It is easier to put in Neutral when stopped.

The one that makes it easier to get into Neutral, which you'll know when you use it. View detail

incomprehensible

Instruction Manual is too complicated and difficult for beginners. I think some knowledge is necessary. View detail

bremboIncluded Parts:for compatibility with

I bought a battered 900SS (900SL) and am Restore.
I scraped together various Brand components to make a footpeg, but as expected, the stop lamp switch did not look good.

I really wanted to use a mechanical switch, but I didn't want to grow a small bracket to hold the switch in place or to hook the spring, so I decided to use a hydraulic switch.
I hate Hydraulic Switch because it makes PedalTouch worse...
However, my ankle does not move very well, and it is impossible for me to step on the rear brake while cornering.

I was so quick to buy a Switch with Pitch 1.25, but this product is properly Pitch 1.00.
Everyone should make sure that the Pitch is correct before purchasing.

The shape is the Hydraulic Switch itself, which is included with the recent brembo RACINGMaster Cylinder.
The only difference is that the color on the wiring is blue while brembo's is red, but the construction and precision are no different from brembo's. The only difference is that the color on the wiring is blue while brembo's is red.
If I had to say, the condition of Mt. Screw is rough...? It's about the same.

I think the manufacturer is probably the same as brembo.
Then, by visual inspection and operation Check "Superiority." The determined items would go to brembo.
This Babyface product seems to be the next best Level product.
(95 point product that looks and works fine, but not as perfect as brembo)
My guess is that the very cheap Chinese Switches sold on Amaz0n are made in the same factory, and those that did not reach the passing line in the inspection (those of a level that cannot be sold as made by brembo or Babyface) are not disposed of and are being sold on the side.
I don't know.

Anyway, this product is normal and problem free.
It is working properly and stably.
Oh, but I was worried about Screw Pitch only, so I put it through Dice beforehand.
But it was only a part of the Plating layer that was caught, so it was Large sturdy Level even if it was used as it was. View detail

Casual Dress-up

For Front Axle Slider and Engine slider
I have Babyface on and a Stand Hook.
The same Manufacturer is used for this product. View detail

It protected me from standing moss.

I had the same thing installed when I purchased the vehicle. It was not the original purpose of the Slider, but it helped. I only replaced one of the sliders. When I was replacing it, I was playing with the one I had installed and the Black Anodized was peeling off. .... How is it in terms of quality? I feel like I have to ask myself, "How is the quality of the product?" But there are not many other options for this type of car. I just hope I won't have a chance to replace it next time. I am very happy with the quality of the product and the points it comes with. View detail

Expensive, but good

Although the price is high, the shape and dimensions of the mounting points are appropriate, and it fits much better than the ones I had before.
The design is good and satisfactory! View detail

I was able to install it on the 2023MODEL with no problems!

I am a 171cm tall male.
I am clumsy & mechanically challenged, but I was able to install it easily.
The position is fixed (one choice), but it is not at all uncomfortable.
It is now difficult to hit the footpeg without having to put your foot down forward when stopping.
The riding posture has become easier and my knees are not stiff even after riding for a long time. View detail

Keep the Style

If you keep the Tandem Footpeg attached, I think KIJIMA is better, including ease of use.

But if you want to make it a complete one-seater, I wouldn't hesitate to go with Babyface!
It's not easy to use, but you can't change the way it looks!
I am Large satisfied with my choice! View detail

Installed on CBR600RR (8BL-PC40) released in 2024

It was unclear if it would fit the CBR600RR (8BL-PC40) released in 2024,
Engine slider (item no. 006-SH041).

I'm a beginner, but how to remove Cowl and install Engine slider on Youtube,
By looking at it many times, I was able to install it without any problems.

Torque wrench, liquid Gasket, and Screw lock agent are required.
Digital Caliper helps in the selection of parts for assembly.

Photos are for reference only.
Since the body color is Matte Black, the base is anodized black.
I also wanted to make the slider cone a little more Large, so I changed it to L100D. View detail

Custom

Items we do not want to be indebted to you.
The appearance of custom feeling will be increased. View detail

It can be used occasionally.

Very small and cute keychain item. Great to carry on your bag or key. The quality of the Tone tool is also good. It is a good size for emergency use. View detail

a gift purchase

Very small and cute keychain item. Great to carry on your bag or key. The quality of the Tone tool is also good. It is a good size for emergency use. View detail

Opposite side of Silencer bracket

Since the Tandem Footpeg to which the Silencer was attached was replaced with a Bracket, it was decided to remove the opposite footpeg for balance.
Also, Rear Sets were recently changed to Babyface LargeHanGold, so the same color is used for this product.
Installation is not a lost cause.
Of course, Tie Down austerity seems to be bearable. View detail

Replaced from GALE SPEED due to spec. change.

