Reviews
1P2014
The head lamp on my Honda Little Cub burned out. I liked the price and parameters of this lamp (not much power does not overheat the cartridge). Everything turned out to be good in quality, the lamp works perfectly. View detail
Advantages of Maintenance
I have been using DX since its release. I don't mind maintenance, but sometimes I get tired of doing it when I'm busy with the weather, so it's nice to have less frequent replacements. Fuel consumption and running performance do not change drastically. View detail
Easy installation, no brightness problems.
Until now, we had been using Type with LEDs affixed at the top and bottom, but the straightness of the LEDs was poor when Up is lit, so we always used the LEDs facing down.
This type of LEDs are affixed in the LeftRight type, so the straightness when the LEDs are up is also OK. This time, I installed it on a square eye light, but I think it would be best for a round eye light. Finally, I am satisfied with the brightness.
View detail
Control voltage is too high.
After installation, I casually applied a tester to the battery and found that 16V was output!
I thought it was quirky and expensive, so I measured it and found that both Regulator and Battery
Idling (1600 rpm) The control was at 16V at 4000 rpm and 17.5V at 4000 rpm.
This is not usable!
Idling when I put it back in the OEM that I removed it from. (1600 rpm) The voltage was 14.5V at 4,000 rpm and 16V at 4,000 rpm.
Wasted... Worst of all...
View detail
The size is just right and the texture is good.
Used in 2008 YZF-R1.
LengthSize is also really Exactly.
I did not originally intend to use parts cleaner, but I was able to get in without any difficulty without using Bond paint parts cleaner.
View detail
I got a lot of iron powder.
I used it to clean up my new MONKEY125. It was my first and second DIY oil change, but it was done without any problem. View detail
It's confusing.
When you purchase Slip-on Silencer.
Click here to purchase Gasket." I bought it together with the Full Exhaust System because there was a LINK with it, but it was a part that I would not use unless I was replacing the Full Exhaust System.
I learned from the Instruction Manual for the Exhaust System I received that a joint gasket is required for the Slip-on Silencer for the first time, so this product was a waste of time.
I would like you to put up a LINK to the recommended parts to purchase for the product.
View detail
Fits: HONDA DIOSR, HONDA DIO, HONDA TACT BASIC, HONDA ZOOMER, HONDA SMART・DIO Z4, HONDA SMART・DIO, HONDA STAND-UP TACT, HONDA SUPER DIOZX, HONDA SUPER CUB 90, HONDA SUPER CUB70, HONDA SUPER CUB 50, HONDA SUPER CUB110, HONDA GORILLA, HONDA CREA SCOOPY, HONDA QR50, HONDA BAJA, HONDA TODAY, HONDA TODAY DELUXE, HONDA CUB PRESS, HONDA MONKEY
No Impossible part
There is no part that is not possible as a Body Cover. View detail
Normal Mirror for mopeds.
ThirdMotorcycle's Today Mirror snapped off and I had to replace it. Very easy to read! Reasonably priced! … Too bad the Week Point is a little cheaply made…. "luxury" This is not for those who are looking for the best Mirror for their feet, but it is the best Mirror to wear on a foot scooter! View detail
OEM same etc., inexpensive and good.
It was used for the second Exhaust System removal and installation.
The texture was almost the same as OEM.
Since it is Gasket, the feel is comfortable.
Quantity:1 Set of 2pcs. so it is also cosmetically pleasing.
View detail
WhiteLight and good looking!
It's super easy because all you have to do is change the Valve.
I was able to purchase Valve's length and fit without concern because of the information provided by its predecessors.
D-TRACKER-X's dark, orange-tinged light has been brightened to white.
I haven't driven at night yet, so I haven't been able to experience the true effect, but the impression of the motorcycle will change considerably just by having white light.
View detail
Punching in as is
As per Title, it can be popped on as is.
Visibility from other vehicles, such as oncoming traffic, has increased, so I think safety performance has improved.
I don't know about durability so far.
