be functionally unnecessary.
Material: Aluminum Checkered Plate.
The stopper collar is eccentric to prevent the collar from falling off and to allow fine adjustment of the mounting angle for various swingarm angles.
Duracon® material is used to prevent scratches on the swingarm.
The mounting part is made of aluminum collar and the eccentric part is made of Duracon® material.
Smart design with SUS ultra-low head bolts.
The mounting angle can be fine-tuned by using the excene-collar.
Racers are not equipped with anything other than what they need to go fast.
The lean and functional parts are beautiful, and the slimming beauty as a motorcycle can be seen.
The customization of Harley is different, if it has dress-up parts, it is cool.
Unilaterally, the belt guard (upper side) was identified as unnecessary, and the minimum size and the necessity for pillion users were considered.
The lower belt guard must not be removed as it is functionally necessary.
As you know, belt drive is maintenance free compared to chain drive.
There is no need to refuel or adjust the tension.
However, it is necessary to avoid accidental insertion of foreign objects such as small stones.
The lower guard is on the roll-in side and cannot be removed to extend the life of the belt.
Since the upper belt guard is in the direction of escape from the direction of rotation, the checkered belt guard is designed to be functionally unnecessary.
Material: Aluminum Checkered Plate.
The stopper collar is eccentric to prevent the collar from falling off and to allow fine adjustment of the mounting angle for various swingarm angles.
Duracon® material is used to prevent scratches on the swingarm.
The mounting part is made of aluminum collar and the eccentric part is made of Duracon® material.
Smart design with SUS ultra-low head bolts.
The mounting angle can be fine-tuned by using the excene-collar.
Note
* The image is only for reference. The image shown may differ from the actual product.
Caution
*DURACON® is a registered trademark of Polyplastics Corporation in Japan and other countries.
*Images include other sizes and models (installation images).
*When ordering, be sure to check the model and year of your vehicle and the rear suspension you have installed.
*If the length of the rear suspension or the number of teeth of the front and rear pulleys (sprockets) has been changed, the clearance between the belt and the belt guard will change and may interfere with the belt.
*Be sure to use a thread locker to prevent loosening when installing.
*There may be changes in product specifications due to the manufacturer's reasons.
*Images include other sizes and models (installation images).
*When ordering, be sure to check the model and year of your vehicle and the rear suspension you have installed.
*If the length of the rear suspension or the number of teeth of the front and rear pulleys (sprockets) has been changed, the clearance between the belt and the belt guard will change and may interfere with the belt.
*Be sure to use a thread locker to prevent loosening when installing.
*There may be changes in product specifications due to the manufacturer's reasons.
ALSO VIEWED PRODUCTS
Apply Coupon
Image Review
Review detail
/