Replaced from GALE SPEEDFoot controlKit due to spec. change.
GALE SPEED has a large number of cut-out parts, and although we liked their appearance very much, we had to give them up in tears due to a combination of other parts.
To be honest, as others have mentioned, I did not have a good impression of Babyface because of the cheap Boltetc. and the use of many Bolts for position adjustment such as Shift lever.
When the actual product arrived and I opened the package, I found it to be smaller than GALE SPEED.
It could be said that the chattiness of the product led to its lightness.
Parts are individually packed, and I liked it because I could tell if screws were over- or under-assembled during assembly.
Others have mentioned that the exhaust device drive wire interferes with the exhaust, but I have addressed this by wrapping the wire around the Colgate Tube as shown in the photo.
After the installation and test run, I wrote about how I thought it was too small and how I felt about it.
I was concerned that the use of a large number of Bolts might make it feel clunky, but there was no unreliable feel at all.
I knew it was because Babyface's products are designed to be used in Race.
I personally like the color Large Osaka Gold, but I thought it looked meh when I saw it installed on other people's motorcycles while touring, but when I installed it myself, it had a strong presence and lifted my spirits. View detail

Lightweight and Dressup

I installed the footpeg for the purpose of dressup after the removal of the footpeg, but unfortunately, I could not see the engraving, which is the most important part.
Other than that, I have no complaints. View detail

Divert to other cars

Sprocket cover on Z1000
Actually, the 900RS version is on its way.
I don't see it in the lineup for Z1000 because of its unpopularity.
The Z900 is based on the Z1000 Engine.
The Z900RS, which is based on the Z900, would have the same dimensions.
In other words, the Crankcase should be the same for Z1000, Z900 and Z900RS!
And when I tried to match it, I found that it was EXACTLY!
You did it!

Tightening was Torque managed using Torque wrench to no avail.
As for functionality, the Sprocket cover has a Shift holder, which might improve the Shift feeling.

And when I put it on, Wiring, which was hidden by OEMCover, was fully exposed, so I hid Wiring with Tube.
It's hard to see on the STAND side and nobody sees it, but it's self-satisfying.
This part of the hobby thing is the Large thing, isn't it?
It's a functional Part, but when you clean the Chain.
I like the fact that the FrontSprocket part, which was covered and couldn't be flushed with cleaning agent, can now be flushed directly.

Z1000 BaseEngine is ZX9R
In other words, the Sprocket cover for 9R should be able to be installed.
It's nice to be able to divert from a popular car model. View detail

good-looking

OEM is expensive, so we chose here.
I have not yet fallen over, so I do not know how effective it is.
I think it looks good. View detail

I am satisfied.

The texture is good and the Position is satisfactory.
You can select multiple positions, so you are sure to find one that suits you.
Knurl knurling is fine and grips well.


Instruction ManualFor those who are not familiar with Custom, we recommend that you install it in the Shop because it is difficult to understand.
It would be a little easier to understand if there was at least a Seal on the bag to indicate what part number is in the Instruction Manual. View detail

For countermeasures against release defects and for dress-up

[How is it used?
I was looking for the cause of the whining noise from the H2. I found many articles saying that the clutch release was causing the problem, and among them there was an opinion that Babyface was better than OEM, so I bought it.


Was the one you received as per Image?
I was surprised that it was 2 times larger than OEM. I was surprised that it was larger than OEM, but I was glad that the matt Silver was better than Image.


Was the installation difficult?
Installation is very easy with silicon grease and air bleed technique. Also, depending on the year, a gasket may be required.

How was your experience with it?
The squeaking sound is gone and the clutch is a little lighter at the same time. It is very good.


[Included Parts:were they on?
Gasket for Banjo bolt came with it, which is good. Also, Sticker is good. (?' ?) There is no Gasket to assemble the Release to the body, so it is necessary to buy one depending on the type of car.

[Was there anything that disappointed you?
I wanted to buy a black one, but I was disappointed that only two colors, silver and gold, are available in the lineup. I hope that other colors will be available in the future. View detail

Fits neatly

Gold, the symbol of Manufacturer, is very Beauty! View detail