Reviews
Quite a back view Refreshing
I installed this on my Ninja 400 2018. I really didn't like the back view and wanted to make it Refreshing.
It was made to look quite Refreshing and the visibility of the Blinker was fine. The Installation Instruction Manual was easy to understand.
I had a fair amount of trouble installing it. However, there is quite a lot of information about it on blogs, so I don't think I made a mistake.
First, the screws on the Blinker Bracket were too tight when removing the OEM.
I know it's a Kawasaki thing, but before you start lambasting Screw, here's the Shop. (Note that it was equally hard on ZrX1200DAEG, so be careful if you have common or similar Parts)
If you want to use Bullet Terminal for the connection after installation, you don't have to do any modification. In my case, the OEM was the connector, so I cut off the Bullet Terminal and installed a separately sold connector with Electric Works Pliers.
View detail
Compliance with Laws and Regulations
Installed on a last model CB400SF. (Molds after 2019)
Legal restrictions such as the angle of the Number are strictly enforced depending on the year and the time of first year registration.
This product is sturdy enough to comply with vehicle inspectionsLarge because it is compliant with angles and other requirements.
However, we have been told that some DREAM stores may uniformly consider Motorcycles of the regulated year as Fender EliminatorNG,
In the meantime, I decided to keep the Normal fender as well.
I did the work by myself and was able to complete the work without hesitation due to the detailed Instruction Manual. 8mmSocket, 10mmSocket, 3-4-5mm Hexagonal, 10mmSpanner, Radio pliers, thin Slotted screwdriver
The keyhole for the SeatOpening is different from that of other Fender Eliminator models. (Prayer is all we can do now.) …
It generally took about an hour.
Design and finish,
There is no Japanese Vehicle Inspection Correspondence for the latest regulations other than this one, so there was no choice. I did get the Refreshing, but I give it a 3 star rating.
Ideally, I would like it to be a little higher, further back, and angled. I don't have a choice.
The accuracy of each Part is high, and the Laser marking in Small is just right and gives a sense of ownership.
You will also want to change the Blinker.
View detail
So-called Caliper Adapter
This is a fitting part for the brake system, but unlike the general banjo adapter, it is a part that is directly attached to the stainless mesh brake hose (#3).
In addition to cutting the hose, shaping the end faces, and forming the wires, it is necessary to accurately insert the internal parts called Olive to prevent the socket from falling out.
The level of work difficulty is quite high.
Failure to do so will result in the Brake slipping out and dying, so it is painful unless you understand the structure and are quite confident in your detailed work, or you have experience in making Brake hoses many times.
If the hose is assembled in a way that is easy to assemble, the effect of the hose reinforced with stainless mesh wire will be lost, and you will end up with a disappointing hose that is better than a rubber hose...but only a touch better than a rubber hose.
The angle cannot be adjusted after assembly as is the case with the Banjo adapter type, so it is necessary to consider the direction and angle from the time of assembly.
It takes a lot of hang to put it together well, and there are very few amateurs who can do it well.
Fortunately, I have experience in the past in producing 200 hose kits a day for a certain company, so I am very familiar with this fitting process and can freely assemble them in 5mm increments.
The Banjo adapter type would have eliminated such difficulties, but why bother using the troublesome Olive type?
It's a Type that I think lighter and Simpler is Cooler.
It's a world of complete self-congratulation, where the loud, anodized, lumpy, hardened Hose hates Large.
The part number indicates that it is an authorized Goodridge product.
Banjo made by Goodridge is thinner than those made by other companies, which is good for a stylish finish.
I don't want to use banjo around the Hydraulic Clutch, so I have made all the oil lines with a fitting system, but then I can't use a common banjo bolt.
This Adapter replaces the Banjo bolt and connects the fitting to the Master Cylinder, Caliper, or Release cylinder.
One Side is a #3 ANSize (3/8x24) to match the Fitting, and the other is a Spec. with a choice of Screw Pitch and Convexity to match the target.
While the other Parts part numbers are GoodridgeOEM Product numbers, this Adapter is not, and is not a GoodridgeOEMParts.
(GoodridgeOEM has a groove at the apex of the hexagonal part where the wrench hits in the case of millimeter pitch.)
