Reviews
The one and only Tool that grinds Caliper pods
I'm not sure what else Tool can do for you.
It is the one and only Tool to grind Caliper pods and you may want to have one!
I've never used the other one, so I can't compare, but it gripped the pod well and was able to grind away!
Click here for the Bad replacement procedure.
https://imp.webike.net/article/636859/
View detail
Good cost performance, OEM same etc. Crimp structure is also safe.
Used to refresh a NORMAL rubber hose that had been used for nearly 40 years since new and had cracks on the surface.
The Crimp is made by NICHIRIN, the same company that makes the OEM Brake hose, and the connection to the banjo section is the same quality as the OEM Crimp.
We purchased this product because it is durable and reliable for long-term use, and it kills two birds with one stone:it also provides a Snap and BrakeTouch as a mesh hose.
Performance is fine.
After installation, the Crimp was not handling well for about a year, and it was pulling tight due to interference with the Cowl Bracket at full lock, but the Crimp did not pull out and the Hose did not break.
In order to reduce in cost and increase reliability, the panjo adapter is fixed and there are only two types of orientation, 90-degree right angle or parallel, for the upper and lower panjos, and only two types of banjo adapter angles, straight or 20 degrees, so you have to choose the type of car to install. The banjo adapter has only two angles, Straight or 20 degrees, so you have to choose the type of car you want to install it on.
View detail
useless
Purchased for Spoke maintenance. Conclusion:It can't be used. First of all, I can't use it with Harley because I can't get over the bumps. It was faster to use Jack. View detail
Fits: Others NISSINMaster cylinder tank cap O.D. 59 (some φ61)
For Dress-up
Used for Nisshin's 5/8 Radial master Tank.
It is just a replacement for the OEM plastic Cap, but it looks spectacular.
View detail
Front and Rear are also replaced with the same brand.
I felt a chill when touring with Tandem touring, so I replaced the Rear with this pad from DAYTONA along with the Front.
Satisfied with both braking power and control. No complaints.
View detail
To replace a deteriorated and obsolete Radiator hose
This is a combination of Straight Type hose and Hose Joint Pipe and is used as a substitute for the Radiator hose, which has been discontinued and cannot be replaced.
The coolant was nearly 40 years old and had deteriorated to the point of leaking, but we were able to stop the leak by replacing it.
Although it was not possible to make it the same shape as the NORMAL, both the inlet & outlet could be made in the same position as the NORMAL, and the substitute could be made without putting a load on the hose.
View detail
Combined with the company's Universal Radiator Hose, it is a savior for old car riders.
The pipe itself is not made of soft aluminum or brass, but a solid iron-like pipe. The pipe itself is not made of soft aluminum or brass, but of solid iron, so there is no deformation of the pipe due to tightening of the band, and it can be tightened firmly, so there is no leakage even if pressure is applied.
The ends of the pipe are also thickened to prevent the hose from falling out, so as long as the hose band is properly tightened, the hose will not fall out even if pressure is applied.
View detail
Limited installation methods for back camera
Wiring length of the back camera is halfway; 1m on the Camera side and 1m on the Extension Cord,
The Camera side should be about 30cm and the Extension Cord should be about 2m.
Unlike a driver's camera, the Body's mounting position is near the with handle, so the current wiring length requires a connector connection at the halfway point, making wiring difficult.
The Cable that connects to the Body also has a 4-point screw on the Body Reverse side, but this is troublesome to install.
With this structure, even if the BodyMount base can be removed with One-touch, when the Cable is inserted again,
Since the connector is fixed with a rubber band to prevent 4-point tightening, it is necessary to use a precision driver to remove the screws and insert the cable before fastening the screws, so the screws are left attached after all.
The four screws on this base are not designed to be detached, so if they are completely removed, the screws may be dropped and lost.
The back camera can only be mounted on the upper side of the base in the direction from which the camera is suspended, and cannot be flipped up and down in the body settings.
The position of the Fixing Screw between the Base and Camera is not in the Center, so changing the mounting direction of the CameraBody is necessary,
Difficult to set the adjustment angle downward because the angle of the Camera is Up.
I tried attaching it to the Fender, but it could only be adjusted slightly Up from horizontal.
View detail
Fits: KAWASAKI Ninja ZX-4R SE
M820WDController CT110 HUNTER CUB Brake folder Exactly for mounting
[How is it used?
MiVue M820WD Drareco Controller mounted in the Right SideBrake folder of the CT110 HUNTER CUB2BJ-JA55.