View detail
Bright and low power consumption
I was worried about whether I could install it on my KSR2 since the body is longer, but I saw the impressions of someone who had already installed it on his KSR and he said it could be installed, so I bought it and installed it.
The length was a limit, but I was able to install it, the Others had no problems with the installation, and the rubber cover went on without modification.
The beam coverage has been widened. The optical axis remains the same and is large and sturdy. The high beam illuminates high up and is even brighter, so you have to be careful of oncoming cars.
I also changed the tail lamp to LED, so the power consumption was reduced a lot. I installed the LeftSwitch of the previous model in my car, so I can switch from LightOff to Light when Halogen is on.
Idling dropped about 200 RPM when switched to On, but switching from LightOn to LightOff when LED has no effect on Idling.
View detail
Cheap but good product
I purchased it as a replacement for the genuine Benley 110. You can't feel any difference.
Although it is cheap, I think it is a really good product.
I replace it every 10,000 km, but I think the replacement cycle could be longer.
I plan to continue using it.
-------------------------------------------------- -------- I purchased it as a replacement for the genuine Benley 110. You can't feel any difference. Although it is cheap, I think it is a really good product. I replace it every 10,000 km, but I think the replacement cycle could be longer. I plan to continue using it. Powered by Google Translator
View detail
OEM same etc.
Quantity:1 Set of 2pcs. to Spare when returning to OEM.
It's good enough
View detail
No problem, but...
Coupler is a little bit small and a little bit tight.
At first I thought I had the wrong part number because it didn't fit.
View detail
I put it on my RG 50Gamma.
It's just like changing a light bulb.
There is no problem
View detail
SP TAKEGAWA discharge bolt (w / magnet)
What are you waiting for? What are you waiting for? I want to know what I want to know. I want to know what I want to know.
Although it is not a visible part, this product is really good in that it can filter out iron powder inside the bike. The finish and design are wonderful. Thank you for the quick delivery. I would recommend this product to others. -------------------------------------------------- -------- It's not something you can see, but it's really nice to have this product to filter out the grit from the inside of the bike. The finish and design is great. Thank you for the prompt delivery. I would definitely recommend this product to others. Powered by Google Translator
View detail
Replaced with AJ59SUPER CUB110 Iridium plugs
To be honest, I don't know much about the effect of replacing it. 100% of the vehicles I have purchased so far have Windshield IRIDIUM in them.
I only feel that the Engine is working better, but that's OK, it's a world of self-satisfaction.
View detail
A well designed product that integrates into the factory engine case to add a useful feature
About quality and texture - The drain bolt with magnet from SP Takegawa is made from billet aluminium with precision machining and a red anodized surface finish while the quality from the overall fit and finish is perfect. About the feeling of use - The drain bolt with magnet is a well designed product that integrates into the factory engine case to add a useful feature that helps with engine longevity by removing unwanted metal from the oil. Products to buy together - A key product to buy together with the drain bolt with magnet is the SP Takegawa LED temperature guage that will allow for monitoring of the engine oil temperature to ad further longevity of the engine. Difficulty of installation - The installation of the drain bolt with magnet is a simple task that took 0.2 of an hour to complete. Some slight mechanical aptitude and the use of basic hand tools is all that is required to secure the drain bolt with magnet to the engine case. Cost performance and comparison with other products - I find the cost of all the products SP Takegawa sell to be on par when compared to what most other companies sell their products for but the drain bolt with magnet is priced higher this time round. The design of this drain bolt with magnet with it's sensor hole is what sets it apart from the others. About shipping and packaging - With there being no cost difference between sea freight and EMS for the oil filter cover, I chose EMS for a earlier arrival date. The part was extremely well protected while being covered in bubble wrap and surrounded with air pillows in a sturdy cardboard box. Any concerns, cautions, or advice when purchasing - For my location, purchasing specialty products like this from Webike Japan is the only option. There are a few local stores selling parts for the Grom but the range is very basic. View detail