High quality, above price

Was the one you received as per Image?
As per Image.
The packaging is boxed and the box looks expensive.
Quality is already high.

Was the installation difficult?
The handlebar is assembled to a certain degree from the beginning, and only the Handlebar End and Mirror need to be removed.
Can be installed.

How was your experience with it?
I don't know how effective it is yet. I mean, I don't want the day to come when I do.
It is more for windproofing purposes.
I think it works because I don't get bugs on my Gloves anymore.
Above all, the quality of the products is very high.
The packaging is also tight.
Sticker is also Accent and very good.
Note that GripAccess from the Bar End will not be possible.
Nothing wrong with everyday use.


[Included Parts:were they on?
Sticker

[Was there anything that disappointed you?
nothing special
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer

Sticker reserve should also be available for purchase. View detail

Inexpensive for a Puig?

[How is it used?
Machined and installed on OEMFender

Was the one you received as per Image?
As per Image.

Was the installation difficult?
First, it is essential to remove the OEM Fender.
It is not that difficult to take it off, so if you have a tool, it is Large sturdy.
However, the screws are hard because each screw has a loosening stop.
Be careful not to damage the rear brake line.
Apply a Large amount of strong Double-sided Tape to OEMFender.
Double-sided tapes of various shapes were included, which looked sickening.
But each one is quite powerful.
Then, with the pieces attached, drill four holes with Drill.
After penetrating, use the supplied Material:Strike Plastic's Rivet and you're done.

How was your experience with it?
Quality is quite high.
Designed to fit OEMs perfectly.
It does not seem to have become more effective as a mudguard....
I just like the look and feel of the OEM chic.
It is very rigid and does not feel like it can be taken off at all.

[Included Parts:were they on?
Double-sided tape for mounting, Rivet

[Was there anything that disappointed you?
The Puig Sticker shown in the product photo was not included.

Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
Please include Puig's Sticker in the product photo. View detail

Large Satisfied

I am satisfied with the appearance Large.
I wanted to put Sticker on it, so it was the right choice to go with Dark smoke, which I don't mind from the driver's seat. View detail

Straight and windproof effectLarge

Although we try our best to stay down at Straight, we are huge and the wind has a large effect on us, so we purchased this product.
We had thought Kawasaki was a pooch as our own Image.
It was very easy.
The installation is Kang Tan.
However, the word ninja is not necessary. View detail

Screen replacement for ApriliaRS660

Replaced from OEM Screen.
We chose to install the Puch Racing Screen, which is a high screen, because of the wind impact on our bodies and helmets on the highway.
The effect of wind exposure has been reduced compared to before, making driving more comfortable.
[Color] Since it is Smoke, I am satisfied with the Parenthesis because it is ExactlyMatched to Motorcycle. View detail

It's effective. [Color] Smoke for a Sharp Look

To be honest, I don't race, but I can't avoid the wind pressure by putting my head inside the normal screen unless I look straight down. You can't see the front. How much difference does a mere 3? I'm 171?68?and almost standard size, but it surely had an effect on me. I feel its benefit when accelerating in a straight line at full acceleration and when cornering at high speed in a prone position.
Well, more than efficacy. [Color] The main reason is that I wanted to make Smoke look sharper. A little thinner. [Color] It was Smoke...would DARK have been better?
There is also a double bubble, but I decided on a pooch because I thought a simple, small look would be suitable for Panigale.
Edge portion is left uncut (same thickness) The lens is not easy to deform and there is no distortion of the field of view. For the price, I am generally satisfied. I'm going to use Clean Inno Beta by Viroz, which I also use for helmet shield, to maintain it. View detail

Not as effective as a windshield.

I installed it because it was NAKED and had no windshield at all.The texture is nice, although I didn't like the design a bit. The effect as a windshield is not so great on ordinary roads, but it is effective at high speeds. I think the effect is especially large on the 120 km section of the New Tomei Expressway. View detail

Looks especially cool from the side.

Installed on a ZX14R.

In the picture on the product page, it looks like it has a bad parenthesis, but in reality, it has a very good parenthesis shape.
My personal favorite is the GizaGiza shape, especially when viewed from the side!

Accurate and easy to install with no modifications! View detail

MF15 Touring screenV-TECH TOURING installation

This time, we installed Puch's Screen in Dark smoke to match MF15's Black.
Installation is so easy that no special instructions are needed.
Also, I think it looks even cooler now that it is all in black. View detail

The effect is too Outclassing!

