Easy to install, but ???.

Installation is easy, and the design fits well with the car body without any discomfort. However, I think that the reflector should be included from the beginning since ACTIVE also manufactures a reflector. View detail

It's easy.

Seal for easy installation!
The light blue reflection alone has a custom feel!
I loved it. View detail

Purchasing of this cam chain tensioner roller allowed for the continued use of my super chain chain tensioner

About quality and texture - The cam chain tensioner roller from SP Takegawa is made from a hard rubber bonded onto a steel center, the quality from the overall fit and finish is perfect. About the feeling of use - The purchasing of this cam chain tensioner roller allowed for the continued use of my super chain chain tensioner after the roller was showing signs of wear and saved my purchasing a complete replacement which is ideal considering the cost compared to the repair part. Products to buy together - Parts within the cam chain tensioner system suffer significant wear with engine upgrades that allow for much higher RPM riding and a key product to buy together with the cam chain tensioner roller is the cam chain tensioner push rod head that SP Takegawa also sell as a repair part. Difficulty of installation - The installation of the cam chain tensioner roller is an advanced task that took 1 hour to complete due to the disassembly of the engine required to access the area in which the super chain chain tensioner is installed. Mechanical aptitude and the use of a special tool and basic hand tools is what is required to secure the roller to the tensioner. Cost performance and comparison with other products - I find the cost of all the products SP Takegawa sell to be on par when compared to what most other companies sell their products and the cam chain tensioner roller is no different. About shipping and packaging - With there being no cost difference between sea freight and EMS for the cam chain tensioner roller, I chose EMS for an earlier arrival date. The part was extremely well protected while being covered in bubble wrap and surrounded with air pillows in a sturdy cardboard box. Any concerns, cautions, or advice when purchasing - Webike Japan is the first place I look to for all my motorcycle needs. From service parts to performance products and even motorcycle gear and apparel, Webike always seem to satisfy my needs in regards to availability and pricing. View detail

Worth the expense for the noticeable smoother and stronger pull through the RPM range

About quality and texture - The ignition coil from Kitaco is made from injection molded plastic with a red surface finish, the quality from the overall fit and finish is perfect. About the feeling of use - The ignition coil is worth the expense for the noticeably smoother and stronger pull through the RPM range with the added bonus of an improved appearance against the red frame on the Monkey 125. Products to buy together - A key product to purchase when upgrading the ignition system is an iridium spark plug to complete the transition from original to performance system efficency of iridium technology. Difficulty of installation - The installation of the ignition coil is an simple task that took 0.5 of an hour complete. Some mechanical aptitude and the use of basic hand tools is what is required to secure the ignition coil to th frame. Cost performance and comparison with other products - I find the cost of all the products Kitaco sell to great value when compared to what most other companies sell their products for and the ignition coil is no different. About shipping and packaging - With there being no cost difference between sea freight and EMS for the ignition coil, I chose EMS for an earlier arrive date. The part was extremely well protected while being covered in bubble wrap and surrounded with air pillows in a sturdy cardboard box. Any concerns, cautions, or advice when purchasing - Webike Japan is the first place I look to for all my motorcycle needs. From service parts to performance products and even motorcycle gear and apparel, Webike always seem to satisfy my needs in regards to availability and pricing. View detail

Very precisely made

Beautiful shaft, extremely well made, the fit is very precise and it gives a very secure feeling when torqued up, It greatly adds to the appearance of my machine, I'm very happy with it and I feel it offers good value, I also have the JB Power front wheel shaft and the JB Power swingarm pivot shaft, View detail

Car-specific installation kit?

As a result of the installation, there is a 7mm gap (see photo) at the Knuckle guard mounting point, and it rattles when driving.
This is happening because the thickness of the Color Guide for the car-specific installation kit is 12mm and Large!
In the end, to eliminate the 7mm gap, we purchased a K-CON M6 18Φ 5mm thick aluminum spacer and installed it to eliminate the gap.
In addition, the DL1000 V-STROMSX bar end attachment part is described in the instruction manual as a type that compresses the rubber between the bolt and the handlebar and crimps it to the handlebar, even though it is a type with a screw cut on the end of the handlebar (the parts list does not show such a construction). (Even the Parts List does not show such a structure.)
Thinking that perhaps a mounting kit for another model was mistakenly included, I inquired at the ManufacturerSite, but received no response (I was disappointed because I had been using the Manufacturer's Lever until now).
The quality and texture of the product are highly evaluated, but the mounting kit is not good enough.
Dear Webike.
Not because it was a SPECIAL PRICE. View detail

