Reviews
Puch SIDEDownForceSpoiler
In conclusion, it is absolutely impossible to install it properly.
If the pattern paper is Quantity:I also had trouble with only 1pc.
And the pattern paper is not Exactly to match the top?
The location will change by about 5 cm depending on whether you want to adjust it to the bottom or the front or the back
The procedure is different if you refer to the Webike Product Page video for installation
In the video, Plate is applied first, and after 24 hours, Rubber rubber is placed over it.
Product was sent already installed!
This is because the Plate is located behind the Rubber Rubber.
Rubber rubber like Toilet's SUPPON will rebound like Spring and interfere with installation.
I looked it up on the Net and found that those with strong final strength have weak initial strength.
We are a GarageHouse, so our cars and motorcycles are both heated and cooled in the house!
Compress and paste for 1 minute at room temperature above 28 degrees Celsius or
I tried and tried, but it was impossible.
Emon sold separately (amon) Ultra Strong Double-Sided Tape (for Bumper, Spoiler, etc.)
Buy Strong Fixing Type White 25mm×width 2m×length 1.14mm×thickness 1.14mm 3910 for outside of car and
I machined and installed it.
The product is quite straight and is to be mounted on a curved cowl.
It's not so much that it's attached as it is that it's forced to be attached with Strong Double-sided Tape!
The shape does not fit the side cowl of the ZX-10RR at all.
I'm inclined to say that it's a 2021ZX-10R/ZX-10RR exclusive part.
ZX-10RR looks straight but Cowl is quite curved
It doesn't fit at all, especially the Right Side is almost floating.
If this is what you're talking about installing, I'm pretty sure it applies to all other Manufacturer's Motorcycle's.
Whether it is YZF-R1M or CBR1000RR-R, it is possible to paste it!
At the moment, I've driven about 50km to try it out and it hasn't been removed.
It looks cool, so that's good.
View detail
Fits: KAWASAKI GTR1400, KAWASAKI NINJA 250R, KAWASAKI NINJA 300, KAWASAKI NINJA H2 SX, KAWASAKI VERSYS X-300, KAWASAKI Z300, KAWASAKI ZX-6R 636, KAWASAKI ZX-6R 636, KAWASAKI ZX-10R, KAWASAKI ZX-10RR, KAWASAKI ZZR1200, KAWASAKI ZZR1400
Do I need a Screw lock?
Installation is not particularly difficult, Material:I have been using it after cleaning the bolt, but I recommend that you buy a commercially available bolt and replace it when it becomes doubtful. I have been cleaning the bolt and using it, but considering the durability when I repeatedly loosen and tighten the bolt every time I change the oil, I recommend purchasing a commercially available bolt and replacing it when it starts to look suspicious. The color, processing, and finish are very beautiful and I like them. View detail
Mugen VFR800X Long Screen
It would be nice if the delivery time could be a little faster.
The quality of the product itself is good.
The wind regulating effect is better than OEMScreen.
View detail
Cell Phone Protection
I bought the Short one so it only provides some wind protection.
Main is a cell phone blindfold & rainproof attached to Handlebar!
Main is doing its job well.
Variable Type is good but a little more Cowl? to
I think Motorcycle will look much better if it gets closer.
View detail
overhang
[How is it used?
Circuit 70% Touring 30%.
Was the one you received as per Image?
Design and texture are as shown in the Image, but the adhesive part is sticking out.
Do I have to cut this myself? I don't know how to use it.
Was the installation difficult?
Should I install it? I'm having a hard time.
How was your experience with it?
before use
[Included Parts:were they on?
Sticker and degreasing? Included Parts:, Instruction Manual
[Was there anything that disappointed you?
As I mentioned above, what should I do with the overhang of the adhesive side?
I don't know. I didn't install it.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
Instruction Manuals in many languages are included.
It doesn't say anything about the overhang.
I'm worried about it.
View detail
Unique shape
I've been looking for a comfortable Screen in Position when Touring and this is the third one and it finally feels right.
If you get down, it's almost windless, but with Dark smoke, nighttime visibility is hard to see. [Color] Maybe I should have left it at Smoke.
In a slouched position when touring, airflow is generated from the middle of the helmet's shield to the top of the shoulders.
The Wind Cutting noise that occurred with the previous WRS Screen is much better.
Design-wise, both SIDEs seem to be slithering without sleeping, so I thought people might be concerned….