But well, such a thing can be easily made by cutting a hexagonal bar, cutting a Screw and matching the Taper angle, so there is no problem even if it is not GoodridgeOEM.
In fact, it can be said that the carefully crafted surface finish and Screw cutting, which can only be achieved by domestic production, provide higher performance than GoodridgeOEM.
In this case, Quantity:Pair (for Left and Right) Caliper and Clutch on the Master Cylinder side of the Clutch.
(The release cylinder side of the clutch is made of GoodridgeOEM material that was left over on hand.:Aluminum, since it is the part that does not move, we decided to use aluminum.)
Performance is Perfection.
The precision is still good, and there is no Screw snagging that I feel with the GoodridgeOEM.
The price should be finished at a lower price and this is a RECOMMENDATION.
View detail
No amateur Brake hose for homebrew
This is a fitting part for the brake system, but unlike the general banjo adapter, it is a part that is directly attached to the stainless mesh brake hose (#3).
In addition to cutting the hose, shaping the end faces, and forming the wires, it is necessary to accurately insert the internal parts called Olive to prevent the socket from falling out.
The level of work difficulty is quite high.
Failure to do so will result in the Brake slipping out and dying, so it is painful unless you understand the structure and are quite confident in your detailed work, or you have experience in making Brake hoses many times.
If the hose is assembled in a way that is easy to assemble, the effect of the hose reinforced with stainless mesh wire will be lost, and you will end up with a disappointing hose that is better than a rubber hose...but only a touch better than a rubber hose.
The angle cannot be adjusted after assembly as is the case with the Banjo adapter type, so it is necessary to consider the direction and angle from the time of assembly.
It takes a lot of hang to put it together well, and there are very few amateurs who can do it well.
Fortunately, I have experience in the past in producing 200 hose kits a day for a certain company, so I am very familiar with this fitting process and can freely assemble them in 5mm increments.
The Banjo adapter type would have eliminated such difficulties, but why bother using the troublesome Olive type?
It's a Type that I think lighter and Simpler is Cooler.
It's a world of complete self-congratulation, where the loud, anodized, lumpy, hardened Hose hates Large.
The part number indicates that it is an authorized Goodridge product.
Banjo made by Goodridge is thinner than those made by other companies, which is good for a stylish finish.
Now, this 3Way is the Parts to branch the Hose.
There are a few examples of T-shape with 3-way, but usually the Straight fittings are stuck from three sides.
That way, I don't have to worry about the twist angle of the Hose, etc., and it's easier to assemble and install.
Many products that appear to have only a Socket can freely rotate the Socket part and do not need to worry about the twist angle.
In such a situation, this Parts is Olive type, so there is no such convenience!
The twist and length of the hose that sticks in from three sides must be matched EXACTLY in order to use this difficult part.
Moreover, this is with Bracket for Mount.
Since it is assumed that this PARTS is fixed, the lack of room and deception is maximal.
But when it's finished, Parenthesis is great, isn't it?
The intent and skill of the creator of these parts are obvious to those who know what they are.
It is for Large people.
View detail
That's what Active is all about!
I purchased ActiveSupport along with my brembo equipment. I personally like this manufacturer and the quality and price are very attractive. I am very satisfied with the center and the quality of the product. It may be a little expensive, but it is a product that you can be satisfied with once rather than losing money buying a cheap one. View detail
I wanted a Size notation.
I bought it to use for bremboRear caliper center out, but the bolt size was for M10.
RearCaliper bolt cannot be used because it is M8.
There is no Manufacturer notation, only thickness, and I would like to see at least Bolt diameter indicated.
It is now in the collection of Parts.
View detail
Fits: SUZUKI HAYABUSA
When it comes to Fender Eliminator, it is Active!
There are various Fender Eliminators sold by various companies, but Active's Fender Eliminator is well made and the material is thick enough. The price is not cheap, but not expensive either. It's a sure thing. View detail
Used for GALESPEEDBillet Axial Caliper
Used to install GALE SPEEDBillet caliper.
Necessary parts for integrated Breeder/Hose installation.
Double/single use depending on h-type brake hose routing.
CaliperBlackI wanted to create a unified look, so I chose P1.00Black.
We considered other companies' products, but the combination made by Active and GALE SPEED is a safe choice.
