Cost performance is the best as Universal!

If you purchase the end rubber at the same time, you can use it with most of the M6 Bolt Rear Sets' Change Pedal and Brake pedal. View detail

Cost performance is the best as Universal!

If you purchase the shaft at the same time, you can use it with most of the M6 Bolt Rear Sets' Change Pedal and Brake pedal. View detail

Simple is the best!

From NORMAL
It was quite Refreshing!
Design is
I like it very much!
Installation is not difficult.
Due to the large number of Bolts in the structure
We need to think about the order of the tasks.
It may take some time.
Once installed.
It is quite sturdy and sturdy.
Shaking while driving or
I didn't think Bracket would break! View detail

Peace of mind for a long ride.

It is made by Gee Craft, a trusted manufacturer, so there are no problems with accuracy.
There are similar products at about half the price, but I was not sure if they were accurate enough, so I chose this product.
I think it is Large sturdy as it is OEM, but it is also a place that is frequently stressed, so there is a sense of security in terms of reinforcement.
We could not experience any shift change due to the installation.
If you expect the ScauperScauper feeling of *Change, you will experience it better with the Clutch adjustment. View detail

Excellent

Hello everyone, this is a good product and I recommend it to everyone. This product can play a better role in braking .This is 100% original, you can buy with confidence. View detail

Braque is …in JAPAN!

It's Brake related. There are made overseas at half the price, but …hey….
Rather than regretting it later, I chose something that I could use with peace of mind. I am satisfied & relieved. However, I thought that the cutting marks were rather conspicuous, as was the front support. I was not disappointed with the Objection. Maybe it is because it is a hard material. View detail

It doesn't change. It's more like...

Originally, JA65 had little Shaft exposed, and I wasn't sure if it made sense, but I bought it.
The result was the worst.
The product was not parallel to the shaft and was slightly distorted and did not attach cleanly.
The small modification made it possible to install it properly, but it was a little heavy when shifting gears.
Even if the product and shaft are properly centered, about 300g more tread force is required.
The shifting fee ring doesn't change at all either. 4 people tried it and no one could figure it out.
It's like they commercialized it because it was a Hit at JA55. View detail

Things are good. The price is high.

Still for Rear SetsDesk, but we're running out of parts.
I installed it but it is not running again. View detail

Improved rigidity

It's been three days since I installed it.
I don't know if it has become easier to shift.
What is certain is that the long Shaft is compensated for and the rigidity is assured by the increased stiffness. View detail

I am satisfied.

I installed the GEAR because it was difficult to get in after the car was delivered. After installation, it is no longer difficult to insert the GEAR and it works well. View detail

Looks good.

Installed on an 88cc MONKEY with a new head. I chose this oil cooler because the external oil cooler is too messy. The effect is still unknown, but it should be better than no oil cooler.
Also, the standard Plug socket is too long to fit in the Plug replacement, and the Manufacturer also specifies Glasses Wrench. Please refer to the short socket we found. Part number HPW-3B-16 View detail

Manifold

Variable Manifold Accuracy is also good View detail

Easy installation and effective

I installed it on my Circuit Running car and it works well as a shift guide.
The installation itself can be done without any problem by those who can perform simple maintenance if they read the Instruction Manual properly.
No special tools are required.

When shifting the rod, does the shift rod itself bend when shifting the rod before and after installation? Does it wobble? Does the force escape? The feeling of the shift rod itself bending or wobbling when shifting has disappeared.
GEAR is now going into Smooth, so it feels good to run on the Circuit.

The price seems a little high, but this can't be helped because there is not much of the car in circulation as a model. View detail

Highly satisfactory!

From a certain company's thin Swing Arm until now.
Changed to GCraft.

First of all, it looks good!
The high price of this product is enough to give you a sense of ownership and satisfaction.

The installation requires a certain amount of skill since it is an undercarriage.
However, Special Tool is not required.

You can ride it, look at it, polish it, w View detail

Replaced from non-bearing.

The shift guide from another company that I had installed a year ago was no longer effective due to wear, and it was time to replace it,
This time, we purchased and installed this product with built-in bearing.

Both other companies and this GCraft product have the same Fee Ring, which is a straightforward GEAR.

Both GCraft and other companies' Shift guides Top 3 Best Parts for CUB Series Installation of the two.

GCraft's products are about three times more expensive than other companies, but if they are machined or have built-in bearings, the price is reasonable, and they do not lose their effectiveness due to shaving.
The instruction manual says that the footpeg can be installed without removing the footpeg if only the shift pedal is removed, but the spring of the collapsible footpeg is in the way, so the footpeg must also be removed.

However, I think Torque wrench is essential since it is a part to be installed around the engine. View detail

Now you can drink.

Anyway, Cool.
You can polish Motorcycle, look at it and have a drink.

The installation is routinely MONKEYRose and
Level is normal if you are a person who is doing Level.
Special Tool is also not required.

Well, I am satisfied visually. View detail

Convenient to have

It is not necessary to have it, but it is convenient to have it!
Stylish and cool when present! View detail

Cast Variable Manifold Indicator

Motorcycle MONKEY
Exhaust System OUTEXExhaust System Up Type
Tank OEMGORILLA
carburetor YOSHIMURA Mikuni TM-MJN24 Carburetor
Manifold + YOSHIMURAAngle Spacer

I bought it because the cook of the Fuel Tank interferes with the carburetor in the above Spec.

The angle of the carburetor can be freely adjusted so it no longer interferes with the Cook.

The Manifold is a little longer than the one made by YOSHIMURA, but I am satisfied with it because it does not interfere with the cook. View detail

When you are looking to Maximize Rigidity on the Grom

About quality and texture: I am happy with the quality of the engine reinforced plate from G-Craft. Made from aluminium and machined to allow for high strength and light weight. About the feeling of use: The engine reinforced plate allows for an addition connection between the engine and the frame which leads to a noticable reduced movement and vibration. Products to buy together: A set of steering stem stabilizers from Outex would also be desirable to purchase alongside the engine reinforced plate to also add some reinforcement to the steering. Difficulty of installation: The process to install takes about 20 minutes, position the engine reinforcment plate and install the 4 bolts into the engine followed by the 6 bolts that clamp the plate around the frame. Not difficult to do. Cost performance and comparison with other products: High costing but you are getting a beauitfully designed product made from quality aluminium stock. With there being no other branded product like this there are non to compare. About shipping and packaging: Sea frieght is my preferred method of shipping due to the lower cost and it is fantastic that it has returned as an option once again so I can put my money toward parts and not high shipping costs. Webike kept me updated on the status of my order up to when it shipped. The parcel arrived within the expected date range and was well packaged with no chance of the part being damaged. Any concerns, cautions, or advice when purchasing: I see no concerns or cautions to be advised of in regards to this product. If you are looking finely detail your Grom then go for it. View detail

Due to a change in position

I changed my seat to a Kitaco one before the season, but when I started riding...
I don't mind the footing, but when I run, I find myself leaning forward more than before.
I'm mainly a touring rider, so I like to ride in a relaxed position.
So I bought it.
It's not a particularly difficult process, since all you have to do is remove the handle and insert the product.
I bought the two centimeters up, and I think it was just right. View detail