View detail
It's both Practical and Design!
Without the Rear Fender, even the bottom of my pants would be wet. After installation, the effect and styling are perfect! View detail
Not too Black and not too thin
This is my first time using a pouch and I am very happy with the shape, color, and cosmetics. I recommend it. This is just my personal opinion. (Lol) View detail
The construction is simple and requires some ingenuity.
I chose this one because I prefer SIDE with Stages.
Installation Nut is an OEMParts 90179-05523. It is not included in the
You can use the OEM's Screen, or you can use the one that comes with the OEM's Screen.
I bought 4 of them at the same time because I wanted to deform and fix the Rubber.
The OEM has claws for hooking near the Mirror and Meter.
To remove it, Mirror must also be removed.
In contrast, this product does not have such a feature, making installation very easy.
On the other hand, since the fixation is not done at the front but only at the rear nut
The front of the Idling also makes a rattling sound when it is shaken by the vibration of the Engine.
As a countermeasure, we use harness tape, which is similar to cloth and leaves little adhesive residue.
The sound has subsided when I have spread it around the perimeter while adjusting it with Scissors.
Vinitae or something like that would be fine, but I think the Harness type would be better because the glue seems to melt at high temperatures.
Overall, it is good, but it would have been better if there had been claws on the front side to hold it in place.
View detail
Fits: BMW R1200GS, BMW R1200GS ADV, BMW R1200GS RAL, BMW R1200GS EXC, BMW R1250GS, BMW R1250GS ADV, BMW R1250GS HP
Just right.
I installed the Smoked color ones, and the visibility through the Screen was at a Level that was fine even at night.
The windshield works well, but I'm 172cm tall, and when I raise the screen to the top, I have to look forward through the screen, so it may be different for different tastes. (The body is R1200GSPremium line with Normal seat)
Installation is easy, even for beginners.
View detail
Easy to install
It is inconspicuous but seems to protect against mud stains. View detail
FISCO at full throttle but at full throttle.
I have been riding BRUTALE and understand wholeheartedly that it is HIGH PERFORMANCE, but there is a problem.
It is to be NAKED.
At full throttle, a considerable speed can be obtained, but since there is no cowl, the wind pressure on the rider will be at a very high level.
Of course, if a Screen was attached, it would have prevented this to some extent, but I never attached it because of the design issue.
The Puch Screen installed this time is the best match to the BRUTALE1000RR's design.
The performance has been Checked by FISCO.
Even with the FISCO Straight at full throttle and about 280 km/h, the wind pressure was at a Level that did not bother me at all.
Breaking from full throttle also did not cause any anxiety in operation.
I would highly recommend it to BRUTALE riders.
View detail
MCS 19:21 as for Replacement
[How is it used?
I used to run Circuit by replacing it with ZETA Flight lever.
In terms of protection for the master cylinder, the Retractable Lever should be used, but the adjustable lever ratio of the MCS 19:21 is difficult to discard, and I have returned to the OEM lever in the past, knowing the risks involved.
This product can be made Foldable while retaining the Lever ratio adjustment function by porting the OEMLever Unit.
A product with similar functionality is available from KTMPowerParts for the 890dukeR, but we chose this one because it is very expensive and there are no repair parts available.
If you are planning to buy STREET TRIPLERS and are thinking of running Circuit in the future, you may want to order them as soon as possible.
Was the one you received as per Image?
Yes
Was the installation difficult?
Manual was easy to understand and simple.
However, when removing the MCS19:21 unit from the OEMLever, a 1.5 Hexagonal Wrench was needed, so we bought an additional 1.5 Hexagonal Wrench.
How was your experience with it?
The shape combined with the lever side is not so different from that of the OEM lever and can be used without any discomfort.
[Included Parts:were they on?
Yes
[Was there anything that disappointed you?
The product itself is fine, but the delivery time is long due to the small number of car models supported.
View detail
MCS 19:21 as for Replacement
[How is it used?
20552N (Brake leverAdapter for MCS19:21) It is used in combination with
Combined with the above Adapter, we were able to make Lever Foldable while keeping the Lever ratio adjustment function alive.
Was the one you received as per Image?
Yes
Was the installation difficult?
Manual is easy to understand and simple, but some design errors (Another component selection error?) It should be noted that there are some areas that seem to be
How was your experience with it?
