Thermal measures!

I installed an Oil Temperature Meter on my NC750X, but I have to pass the WiringCable under the Engine, so I will try this heat resistant tape as a thermal countermeasure. I think it will be no problem. I am also planning to put the heat resistant tape on the Under Cowl of the NC750X because the heat from the exhaust system melts the Under Cowl. View detail

Highly universal design like a certain manufacturer's OEMBolt

[How is it used?
I purchased the DRC Aluminum Spacer for M6 to go along with the SEROW225WE as a Bolt to match when used to secure the exterior of the SEROW225WE.
The following items are "DRCAluminum spacer and Quantity:The "State used in Set" will be in Review.
Was the one you received as per Image?
As the title suggests, it is a bolt with a Flange that can be turned with an 8mm size Socket or Wrench, I believe that this Flange makes the Large size fit the recess of the Aluminum spacer perfectly, which leads to the sense of unity when the exterior is fixed.
The product was as per the Image.
Was the installation difficult?
The method of use is no different from that of a regular bolt.
How was your experience with it?
I tried to match several different Bolts in combination with Spacer's Spacer made by DRC. Design without being too assertive." Several lengths are relatively easy to come by." Cost per unit performance." I have been using this Bolt in my Spacer vehicle since then.
[Included Parts:were they on?
There are no Included Parts:other than Bolt.
Quantity of 2 Bolts in a Package made of Vinyl:The product is sold in each length as a Set.
[Was there anything that disappointed you?
It is Uniqlo plating, so Rust may occur in some environments, but considering the mature design and cost performance, it is a sufficient product and I have no complaints.
Other items that would be helpful
Point and hang of installation
The aluminum spacer is changed to match the coloring of the location where the bolt is used, and the bolt length is the same as that of the OEMBolt.
[Notes]
Since the head part is 8mm in size, if the proper tool is not used, the corner will be licked and it will not be able to be tightened at the specified torque, and rust will easily occur.
Any Bolt should be carefully tightened or loosened using the proper Size tool.
[ITEMS TO BUY TOGETHER
Naturally, it can also be used with Single Body.
However, I think it will look even better when combined with an aluminum collar, as I did this time.
[Opinions and requests to Manufacturer
Thank you for the lineup of various lengths.:I would appreciate it if you could sell Stainless Steel products. View detail

Required for Fender Eliminator

I installed it to reinforce the Plate since I used a Fender Eliminator.
I am glad that this PlateHolder comes with a reflective version, as the Active kit does not have a reflector! View detail

Black and hard.

Black and hard.

I know it's short.

It's not about length.

It's hardness, after all.

Black Dye Bolt is my favorite.

I think I'll buy the Black dye solution. View detail

Pretty good

Installed on Z900RSNormal swing arm.

This is a good choice for those who want to black out their feet while keeping the normal swing arm. (,,> <,,)

It's not a complete blackification since ASKULShaft and Hub bolt are Silver, but if you look closely Oh!" I am very satisfied with the quality of the food. View detail

For installation of Rear Sets

Apparently, a button cap bolt is good for the Rear Sets attachment point to prevent them from getting caught on the shoes, so I used this one.

It's not easy to find these sizes at home centers, so it's nice to be able to choose the size and type in detail at Pinpoint. View detail

Mirror Holder is no longer available.

[How is it used?
I bought a used WR250R before the price went up as much as it has now, and it had a ZETA Pivot Clutch Perch CP installed at first, but the Mirror was only installed on the Right Side, so I had to replace it with a ZETA Pivot Clutch Perch CP. Is it legal to use a LargeMirror without LeftMirror, or is it scary when changing lanes?" I looked closely around the clutch and found that the ZETA clutch holder does not have a screw hole for mounting Mirror!
The OEM clutch holder of the WR250R has an integrated Mirror Holder, so when it was replaced with a ZETA one, the Left Mirror could no longer be installed.
I ordered this product as soon as possible to avoid danger, as my driving skills and ability to perceive danger are not very good.
Did you receive the item as per the Image?
I ordered the product after thoroughly checking Webike's product description section, and it was exactly as I had imagined it to be.
Was it difficult to install?
BoltQuantity this product to the space in the root river of the Clutch holder attached to the Handlebar.:It is a simple job to attach with 2pcs.
Quantity:Pair (for Left and Right) If the Mirror mounting spacing of the two mirrors can be installed at the same location, there will be less discomfort when the Motorcycle is viewed from the front.
How did you like it?
Once firmly installed, the Mirror Holder is a normal Mirror Holder without any Mirror gaps while driving.
When I purchased it from Webike, it was on sale at Timing, so I was able to purchase it at a lower price than OEM holders for other vehicles.
Was "Included Parts:" attached?
BoltQuantity for HolderBody and mounting:2pcs are included in the package.
Were there any disappointments?
I purchased a Blue alumite product and it faded faster than other Anodized dyed products.
I am thinking of painting it matte black with a cheap can of Spray if the color fades any further.
Other items that would be helpful
Point and hang of installation
As I mentioned above, I think it would be less uncomfortable when viewed from the front in Symmetry if the Holder is mounted at the same spacing as the Mirror position on the Brake Side.
[Availability and clarity of the Instruction Manual
I don't think there was an Instruction Manual...sorry my memory is a bit hazy as I purchased it quite a while ago.
[Notes]
There is nothing special in terms of functionality, but Blue alumite fades quickly, so I think it would be safer to purchase Black.
[ITEMS TO BUY TOGETHER
This is an opportunity to use your favorite MirrorQuantity:Pair (for Left and Right) I wonder if it would be customary to purchase a "Custom"?
[Opinions and requests to Manufacturer
The color fades quickly, so I would like you to take measures to prevent this, and I would like you to continue selling this product for as long as possible. View detail

