Nice...

I replaced it with a Sintered pad because the Brake squeal would not go away and it was less expensive and seemed more durable.
The pad before replacement came with an unknown manufacturer, so there is no comparison, but it works and does not squeal as usual. 。
Control is much better than I expected, and the effectiveness changes with the amount of force.
It seems to be a bit aggressive to Rotor, which is a concern, but it was a good decision to replace it. View detail

Replace Red with Golden Pad

I have not been able to drive yet because of the rain, but I changed the pad as well as the Caliper OH!
I'm looking forward to running it. ('∀ `) View detail

It is not a pure Black.

The color looks a little brownish rather than black in the right light. It is super easy to install. I think you can install it by yourself, but if you don't have the knowledge to remove the OEM bar end, you might want to ask a shop to do it for you. The included Inner Weight is a few Grams lighter than the OEM. View detail

It was EXACTLY!

I purchased this to replace an OEM Oil cap groove that was broken.
It was Exactly in JA10! View detail

As expected of DAYTONA

Was the installation difficult?
pimping
How was your experience with it?
It's going to look different View detail

Dress-up in a casual way

It can be dressed up casually.
I am satisfied with the quality of the product.
It would be better if it were a little cheaper. View detail

Kagoshima Touring for 1,600 km

Saganoseki→Aso→Takachiho→Cape Sata→Nichinan and Kyushu Touring 1600 km or so, no problem! View detail

The oil filler cap is very convenient to use and decorate

Daytona brand is a famous brand in the production of spare parts for motorbikes from engines to decorations. In particular, the product set of oil cap, reservoir cap and bar ends comes from Daytona premium, I feel the quality is improved compared to normal Daytona. With this set of oil caps, compared to the original cap, I find that it is not only used for decoration with many colors to choose from, but also can be easily opened and closed to make changing the oil easier. With a normal OEM oil cap, I usually spend about 2 to 3 minutes opening and closing the oil cap. With the Daytona oil cap, it only takes 30 seconds to do that. View detail

Oil Filler Cap

Changed to Green Light or Gold. View detail

Casual Dress-up

For Front Axle Slider and Engine slider
I have Babyface on and a Stand Hook.
The same Manufacturer is used for this product. View detail

Shallow angle

It came with a 10° Handlebar, which felt a bit tight, so I bought an 8° Handlebar.
Only drilling of the switch box is required, but I am satisfied because the position is relaxed and the front load is not lost. View detail

2BL-SC54 is not compatible.

I purchased this product with CB1300SB2019MODEL.
The tank side is narrow and the cap side is wide, and the screw holes do not fit at all.
So I will return it.
I think the quality is good
I would like you to check it carefully before you describe it. View detail

cheap

[How is it used?
Oil replacement once a year
How was your experience with it?
I don't have a measuring machine and I don't know what it feels like.
How did it compare to other products?
The appearance is like OEM is expensive.
Functionally, is the amount of Filter inside more than OEM? And?
Gold is inexpensive and the Brand is a classic, so I personally feel secure.
[Points to note]
I think it's about conformity caution. View detail

DAYTONAOil Filter

I wanted to replace the oil and filter by myself, and after a lot of research, I found DAYTONA's products! I recommend it! View detail

Is there a problem with being thinner than OEM?

I'm sorry I couldn't provide a photo, but when I used it on my NINJA2 Helmet 50RSL, I compared it with the OEM one, and the shaft part that holds the pad is clearly thinner,
The measurements were taken from the OEM, so they should be the same diameter." This was the case
I have a question for those who are familiar with Brake, is there any particular problem with the thin shaft part?
Has anyone who bought the same Stainless Steel Pad Pin had a similar case? I would like to hear your opinion. Thank you in advance. View detail

PetitCustom

[How is it used?
It has a custom feel.
Was the one you received as per Image?
As you wish.
Was the installation difficult?
It's very easy.
How was your experience with it?
I like it at One point.
[Included Parts:were they on?
Hexagonal Lunch is not enclosed.
[Was there anything that disappointed you?
None
Other items that would be helpful
Remove Oil cap for NORMAL It is easy to install.
I wish it had come with a Wrench, but ….
The first step of the Custom project was the installation of the new system. View detail

More rust-resistant than OEM Product

I used this for an overhaul of a very old OEM Caliper. The previous owner had maintained it to some extent and it was not so badly worn, but I wanted to assemble it in a new and clean condition if I was going to overhaul it. I chose it because I wanted to assemble it in a brand new and clean condition. View detail

Satisfied with the price, although it is higher than OEM.

Easy replacement and Torque management. View detail

Peace of mind that it is made by MORIWAKI

The peace of mind of being made by MORIWAKI.

I don't have Level gauge, so I guess I'll go back to OEM just in case I need to replace Oil.

So far, no problems at all. View detail

Fits ZX-4R

It can be attached to ZX-4R without any problem. View detail