Reviews
The knock pin are a part that do tend to sustain damage and is advisable to replace when this the case
About quality and texture - The pair of knock pins from K-Pit are made from steel and raw surface finish, the quality from the overall fit and finish is perfect. About the feeling of use - The knock pin is a part that do tend to sustain damage and is advisable to replace when this the case. This will ensure easier installation and removal of parts like the cylinder head, cylinder and crankcase halves when it comes time to overhauling the engine, as this is where they are used on the Honda Grom. Products to buy together - Key products to purchase when overhauling the engine would be gaskets and O-rings, all which are available from K-Pit here on Webike for the Honda Grom. Difficulty of installation - The installation of the knock pin is an simple task that took 0.1 of an hour to complete. Common sense and the use of your hands is all that is required to clean the mating surface and press the knock pin into place. Cost performance and comparison with other products - I find the cost of all the products K-Pit sell to great value when compared to what most other companies sell their products for and the knock pin is no different. About shipping and packaging - With there being no cost difference between sea freight and EMS for the knock pin, I chose EMS for an earlier arrive date. The part was extremely well protected while being covered in bubble wrap and surrounded with air pillows in a sturdy cardboard box. Any concerns, cautions, or advice when purchasing - Webike Japan is the first place I look to for all my motorcycle needs. From service parts to performance products and even motorcycle gear and apparel, Webike always seem to satisfy my needs in regards to availability and pricing. View detail
Genuine DID 520ERVT Replacement Chain Link
I always like to have some of these in stock in case of any issue during fitting different chains. The DID 520ERVT is one I do have in stock but have no spares. I found this chain link by just searching through the DID inventory on Webike website. It was really easy to find so you should be just fine. I ordered a few other different chain links along with this as I do like options with spare links. All were shipped together and this saved some shipping cost. My order arrived in 5 days from being shipped. The chain link came in a nice sealed packet with all that is needed to refit. You do get the white grease packet in this size chain so that's always a good thing, I have a lot of these anyway but you cannot have too many. The chain link is very well made one, it also is in the gold colour so nice looking too and it is also embossed with the DID logo so you know it's genuine. I keep the rivet link type and this clip joint type but had ran out of this version, hence the purchase. Very happy with these small purchases and these will keep me going for future. Thank you Webike. View detail
Refresh
[How is it used?
The front suspension of a VTR1000SP-2 I recently purchased was converted to an SC59 CBR1000RR. The front fender was forcibly installed from a VTR1000SP-2.
I bought this item to install a Front Fender for my SC59 CBR1000RR.
Was the one you received as per Image?
Insert it into the mounting hole of the Front Fender. A collar with a brim is then inserted and bolted to the front fender. The OEM parts are very well thought out.
How was your experience with it?
The usual HondaOEM Parts arrived. There is no doubt about it.
[Included Parts:were they on?
Not particularly
[Was there anything that disappointed you?
Not particularly
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
Rubber-based parts deteriorate, so it's a good idea to replace them periodically. They also protect the parts, so it is better to replace them before they stop functioning.
View detail
Genuine DID 520 Replacement Chain Link
I always like to have some of these in stock in case opf any issue during fitting different chains. The DID 520ERT3 is one I do have in stock but have no spares. I found this chain link by just searching through the DID inventory on Webike website. It was really easy to find so you should be just fine. I ordered a few other different chain links along with this as I do like options with spare links. All were shipped together and this saved some shipping cost. My order arrived in 5 days from being shipped. The chain link came in a nice sealed packet with all that is needed to refit. You do get a not seem to get the white grease packet in this size chain but that's ok, I have a lot of these anyway. The chain link is very well made, it also is in the gold colour so nice looking too and it is also embossed with the DID logo so you know it's genuine. Very happy with these small purchases and these will keep me going for future. Thank you Webike. View detail
For CB250F
.Actually this item i could not found in my country (VX Series Joint Link 520VX3). Finally I bought it from webike. It is original. Very good packaging.fast shipping.I am happy to deal with the webike team View detail
For CB250F
Genuine product FuseF (10A)(MINI 98200-41000 About quality and texture genuine product Cost performance and comparison with other products Good value for money. About shipping and packaging Fast shipping and very good packaging. highly ercomended. View detail
Changed from Clip to Crimp
When replacing the chain on the KLX230R, the ERVT came with a clip-type joint, but the clip didn't fit well and I had to press-fit it too much and it failed, so I decided to use a Crimp joint, which I am used to.
I think the Crimp is fine for me, and the Crimp is easier to work with because I'm used to it.
View detail
Fits: HONDA CRF250R, HONDA CRF250RX, HONDA CRF450R, HONDA CRF450RX, HONDA CRF250X, HONDA CRF450L, HONDA CRF450X
The Swing Arm side was distorted and it was very difficult to install,
The hole positions are the same as OEM, but the thickness may be different, and I had a lot of trouble with the gap in the hole positions when actually installing the product.
As a result, a workaround was to reuse the OEM Bolt. The bundled Bolt could not be used.
However, since the body was used and there were signs that the underbody had been hit, it was a little difficult to tell.
The product itself is secure with a Rubber underside to release impact, and it seems to avoid the Trouble that OEMs would quickly distort.
The product itself is usable, and the installation is a bit of a lost cause, so I gave it 4 stars.
View detail
Fits: HONDA CRF150R, HONDA CRF250R, HONDA CRF450R, HONDA CRF250RX, HONDA CRF450RX, HONDA CRF250X, HONDA CRF450X, HONDA CRF450L, HONDA CRF450RL
When OEM is not readily available.