Although the name of the folder is Clutch folder, as shown in the product description photo, the folder can be attached to the Right Side Brake folder as well, effectively and securely.
Was the one you received as per Image?
Yes
Was the installation difficult?
It is easy. The angle of the brake lever changes when the brake folder fixing screw is loosened for installation. If you mark the current position before loosening the screw, you will not have to readjust it when assembling.
How was your experience with it?
It can be mounted securely, making it easy to work with Switch operation.
[Included Parts:were they on?
Yes. Matching mounting Bolt and collar are included and ready to install.
[Was there anything that disappointed you?
There is none. As expected.
▼ Requests
It would be easier to find a Brake folder if the name of the product listed is "Clutch holder...".
View detail
Hazard.
It is easy to install., No problem, good product! View detail
If you don't need O-rings, click here.
I often buy DAYTONA's Perfect set, but when I don't need O-ring, this is cheaper. netShop sells imported very cheap filters, but DAYTONA is not the same as those, and I think the filter paper is well made. View detail
I think it is a good value for money.
I think it is very easy to wear and has a good appearance and texture for the price. View detail
Satisfied
Cost-effective, but if you don't buy Large size, it's Small size View detail
Smartphone Folder to be expected to be durable in the future.
I had heard that attaching a smartphone to a motorcycle would damage the camera's autofocus, so I did not install one even after purchasing a motorcycle. However, recently I have been touring more and riding on unfamiliar roads, so I decided to install a folder. It is easy to install and holds the phone firmly. The parts that are subject to force are made of aluminum parts, and the durability of the Folder itself seems to be promising. I installed it on the Left Side of the Handlebar, but since the eye movement while driving is Large, it would be safer to put it in the Center. Whether this product is really good or not depends on how long it will protect my phone. View detail
Fits: HONDA CROSSCUB110, HONDA CROSS CUB50, HONDA SUPER CUB110, HONDA SUPER CUB110PRO, HONDA SUPER CUB 50, HONDA SUPER CUB 50PRO
Cost-effective!
This is a must-have Items for CROSS CUB Oil replacement. All packing and filters to be replaced are included, and the discount is very reasonable. I use CROSS CUB for touring, so I replace the oil only about twice a year. So I replace Packing and Filter every time. I will continue to repeat this service in the future. View detail
Fits: YAMAHA DRAG STAR 400, YAMAHA XSR700, YAMAHA XSR900, YAMAHA TRACER900, YAMAHA TRACER900 GT, YAMAHA BOLT, YAMAHA MAJESTY250, YAMAHA MT-07, YAMAHA MT-09, YAMAHA MT-25, YAMAHA MT-03, YAMAHA MT03
Just right Custom
I installed it on my YamahaBolt and it looks great with the Round Type, a little less visible than the OEM but not hard to see. View detail
Small
I bought it for my BMW R1150GS because it fits VST 1050, but it is smaller than I expected. I bought it knowing that it would not fit over the SIDEPannier, but I did not expect that it would not fit over the Top case either. The storage is compact. View detail
Fits: KAWASAKI GPZ1000RX, KAWASAKI GPZ1100, KAWASAKI GPZ900R, KAWASAKI Ninja ZX-10, KAWASAKI ZZR1100, KAWASAKI ELIMINATOR 750, KAWASAKI ZEPHYR1100, KAWASAKI ZEPHYR1100 RS
DAYTONA Oil Change Perfect set
Would buy again.
because it's easy
View detail
DAYTONAFilter wrench
I bought it for my motorcycle, but I can also use it in my car. View detail
Fits: HONDA CBR400R, HONDA CBR600RR, HONDA CBR650F, HONDA CBR650R, HONDA CB650R, HONDA CB250R, HONDA 400X, HONDA CB125R
Blue sky reflected in the Mirror
The purpose of purchasing the product was to improve rearward visibility when merging lanes.
Immediately after receiving the product, we started installation. First, check the approximate position by placing it on the OEM Mirror. After degreasing the mounting surface, peel off about half of the protective seal on the double-sided tape of the Mirror to be mounted, and slowly apply the tape,
One SideIt took about 5 minutes. The dimensions show a slight gap, but it did not bother me at all while driving.
I bought the Blue color this time and I think the color is good. I went out after noon and the sky was a little white, but when I looked through Mirror, I saw the reflection in the Blue sky as seen in the picture and it lifted my mood. Unexpected effect. I have not driven at night, but I feel that the visibility is not bad even when driving in the tunnel, and I do not feel dazzled by the headlight of the car behind me.
View detail