View detail
Fits: HONDA REBEL250, HONDA REBEL250S EDITION, HONDA CL250
resolving a severe earthquake
The tremors from 90 km dramatically disappeared and I am not tired at all even when touring long distances. View detail
With Fender Eliminator Kit
I purchased this kit along with the Fender Eliminator Kit.
It is a Slim shape, so it is good for Refreshing.
Installation is nothing difficult as it is simply inserted after the License Plate.
View detail
To Active's Wire.
I used it on Active's Accelerator Wire. It is a little Large compared to other Manufacturers, so it binds FirmlyWire. I recommend this product because it is beautifully made. The price is reasonable. View detail
Washer I use all the time.
It is used for GSX-R1100.
Often used for maintenance of Front brake, Clutch and Rear brake.
The relatively low cost and the choice of the number of sheets to purchase ensures that there is no waste.
I have used it many times now and have never had a problem.
View detail
Purchased for installation of Brembo caliper
I bought this product to install Brembo caliper. The texture is good.
RightLeft and backside engraving for installation (Landmarks) It would have been nice if there had been a detailed Instruction Manual that would have helped me understand the installation orientation. I had a little trouble installing it. (Is it just me?)
View detail
Stylish finish
I have purchased Active's Fender Eliminator Kit for every car model so far, so I chose this one again.
Installation requires touching Blinker's Wiring, so if you want to install it yourself, you will need to have at least a minimal knowledge of this area.
The product itself is solid and I have no complaints about its accuracy.
The only thing I would say is that Reflector is a security component and should be included in the package.
View detail
Buy at Dress-up
The hook is too large for a loading hook, so it is difficult to hang a belt on it, but it looks good. However, I think the price is too high for a loading hook only. View detail
So bad
Wire adjustment screw on handlebar side of 1 pc out of 2 is not tightened from the beginning.
When I tried to remove the protective cover of the middle wire adjustment, the Outer Crimp on the adjustment bracket fell out.
It's a shame because I have been using Active's High Solo for a long time on another motorcycle and I trust it.
View detail
It can be installed without modification on the '24 MODEL.
Although there is currently no support for the 24-model ZX-6R, the model numbers of the OEM RearFender and License lamp are the same as the 23-model, there were people who installed the LED Blinker on the day of release on SNS, and even when the Z900 was not compatible with the LED Blinker, there was no problem installing the LED Blinker. I bought it because I could install it on my Z900 without any problem even though it was not compatible with the LED Blinker.
As a result, it was possible to install the equipment as per the Instruction Manual without any modification, including wiring, etc.
Since the exhaust device was still installed, we had to work while shifting the servo motor, but it was not too difficult as long as we had a tool with an extension baret, which is easy to apply force.
The angle is sweet with the Japanese Vehicle Inspection Correspondence, but it is a lot cleaner with the elimination of the lopsided Rear Fender.
Note that Reflector is not included and must be prepared separately.
I have installed a type of License Plate Holder that can be attached to the bottom of the Posh Reflector, which was also used on the Z900.
View detail
Simple and easy to use Throttle kit
[How is it used?
The Separate handle forced us to change the switches, so we introduced the Throttle kit.
Was the one you received as per Image?
I am satisfied with the quality, Anodized's Throttle case is easy to scratch….
Was the installation difficult?
It is not particularly difficult, and if you are a good custom player, it is easy. However, the carburetor side of the Throttle Wire is difficult.
How was your experience with it?
It is a regular Throttle so it is no different than OEM. No resistance and I am normally satisfied.
[Included Parts:were they on?
It is possible to install the kit alone, but the length of the Throttle Wire may need to be replaced or considered for crawling in some cases.
[Was there anything that disappointed you?
Case is easily scratched, Bolt rusts easily.
I would have preferred High Solo if I was going to go through the trouble of replacing it.
View detail
Brake fluid replacement
Used for brake fluid replacement. Although it is a little expensive View detail
Same shape as Fanatic
When we converted D Tracker to Terminators, we chose this Handlebar because Renthal's Ultra-Low, which was one of the candidates, is out of print. It has the same shape as the previously released Fanatic aluminum handlebar. The aperture is shallow and we were able to create a low position. View detail