The shape is almost the same as that of the OEMLever and I can use it without any discomfort.
[Included Parts:were they on?
Yes
[Was there anything that disappointed you?
The Clearance of the Nylon nut at the connection with the Adapter and the seat grip is small, and it cannot be tightened to the end as it is.
Since the supplied Nylon nut is a low head type, I solved the problem by purchasing a Standard Type Nylon nut at Home centeretc.
View detail
Fits: BMW S1000 R, BMW S1000 RR, HONDA CB1000R, HONDA CBR600RR, HONDA CBR1000RR FIRE BLADE, HONDA CBR1000RR FIREBLADE, HONDA CBR1000RR FIREBLADE SP, HONDA CBR1000RR FIREBLADE SP2, HONDA CBR1000RR FIREBLADE, HONDA CBR1000RR FIREBLADE SP, KAWASAKI NINJA H2 SX, KAWASAKI NINJA 1000SX, KAWASAKI VERSYS 1000, KAWASAKI Z900RS, KAWASAKI Z900RS CAFE, KAWASAKI Z1000, KAWASAKI Z1000SX, KAWASAKI ZX-6R, KAWASAKI ZX-6R, KAWASAKI ZX636
very good
When I bought Puch's Engine Cover in the past, I was treated to the foreign quality of Puch's LogoSeal being applied on the opposite side, but this product is as good as I imagined Parenthesis to be.
The city is full of PremiumZones, so it is very good for those who want to do a different Custom, and honestly, this one is Parenthesis (personal opinion).
View detail
HYPER Overseas Quality
Screen was a pooch, so I bought it to match, but oooh, oooh, oooh, oooh, oooh, oooh, Logo is backwards, this guy.
I couldn't believe my eyes and thought I had been given a crackpot, but it was a legitimate product.
The Logo was Double-sided Tape, so I removed and installed it and it was cured.
The texture is honestly better than GB's, but I would recommend it to anyone who wants to have it in a pooch, and it's also about 10000 cheaper.
View detail
Safe parking for Camping area and hot Asphalt.
I was concerned about the small side stand with a small ground surface, so I purchased this product, which is compatible with the TORACER.
The design is good and anyone with a Hexagonal Wrench can put it on.
When I temporarily aligned the upper plate, it floated a little, so I was a little concerned, but after tightening the bolt, I was able to attach it without any problem. Just to be sure, I tightened the bolt after applying screw lock agent.
It is safe even if you forget the STANDPad during camping touring, and it eliminates the fear of tipping over when parking on the hot Asphalt in the summer.
I guess it is a little expensive for a car model-specific product of Puch, but I gave it 3 stars for cosmetics.
View detail
The first LightCustom you can do
About 3 cm above OEMScreen? It seems to extend upwards.
Wind flow can be felt when driving on the highway.
I'm 169 and the wind blowing from the neck down is obviously reduced, but I feel that the Helmet is often hit by the wind and the Wind Cutting sound is increased.
It's helpful in cold weather.
The design is a different shape from the OEM, but this is cool.
See photo for transparency of Dark smoke. even though it is DARK, you can see the other side.
Installation was also super easy.
View detail
Contributes to stabilization of Long Screen
When we introduced the company's Long Screen, we could not deny that the longer screen was unstable. After installing this product, it became stable. It is not conspicuous when viewed from the side, and it is calm and solidly supports the screen in an OEM-like manner. This product itself is quite heavy, and when moving the screen, the dial becomes hard, so a little hang is required. The price is a little high, and it would be better if the price were a little lower. View detail
Fits: MOTOGUZZI V7 850 SPECIAL, MOTOGUZZI V7 STONE 850
I want to reduce mud splatter.
I didn't want to get the Dynamo cover on my Dynamo cover even if it passed a little bit of moisture, so when I discovered this product... Yes!" I thought
The installation is specified to use both double-sided tape and Rivet, but I don't like Rivet that requires drilling holes, so I stuck the supplied double-sided tape all over the joint and am looking at how it is doing. It is still running about 1000 km and most of the driving is high pace winding driving, but so far it is completely Large and strong. I am concerned about the adhesive strength of the tape under high temperatures in the summer, so I will be careful in the future and keep an eye on it.
My personal ideal is to wear it for function rather than appearance, so I wish it were a little longer (3~5?).
these days I wonder what the turnaround time is." I was glad that it was sooner than I had been notified.
View detail