Tail Bulb replacement for KSR's Fender Eliminator Kit

I purchased a used KSR80, but the previous owner installed a Fender Eliminator Kit, and the tail lamp is a Lucas type.
There was a Trouble with Tail Bulb immediately after purchase.
I removed the Lens to see the model of the Lamp to replace it, but unlike the usual Double Bulb, the head was a Small Rhinoceros Bulb.
This Type was not sold at Home center or Car Shop 。 Maybe MotorcycleParts specialty stores have them, but I can't find any near me. 。
However, because the length of the Tail Bulb was different, it interfered with the Lens, causing the Lens to chip, melt, and consume more power due to its higher wattage.
I had put it off because it was inexpensive but the shipping and other things made it needlessly expensive, but I had some shopping to do at WeBig, so I bought it as a package deal.
After installation, there was no interference (obviously), and since the Watt number was lowered, the power consumption was also lowered, eliminating the concern factor.
I am planning to eventually switch to LEDs, but there is a barrier of full-wave rectification, so I may end up putting it off. View detail

Quickly to run

With the Front12T, you will be running Quickly, both on forest roads and in town.
It is affordable and I feel the effect of the replacement. View detail

You can trust me.

I bought it from another Motorcycle and had no problems, so I trusted them. View detail

People who like the NORMAL form.

Installation takes about two hours while carefully curing.
It is very easy to remove the cover if you do not pull it off and do not make the mistake of shifting it to the Front side.
The volume is moderate and not loud, and there is little change in the feel of operation and blowing. The weight is lighter, so there may be some benefit to this.
If you like the "I made it custom" look, this is the one for you! If you like a less "custom" look, this is a good choice for you. View detail

I was hoping?

In the product introduction photo, it looks like a Push rod Rubber.
I was expecting Large...
After installation, I checked and it was only half hit.
In the first place, half of them seem to be hit even in NORMAL.
I got the impression that there were a few more hit surfaces, but not as many as I had hoped for.
The construction is good, but it's not surprising considering the price.
Cost performance is poor
Hoping for a protective effect?
I gave it a 3 star rating. View detail

StyleUp is a sure thing, but the rider's body shape will affect the Riding.

The GCraft seat is a good choice for me because of the balance between the tank and the seat. The ground contact area of the seat is limited, so in a positive sense, the position is fixed and the stability is increased. If you are heavy or taller than 170cm, you may feel cramped. View detail

Engine Guard installed

Installation should not be a problem if you have some knowledge of maintenance.

An Engine Guard was added to protect the engine in the event of a runaway and to mount the Fog Lamp. View detail

LEDFog Lamp installation

I was worried about night driving with Headlight alone.
Fog Lamp has been added for peace of mind.

Installation is also secure because it can be fixed firmly. View detail

The weight of the description does not Ate.

OEM 3-type for horizontal JOG (480g) I bought it for the weight Up rather than the
The description gives a weight of 515g, but the actual measurement is only 496g.
OEMs usually increase or decrease by about 5g because of balance shaving, etc,
I could not think of writing an imprementation that I would recommend to others if the Cut-out Outer had an error of almost 20g!


[Regarding installation].
50cc horizontal JOG (3KJ/5AUCase before regulation, 5BM/5SUCase after regulation)
Case cover Gasket is required.
However, the shaft part is thicker than OEM, so when you stop the Nut, insert the O-ring, and try to close the Cover.
The gap with Bearing on the Cover will be insufficient.
So we need to take measures such as thinning the O-ring

・3WF
There's plenty of room to spare. o-ring should be as thin as the 50 story?
You can replace the Nut that stops the Outer with a thin Nut for 50cc View detail

Rigidity is up!

The Front perimeter will look Snap.
The fluffiness was significantly reduced and operation felt easier. View detail

Flashing switchCover

Very good!
The switch knob was originally shaped to be far away and difficult to operate for Small Saijapanese with hands, and it was a part that we had to put up with.
Push cancellation was easy and finally Refreshing.

If I may say so, it would be better if there is an arrow or some other prominent mark-like label or paint on the top surface. I applied seals, but the surface is matte textured, so seals tend to peel off easily. View detail

Just the right length.

Although I have not had the pleasure of using it on forest roads yet, I tested the actual pull on Garage and found that the thing itself was easy to grip and firm enough to lift the Front. View detail

No different than OEMs

Purchased due to leaking oil line. I am glad that the quality is the same as OEM and the price is lower. I will buy again when it breaks. View detail

After much waiting, it finally arrived!

Cool! I'm glad I put it on! ♪ (??????) ♪ View detail