My first Hydration

I bought this to go on a real OffRoad course.
I was advised by a friend of mine that I definitely needed one, so I chose one that was in Manufacturer stock.
The contents are exactly as shown in the product image.

When you want to drink water, just slide the Stopper on the tip, and it was easy to drink water even for the first time.
The capacity is 2 liters, so it can hold all the large size plastic bottles sold at Convenience.

The equipment is easily removable with the one-touch button on the chest, and the size was perfect, easy to carry on the back and not get in the way while riding.

It is also a simple bag, which can hold simple tools, and the Tool pocket is Magic tape, which can also be easily attached and removed.

I was able to remove the Water Pack part and clean it with dish detergent as shown in the product image.
I was told that they are prone to Mold if not taken care of, but they are easy to wash, so it's not difficult.

It feels safe to use and has no resin smell.
There is also a Guide to pass the Hose through the Belt, so I had no difficulty in handling the Hose.

However, I'm not sure how far the cleaning will go, so it looks like it's better to fill with cold water than SportsDrink.

With the authentic EnduroCourse, it's easy to raise your body temperature and understand the importance of this product as you said.
I think you can equip it without a sense of discomfort because it is easy to match the look and various Off-roadJersey. View detail

Anyway, it's light.

In combination with this Hand guard and ARCLever.
It's running.
The strong Hand guard is able to make a small contact with a standing tree, etc.
The Handlebar will be taken and
It has a certain weight, and the Handling becomes sluggish.
Because I don't like it.
Plus Tik's elasticity is quite high.
Even if you fall down hard, there will be no damage to the Large.
Recommended View detail

Used for off-road motorcycle riding

When I was riding my off-road motorcycle on the forest road, or when I was riding over logs or obstacles, my palm that gripped the handlebar was under a lot of strain, and I often got blisters on my hands.
I bought this product to prevent blisters from forming on my hands.
I was worried whether I would feel uncomfortable putting on Gloves because I put on Gloves after putting on my hand, but it was a good impression that I could install Gloves without feeling uncomfortable without inhibiting.

It may be suitable for on road long distance touring.
If you get blisters on your hands when you ride Motorcycle, you might want to give it a try. View detail

You protect Silencer from Wound.

[How is it used?
I did not want to damage as much as possible the PowerBox of SP Tadao for SEROW250 which I purchased with a feeling of resignation, and installed it.
Was the one you received as per Image?
Heat-resistant material for easy installation on Silencer of any cross-section:It was as Image without discomfort for Rubber.
Was the installation difficult?
It can be easily installed by anyone because it is only wrapped around the part that wants to be protected from the fall Wound and fastened to the front and back evenly etc. with Tie Band of the attachment.
How was your experience with it?
I have fallen over more times than I can count since I installed it, and the Silencer has not been scratched, and has been well protected with the other Guard (the Silencer mounting bracket has been bent inward from too many falls, but the surface of the Silencer is intact).
[Included Parts:were they on?
Tie BandQuantity for fixing in addition to Body:Comes with 2pc.
[Was there anything that disappointed you?
After purchasing this product. "It's a fake, as close to the same shape as you can get. I was disappointed in the price difference too much.

0Other items that may be useful include
Point and hang of installation
Wrap it around where you don't want it to hurt and secure with Band! It's very easy, so don't hesitate to try it.

[With or without Instruction Manual
I don't think there is an Instruction Manual, sorry if there is.

[Easy to understand]
I think it's very clear that the product is exactly what it looks like.
Personally "Good thing I kept it on." This is a product that I can truly believe in.

[Notes]
It depends on how you fall, but if you fall hard you might be able to wear a Tie Band to secure it.

[ITEMS TO BUY TOGETHER
This product alone will not cover the entire Silencer, so you may need additional guards depending on how your motorcycle is used (I have them on the front and back of the Silencer).

[Opinions and requests to Manufacturer
Do you think a cheaper price would stop customers from drifting to the fake ones? View detail

Effective, but Large to put on and take off.

[How is it used?
I have seen several photos of Boots rubbing and peeling off the Frame paint, so I installed this as a countermeasure.
Was the installation difficult?
The O-ring? that comes with the frame is used to secure it to the frame, but I had a hard time because the gap to pass it through is very narrow.
How was your experience with it?
I feel that Frame is well protected.
However, dirt and water accumulate between the Frame and Protector, so it needs to be removed and washed periodically, but it is Large strange to attach and remove…. View detail

I can't think of anything else.

[How is it used?
I like to play with Enduro, and I like hard things, so I throw machines, drop them, and fall in hard ways.
In the past, I installed ZETA's hand guard on the bracket that grows from ZETA's Stem, and it was a solidly spec. that never turned the hand guard. However, the Solidly Spec. which ignores the flexing characteristic of the Handlebar is tired and causes the arm to rise.
I was looking for a hand guard that would protect my levers without interfering with their bent characteristics, and I found this one.

Was the one you received as per Image?
It is as per Image. Or rather, it is the third.