I bought this one in stock because the OEM was Timing which was not readily available.
There are naturally no problems with performance, quality, etc., and we have the peace of mind of being a DRC.
Thank you for treating OEM Equivalent Product as a niche for Motocrosser as well.
Racer has a low Oil capacity and will be replaced as soon as possible.
View detail
23CRF250L replaced with WidePeg
WidePegQuantity for OEMAccessories:I gave up and considered alternatives because Set was still an 8 month wait.
I decided to purchase ZETA because I trust the quality of ZETA.
Due to the press-fitted Pin, the Wide effect is reduced compared to the Image of the Body.
Since the OEM footpeg is also quite wide, the actual front-to-back length of the Pin and the OEM footpeg tread width are +10mm.
It is true that it is relatively wide, but it is hard to deny the impression that the Body is unnecessarily large and heavy.
The feel is not bad.
I think it is also possible to shave the AluminumBody as it is and process it into a mountain wave.
I am satisfied because the texture is wonderful, just like ZETA.
View detail
Fits: HONDA CRF450RX, HONDA CRF450X, HONDA CRF450R, HONDA CRF450L, HONDA CRF250RX, HONDA CRF250R
Forged, solid feel.
The OEM was slightly bent, so it was replaced. Since the vehicle was used, it was aggravating to refresh these parts!
OEM is in reserve.
It is not a Lever with a particularly adjustable tip, and the Foldable portion does not change functionality all the way to the bottom.
The red color will eventually fade, but the black anodized body part is a good match to the Motorcycle's color!
I think I will replace it again because it bends a lot when I use it Hard.
View detail
Fits: HONDA CB250R, HONDA MONKEY125, HONDA CBR250RR, HONDA CB300R
It's more upscale, but it's self-serving.
All the vehicles I've ever owned have been in these Type Caps.
I came to replace it.
I have just purchased a MONKEY125 and I purchased this item.
I chose MORIWAKI because the Exhaust System is also MORIWAKI, and I aimed for a sense of unity.
It's really rated 4.8, but −0.2 is that Screw uses OEM.
If you buy a cap in Black color, you won't mind, but the one I chose is not in Black color, so the Bolt is floating.
I am trying to find a Bolt in Stainless or Titanium.
It is my favorite place to ride and I always see it.
Also, I think the purchase price is an easy price to choose.
View detail
Custom Black color
[How is it used?
The current NORMAL is Black, so I bought it to make it Colorful!
Was the one you received as per Image?
Yes, the product was exactly as shown in the Image.
Was the installation difficult?
It was easy to remove the Normal cover, remove the Filter inside, and install it on the purchased product.
How was your experience with it?
The Handlebar area is now brighter.
[Included Parts:were they on?
It was originally a Single Item, so there was no need for it to be a Single Item.
[Was there anything that disappointed you?
There is none
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
I had to be careful not to get brake fluid on the body of the car when removing the inner filter and installing it on this purchase.
Instruction Manual is also included in the package, so you should be able to install it with a good look.
I don't have any requests.
View detail
Fits: HONDA CRF250R, HONDA CRF250RX, HONDA CRF450R, HONDA CRF450RX, YAMAHA YZ125, YAMAHA YZ250, YAMAHA YZ250X, HONDA CR125R, HONDA CR250R, HONDA CRF1000L, HONDA CRF250X, HONDA CRF450L, HONDA CRF450X, KAWASAKI KX125, KAWASAKI KX250, YAMAHA WR250F, YAMAHA WR250R, YAMAHA WR250X, YAMAHA WR450F, YAMAHA YZ125X
Brake hose clamp and Quantity:Blue in Set
WR looks good with Blue parts anyway, Parenthesis is good.:We recommend the Blue color as a set. It is made of high-strength aluminum, so it is hard and does not deform even with large torques, and it does not chip easily. View detail
FOR CB250F
Actually this item i could not found in my country (Emblem,Production 86150-KPG-901). Finally I bought it from webike. It is genuine. Very good packaging.fast shipping. Thanks to the webike team. highly recomended. View detail
FOR CB250F
Actually I could not find this item in my country (Key, Blank 35121-MAS-G01). Genuine key, reasonable price, good packaging.very nice.Thanks to the webike team.good for the genuine buyers.highly recomended. View detail
Genuine Honda Rear Piston Seal Set for CB1000R 2011
These was a set of replacements for a broken piston seals for the CB1000R I have in the garage. I found that a few of the seals were not in great condition but these ones actually split and deteriorated. I purchased a set so I now have spares if any are still ok already on the bike. I found the correct part using the help pages and links that Webike provide. All with some other parts were shipped and delivered to my door in 5 days. These are small seals and do need a little care when being shipped. No problem at all for Webike, they put them in a nice bubblewrap envelope and were already on the Genuine Honda packet anyway. They were kept flat so there was no damage to the seals. As I already had the caliper apart for servicing, this set of seals were super easy to install. They arrived in perfect condition and had enough flex to be able to seat correctly. All back together and now that is one of the jobs completed. Thanks Webike, great work. View detail
FOR CB250F
Genuine key, reasonable price, good packaging.very nice.Thanks to the webike team.good for the genuine buyers.highly recomended. View detail
Fits and stable
I order new Honda OEM radiator cap with part number 19037-GEE-710 to replace for old radiator cap of Honda VFR 800 VTEC 2003. The old rubber that had aged is no longer closed, the new cap has fitted and stable. View detail
RubberSIDE
The installed product was badly deteriorated, so it was replaced with a new one.
It is good that the same HondaOEM Product is available, but it is somewhat expensive for a Rubber part.
View detail