Check my coupons
Quantity
100% Original
7 Days Warranty
Free Cashback
Net Price
Applicable Models
See All
XL 16-17 Narrow Glide Fork ABS/for 19,21
Product Detail
Specification:
[Size]
Handlebar cutting angle:43 degrees (One Side21.5 degrees)
Length from the bottom of the Under stem to the shaft:Stock460mm,2-inchesOver510mm
Wheel mounting width:Approximately 212mm
[Material]
・ForkBody
Topti
・Riser
・Caliper support
・Torque rod:Steel
・Caliper:Aluminum
Capacity
・Body
Topti
・Riser
・Brake Kit
・Shaft
・Wheel CollarXQuantity:1 Set
Handlebar cutting angle:43 degrees (One Side21.5 degrees)
Length from the bottom of the Under stem to the shaft:Stock460mm,2-inchesOver510mm
Wheel mounting width:Approximately 212mm
[Material]
・ForkBody
Topti
・Riser
・Caliper support
・Torque rod:Steel
・Caliper:Aluminum
Capacity
・Body
Topti
・Riser
・Brake Kit
・Shaft
・Wheel CollarXQuantity:1 Set
[Description]
Rubber mount XL1200C SPORTSTER 1200 compatible GLEAMING WORKSOriginal74 Springer Fork Kit
Redesigned for XLMODEL, where Bolt On installation was not possible with the previous InlineSpringer.
The handlebar angle is also kept to the maximum large limit, creating a nostalgic atmosphere..
No need to excise Handlebar Lock
To install normal 74 Springer on XL1200C SPORTSTER 1200 after 2004', the problem of interference with Handlebar Lock and Frame is large, high cost due to large width machining, almost impossible to get the handlebar cutting angle, etc.. There was a problem with the.
By reviewing the position of the Stem shaft, this product can be used as a Bolt On without any modification..
Handlebar LockOK, practical cutting angle, and the special brake kit provide the proper brake capacity, and the cost is also realistic..
Handlebar cutting angle:43 degrees (One Side 21.5 degrees)
Special casting design including top tee
The top tee (Top Bridge) is also exclusively cast and designed with a special riser to accommodate a wide range of styles from a compact handlebar to a classical style..
Redesigned for XLMODEL, where Bolt On installation was not possible with the previous InlineSpringer.
The handlebar angle is also kept to the maximum large limit, creating a nostalgic atmosphere..
No need to excise Handlebar Lock
To install normal 74 Springer on XL1200C SPORTSTER 1200 after 2004', the problem of interference with Handlebar Lock and Frame is large, high cost due to large width machining, almost impossible to get the handlebar cutting angle, etc.. There was a problem with the.
By reviewing the position of the Stem shaft, this product can be used as a Bolt On without any modification..
Handlebar LockOK, practical cutting angle, and the special brake kit provide the proper brake capacity, and the cost is also realistic..
Handlebar cutting angle:43 degrees (One Side 21.5 degrees)
Special casting design including top tee
The top tee (Top Bridge) is also exclusively cast and designed with a special riser to accommodate a wide range of styles from a compact handlebar to a classical style..
Caution
[Please be sure to check].
*Please be sure to read and understand the following information before purchasing this product.
■A note on brakes
*Springer forks are much less powerful than telescopic forks, which are almost exclusively used today. The special kit uses a weaker caliper than the standard one, as the rear arm will be heavily burdened if a strong braking force is applied. In addition, please drive by braking operation of the front 30%, the rear 70% approximately unlike standard sports stars.
*This product is a front fork of 80 years old structure. The roads and traffic conditions are very different from those of those days. The operating feel is also very different, so please drive safely until you get used to the operation (and of course after that).
■Attention in the ABS model
*Due to the mechanism of the springer fork, when the fork extends, the ABS sensor moves together with the wheel and rocker arm, so the sensor judges that the front wheel has locked up and the ABS is momentarily activated, causing the brake lever to move back. This may occur when the driver goes over a large step (such as the entrance of a convenience store) while applying the brake.
*Since this problem did not occur in normal driving tests, and Springer recommends the use of the rear brake, GLEAMING WORKS has decided to use it as a specification. However, if you are at all concerned, please do not install the springer.
*ABS operates normally when the front locks.
•It is about mounting
*Please make sure to ask special shop for mounting of this product.
*Those who do work should read carefully the assembly instructions and perform the work.
*Failure to apply grease, screw locks, etc. may cause serious accidents. GLEAMING WORKS does not guarantee any problems caused by failure to follow the precautions.
■About Neck Bearing
*When installing the springer fork, the neck bearing must be attached to the springer fork body. Depending on the year, the bearing may not come off from the under stem cleanly. In this case, please use the stock or stock-compatible bearings separately.
■Wear and tear of bearings
*Springer forks are much heavier than normal telescopic forks, and the stem bearings will be damaged faster because of the smaller fork stroke and lack of damping. Replace the stem bearings earlier than the manual says, and grease them frequently.
About Compatible Gasoline Tanks
*The stock tank of XL1200X other than the stock peanut tank (XL883N, etc.) cannot be installed as it is because the attached riser interferes with the tank. Please replace the tank with a new one.
*This kit does not include ABS Separator
*There are cases that it contains other product in the photo.
*Please note that the product specification may change due to manufacturer reasons.
*Please be sure to read and understand the following information before purchasing this product.
■A note on brakes
*Springer forks are much less powerful than telescopic forks, which are almost exclusively used today. The special kit uses a weaker caliper than the standard one, as the rear arm will be heavily burdened if a strong braking force is applied. In addition, please drive by braking operation of the front 30%, the rear 70% approximately unlike standard sports stars.
*This product is a front fork of 80 years old structure. The roads and traffic conditions are very different from those of those days. The operating feel is also very different, so please drive safely until you get used to the operation (and of course after that).
■Attention in the ABS model
*Due to the mechanism of the springer fork, when the fork extends, the ABS sensor moves together with the wheel and rocker arm, so the sensor judges that the front wheel has locked up and the ABS is momentarily activated, causing the brake lever to move back. This may occur when the driver goes over a large step (such as the entrance of a convenience store) while applying the brake.
*Since this problem did not occur in normal driving tests, and Springer recommends the use of the rear brake, GLEAMING WORKS has decided to use it as a specification. However, if you are at all concerned, please do not install the springer.
*ABS operates normally when the front locks.
•It is about mounting
*Please make sure to ask special shop for mounting of this product.
*Those who do work should read carefully the assembly instructions and perform the work.
*Failure to apply grease, screw locks, etc. may cause serious accidents. GLEAMING WORKS does not guarantee any problems caused by failure to follow the precautions.
■About Neck Bearing
*When installing the springer fork, the neck bearing must be attached to the springer fork body. Depending on the year, the bearing may not come off from the under stem cleanly. In this case, please use the stock or stock-compatible bearings separately.
■Wear and tear of bearings
*Springer forks are much heavier than normal telescopic forks, and the stem bearings will be damaged faster because of the smaller fork stroke and lack of damping. Replace the stem bearings earlier than the manual says, and grease them frequently.
About Compatible Gasoline Tanks
*The stock tank of XL1200X other than the stock peanut tank (XL883N, etc.) cannot be installed as it is because the attached riser interferes with the tank. Please replace the tank with a new one.
*This kit does not include ABS Separator
*There are cases that it contains other product in the photo.
*Please note that the product specification may change due to manufacturer reasons.
Applicable Models
XL 16-17 Narrow Glide Fork ABS/for 19,21