Was the installation difficult?
It's easy, you're right about Bracket going around the bottom of MASTER. Sometimes I see brain-dead people who put it through the top.

How was your experience with it?
The Handlebar flexes even when closed! It also has the strength of a closed handlebar! It turns with the master, so neither the master nor the hand guard will break! It doesn't break even if you roll it with a lot of force!
And it's the best. Let's get rid of the aluminum hand guard.

[Included Parts:were they on?
Not particularly

[Was there anything that disappointed you?
Not particularly

Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
I would be happy to buy Repair Parts. View detail

ACERBIS Super motard front fender

I think the product is solid and well made, but the moment I opened the bag, it was not as glossy as the other company's parts. It was the worst.
Can you return these things? LOL! View detail

Stable ACERBIS!

Easy to install, only takes 5 minutes, looks great and functions well. View detail

Effective for on road vehicles

[How is it used?
Used mostly for city driving (commuting). Introduced as a measure against the cold in winter.

Was the one you received as per Image?
I had previously purchased a light cowl from ACERBIS and felt that the texture, etc. was worth the price, but
No problems with this product either.
If I had to say, the screw on the inside of the guard (Lever side) is Silver color and a little cheap.

Was the installation difficult?
I think it's easy to install, just insert the Bracket and tighten the Bolt.
Only Honda cars? Or, because it is Large strange to take the Bar End and Inner Weight.
I think it will be how we get through this.

How was your experience with it?
It worked much better than I expected.
Even with the Winter Gloves & Grip heater, the back of my hand would get cold after riding for about an hour.
It's getting harder, but the driving wind is much less likely to hit me, so sensibly the cold on the back of my hands has dropped by about 90%.
Thanks to this, I can ride comfortably with 3SeasonGloves & Grip heater without using thick Winter Gloves.


[Included Parts:were they on?
It had several kinds of collars for adjusting the gap with Bar End.

[Was there anything that disappointed you?
None in particular View detail

For EDRace and MX practice.

It is easy to get blisters on the Left hand, so I use it only on the Left hand. Damage of the hand decreases surely when I put it on, but I think that it is good to divide it into consumables and to use it because it becomes quite ragged in 3~4 months. View detail

Avoid Troubles That Make You Unable to Drive

The Chain Slider seems to be common to almost all of Yamaha's recent OffRoad racer models, so it can be diverted.
I have been using them for almost 10 years on my YZF, YZX and WRF.

OEM Material:AluminumBlock bends when it hits a rock or a tree, and in the worst case it becomes impossible to drive.
I bought this because my Chain Slider was bent and the Chain that came off almost split the Crankcase.

The quality is very high.
What I want to mention is that the bottom part is fastened with 4 hexagonal screws because of the 2 piece structure, but the distortion of the screw mountain does not appear at all even though it is a small screw and the point where the impact is frequently applied.
Material:A female screw like "Brass" is embedded in the body side of Plastic, but every time I do maintenance, the screw goes in smoothly and I am surprised.
Of course, the maintenance such as applying waterproof grease has been done.
As for the body, the wound became a lot as expected, but there is no particular deformation and it is possible to use it normally.

There is no rubber in the contact area with the Chain, and I thought that the durability might not be able to be expected because the resin of the Chain and the Body touch each other directly, but it seems that it can still be used with little wear unexpectedly.

I don't know much about material engineering, but the surface of the body is decorated with Carbon Style pattern, but the body material is probably DURAGON? I think the body is made of a material like DURAGON.
Personally, I like the Material made by ACERBIS:Plastic products seem to be good products.

The only thing that bothers me is that there is no rubber on the Guide, so when the Chain is strung loosely, it rattles a bit like a large fine-meshed rattle. I got used to it soon.


This is a recommendation for those who do not want to retire in a race, those who must return by themselves on a forest road, and those who want to protect their Crankcase from trouble.
It's also a good choice for those who plan on keeping their Yamaha vehicle for a long time because it can be used interchangeably. View detail

When you use thin Gloves, you can use something that can reduce the vibration and

In the speed range, such as high speed, it does not go as expected.
But for everyday use, I think the vibration is reduced.
It may seem like a hassle until you get used to it… View detail

It's sturdily made, which helps.

I used it because my friend who rides Africa Twin was using it.
With the weight of the CRF250L, a normal Hand guard will turn in almost one shot.
I replaced it almost once a year. So far, I've fallen over a few times.
It's not deformed. It seems to be long-lasting and helpful. View detail

Whether to choose Poly sports

I installed this on my 2016 YZ250FX.

Material:There is another PlasticFrame protector made by Poly sports, but the mounting method and materials are almost the same.
The prices are about twice as different.

One of the biggest differences is that ACERBIS uses a different material, black resin, for the area where the boots hit, to improve the heel grip.
I spec'd both frame guards, and it's true that ACERBIS's grip is a little bit higher than ACERBIS's, but I couldn't feel any large difference in my level.
I remember that the difference of Grip was a little more large in the new state, but the difference gradually decreases because the surface is worn with fine scratches after repeated use.