When I bought a used VERSYSX250, the previous owner of the Puig [Color] The OEM + 115mm UIndia Protection effect is outclassing and allows the Helmet Shield to be semi-open when driving on high speed roads. It also has a transparent [Color] Since it is a clear type, raindrops can be avoided by the screen when it rains, and combined with the aerodynamic style of VERSYS, the body can hardly get wet except for both shoulders. However, if it is this large, the air resistance is also large at the maximum speed of 120km/h section of the Tohoku highway, and in a strong headwind, the maximum speed is affected and the Meter reading is only 119km/h. In addition, there is considerable damage to the fuel consumption, which is less than 20km/L. Therefore, if the speed is less than 100km/h at high speed, the fuel consumption will not be affected so much, and if it is a general road, I think the high UIndia Protection will reduce the burden of long distance touring. And even at high speeds near the limit, there is no vibration and no effect from crosswinds, so I think it is a well-made touring screen that is more than the price without flattery. View detail

I purchased this product to install a Fog Lamp.

I installed it on a 2020 vstrom 650.
Even with Under Cowl, you can still manage to install it.

I'm happy to see that the Fog Lamp I wanted has been installed! View detail

It's not accurate.

I was attracted by the look of the product.
Frankly speaking, I wish I had not bought it.
It is not worth $27,000.

First of all, BALI is amazing.
My bad for being careless, but the Edge part. Hmm?" Is this BALI…?" So I traced it with my finger and it cut my finger.

In the meantime, the entire BALI removal is a must.

Also, it is a combination of Bracket of Gold genus and Spoiler of ABS resin, and it is hand-finished and processed by puig, and it is Quantity.:Pair (for Left and Right) The shape was different in

When I put it on for the time being, the Right Side hits the DummyDuct as hard as it can. When I cut the Handlebar by force, the Right Side was so hard that it was cutting into the Spoiler and made a cracking sound.

I had no choice but to cut off the area hit by the luther as much as I could, referring to the Left Side, which was not hit.

"If you shave off that much, you can't hit a rock…"
But this time, the Bracket itself of the genus Gold was hit.

There is room on the Left Side but not on the Right Side.
Is there something wrong with the way it is attached? I tried to adjust it by loosening the screw, but it only attaches where it should and it only shifts a few millimeters, so I was out of luck…

Could it be that the DummyDuct of the MT09 itself has become dislodged? I thought it might be a problem, but it wasn't. ….

To be honest, is this a defective product? I think, "I'm going to have to give up and be patient and use it," but since I've shaved it off. View detail

It looks different and performs better!

The OEMShield is also reasonably windproof, but if you're tall like me, I think it's a bit more. Now that I've switched to this one, I feel it performs, and I like the way it looks again!

However, I wonder if the price is too high… View detail

Puch Racing Screen Z-Racing

As Image
It's like the motorcycle in the United States' Black people music video.
Looks great on the 2021Ninja ZX-10RR! View detail

rear flip

Fuic rear fan fast delivery and good quality cbr1000rr-r is just right I recommend View detail

Parenthesis is good & windproof.

OEM is not bad, but Parenthesis is good! Made in Italy!
The same level of windproofing effect as when the OEMscreen is attached at the top.

I have no particular complaints.
When I installed it, I was a bit nervous because I thought the holes were not aligned properly, but if I deflected the Screen a bit, it came on fine.

Pooch's Screen, not just this one, but all of them, are both Design and windproof, brilliant! View detail

This is for wind protection.

Purchased to add wind protection.
Great product.
It was a big difference between having it and not having it.
It's like the wind that was coming over my whole body is now coming around my helmet.
At the same time, I made it a Swallow handle.
It leans forward and provides additional wind protection. View detail

I am satisfied with its performance and appearance.

It sticks out above the OEMScreen, so that it is barely exposed to the wind when it is down.
If you are driving on a circuit, you will be able to feel the effect.
In contrast to the simple shape of the OEMScreen, the 3D shape of the screen is more rigid and less prone to deflection when pressed.
Installation is simple, just swap the bolt between the Hex and Bolt and snap it on. View detail

Jack-up is required

I bought a genuine product, although there are Chinese products on Amazon and other sites for half the price. It is a solid product, and although I did not compare it to the Chinese product, there is probably a difference in material, rigidity, and surface treatment.

The Washer and other parts listed in the Instruction Manual were not included. I had them on hand, so it wasn't a problem, but for a product of this price, not being able to find the parts listed in the Instruction Manual is a bit of a problem. I've deducted one star regardless of how complete it looks.

The instruction manual says it's easy to just pull the bolt out and install it, but in reality you have to jack-up the pivot part of the Swing Arm. If you don't do this, the thickest bolt will not come out, and even if it does, you won't be able to put it back in. View detail

It has a futuristic feel!

The MT09's futuristic-looking mask looks even tighter.
Combined with the Light part, it makes for a cool X-shaped forme!

It's not a performance enhancing part, so it's totally custom looking, but it's a great design that shows off Puch's sense of style.
If you're not sure whether to wear it or not, this is a part you won't regret. This is a part that you will not regret wearing. View detail