Used for reproduction of old cars with direct cord

[How is it used?
old car (SportsCUB) Used in Restore of

Was the installation difficult?
Both cords are not too difficult to screw in.
Remember to put the Heat Shrink Tube through beforehand.

How was your experience with it?
Once again, I thought it might be a little dangerous since the insulation is taken only by Heat Shrink Tube.
If the Tube is Gapped or frayed and breaks, high voltage is exposed.
Installation location should be noted.

[Included Parts:were they on?
Instruction Manual is provided, so you will not get lost even if it is your first time. View detail

It has a good VINTAGE atmosphere.

It looks good on SR400CafeCustom with VINTAGE atmosphere and high class feeling. I extended the wiring and installed it near the front of the engine on the Left Side of the body like a VINTAGE English car. View detail

Looking for something similar but can't find it?

It is rather expensive,
Plating of iron instead of Stainless Steel
Cap Nut in Flange without Serrete
Hexagonal section is long
I have not been able to find anything at tool dealers or other places that meets the requirements of the above.
I'm sure I can get them more inexpensively, but it's already too dull to look for them.

It is just right for use on the Exhaust stud bolt of the Exhaust System, where you want to avoid troublemakers and such when removing and installing.
There are no concerns about the quality of the plating, and no particular peeling or rusting appears even after long-term use. View detail

Replace while opening Engine

Quantity like this:When it comes to Sets, there are some things that are not necessary, but this Quantity:Set is just what I need, so that helps. View detail

Replace during overhaul of Monkey engine

I replaced it at the time of overhaul of the Monkey engine. Since it is a consumable part, I thought it would be safer to replace it at the engine opening timing, so I replaced it. View detail

Is it a necessity if you want to Race?

[How is it used?
It was installed on the front master cylinder of a YAMAHA TZr50R under restoration.
It appears to be installed as Protection for Master Cylinder in case of tipping over.

Was the one you received as per Image?
I have an XJR with a Tank Separated Type radipon, so I did not know that this kind of product existed.

Was the installation difficult?
It's easy to change the OEM countersunk screws to hexagonal and install.
Master Cylinder's plate screws are easy to lick, so I would be grateful for a change to hexagonal.

How was your experience with it?
The previous owner had been playing Race and had solid fall scratches.
However, the Master Cylinder side was not affected, so it seems to be fulfilling its role well.

[Included Parts:were they on?
Hexagonal Screw

[Was there anything that disappointed you?
I think there are too few color options.
Color Anodized Aluminum looks cheap, so it would be better to have a more Large person color! View detail

It stands out

It's just a Bolt, but it's beautiful and stands out. View detail

Total length 190-200

Excellent appearance and rustproofing performance.
I am using it on the APE100 at the same time as a Side Stand Bracket from another company, but it is too short and may cause the vehicle body to lean too much. View detail

Windproof and light-blocking properties are good.

Purchased to prevent wind from getting into my eyes as much as possible due to Dry Eye.
I like the light weight, good Fit, and light shielding; I don't have extreme visibility concerns when in the Tunnel.
The item arrived and the Left Arm came off immediately.
I reinserted it, but it did not seem to be inserted properly. Since then, it has not come off.
It was a product that I would like to repeat because it is cosmetically pleasing.
I gave it 4 stars because the Arm was not inserted properly. View detail

One point

I used it for One point around Handlebar. It is a completely self-sufficient part. View detail

wait-and-see

I bought it thinking it was a faulty OEM Relay, but I never used it due to poor contact with the wiring, but it is made by POSH, which is reliable and almost half the price of OEM parts. "No sound." If you don't mind the "I'll buy it", I think it's a good buy.
I wonder if OEMRelay is being UPDATED. (!) View detail

It looks very nice

As the product photo shown, the grip is very classic and comfortable. Its look is quite similer with Bitwell Kongfu grip. View detail

Ideal for crime prevention.

This is no longer an exquisite product.
The combination of anti-tinkering Torx bolt and anti-loosening Nut is kind.
The design is simple and the color line nap is abundant. View detail