Material:It is plastic, but I think durability is high because there was no damage at all even if I used it for 4-5 years.
Poly sports made is also still about 1 year old Spec. so durability is unknown, but it looks not bad.

Tie bands and anchor bolts are included in the kit and can be installed without any problems. However, the tie band for the rear brake master cylinder is not tight enough and it slips every time I drive.
Because the body doesn't come off especially, I only put it back when I get a gap, but I think that the dust adjustment around Master Cylinder is a little weak.

There is only one point to note when using this Protector.

There are several CushionDamper on the FrameReverse side, but if you use it for a long period of time, it will leave a mark on the Frame side that cannot be removed by PIKAL.
It is recommended to use cushion material such as Sponge when installing the Protector.

Protector's defense is high enough.
It also prevents a lot of damage from falls as well as chafing of boots.

I think it is a good part to install even if you think about the resale value for a long ride.

By the way, if I washed the car normally, there was no mud left between Frame and Protector. View detail

Stylish Protective Parts

I installed it on my RSV Silencer.
It's so easy to wrap and tighten with Tie Wrap.
Material:Silicon is thick enough to provide protection in the event of a fall.
I also like that the Design is Stylish. View detail

Dress-up parts to get you in the mood!

I added the Bar pad which is a standard part for Off-road motorcycle.
I chose ACERBIS because many people wear Renthal.
It's always in view, which makes me feel so much better! View detail

Is 14.5Liter capacity about 2Liter practical?

capacity ： There is a 14.5 liter cargo space/2.5 liter Hydro bag included.
Hydro bag full Tan with 2 Bath towels and 3 Hand towels!
It has a cylindrical shape and is carried in an unstable situation.
Each Belt can be adjusted to your preferred mounting position.
I was disappointed because I was expecting the capacity of a regular Knapsack, but
I use it as a water tank with Pocket. View detail

crf250rally ACERBIS X-GRIP FRAME PROTECTOR

My 2020 crf250rally has a hose fixing bracket on the left part of the frame, so it's a bit misaligned, but it fits well when I press it with force. fixing bracket on the left side frame, so it doesn't fit well, but it fits well when pressed with force. It is made of plastic and is mounted with a cable tie. View detail

I want people who suffer from blisters on their hands to try this.

[How is it used?
I have been suffering from blisters on my palms caused by the grip and gloves rubbing against them even when I am wearing RACING Gloves during Circuit driving. At first, I tried to cover it up with taping, but the taping didn't work very well because the Gap and the gloves got torn up very quickly …
I'm sure it's a matter of how you ride, but I found this product when I was trying to be patient and keep riding.

Was the one you received as per Image?
I received a product with the same Design as the image. In the image, it was quite PeLePera, and I thought that the border of the finger and the finger might be torn immediately, but there was not the feeling that it tore immediately when I felt it pulled.

How was your experience with it?
The RACING Gloves I'm using are RSThailand's "NXT052 GP-WRX The size selection is the same as Gloves, Large Size. In fact, when I tried to put on the RACING Gloves with Palm Protector, there was a little stiff feeling around the palm, but I got used to it immediately.
As for operability, the vital finger is bare, so there is no Large change.

The most important thing is the effect, but so far it's been good without any blisters on my hands. However, I feel that Palm Protector is rubbed instead, so I will see how durable it is. I think it is too much if it lasts 1Season because the price is cheap. (Lol)

Also, I personally think it will be good for protecting the leather because the sweat from my palms won't directly touch the RACING Gloves. Leather that absorbs sweat tends to harden and become tattered, so this is not the original effect, but it will help the Gloves last longer.

[Points to note]
When you put your hand into the RACING Gloves, make sure the Palm Protector is tightly fit or it will sag and feel strange in the Gloves. Pull the Palm Protector tightly to your hand before putting your hand into the Gloves.

How did it compare to other products?
This is my first time with this product so I have no comparison products. View detail

Material:Plastic but durable

I used it for about 5 years.
I bought a new Mount and used it on the next vehicle I switched to.
I think that durability is high because there is no large-scale damage though there is whitening by Wound and mud on the surface as expected though I do not use it so hard.

When you install the Disk guard, the benefit of the protection of Caliper as well as Brake Disc is large. The Caliper piston returns to ScauperScauper by finger even if Seal is not changed. I think it is protecting from mud and water.

By the way, the OEMACERBIS Mount is a little annoying because the Dust Seal on the Wheel often falls off when removing and installing the tire even if it is new. The quality is also a little low.
The ZETA mounting kit is totally pimped out.
The texture of the aluminum processing is higher than the one made by ZETA, and the rib of the Wheel Collar is effective. The photo shows the Mount which has been used for 5 years (90h), but there is almost no deterioration.

By the way, the Mount of ACERBIS is a structure that the collar part and the Mount part become a separate body, and the Guard moves round and round before tightening, but it can be fixed by tightening the Wheel nut.
ZETA is all one piece structure, so you can adjust the position by moving the mount and tighten the wheel nut to fix it.

Personally, I think the ZETA is better serviced with the Mount as well.
Please refer to this page when you purchase Guard and Mount separately. View detail