Reviews
Driveline Refresh
Replaced for drivetrain maintenance. It was not so much to replace it, but I replaced it in a good mood. After the replacement, I did a test drive and felt that the acceleration was better. View detail
1P2014
The head lamp on my Honda Little Cub burned out. I liked the price and parameters of this lamp (not much power does not overheat the cartridge). Everything turned out to be good in quality, the lamp works perfectly. View detail
Anyway, it's bright.
The ADDRESS V100 has a reputation for having a dark headlight to begin with. (1994 model) attached to the
I am impressed that I can now see in front of me when driving at night, but in general, the light intensity is just normal.
Still, it is hard to believe that it is +6.5W, and you can feel the difference between just a light bulb and Halogen very clearly.
We do not yet know how durable it will be, and we do not know if the increased power consumption will affect the battery charge.
Well, even if the Battery goes up, you won't be able to leave because the KICK is on.
Its Risk is unknown, but I think it is worth changing it once for V100Owner who has problems with Headlight.
That's how bright it is! V100 is w
View detail
Easy installation, no brightness problems.
Until now, we had been using Type with LEDs affixed at the top and bottom, but the straightness of the LEDs was poor when Up is lit, so we always used the LEDs facing down.
This type of LEDs are affixed in the LeftRight type, so the straightness when the LEDs are up is also OK. This time, I installed it on a square eye light, but I think it would be best for a round eye light. Finally, I am satisfied with the brightness.
View detail
WhiteLight and good looking!
It's super easy because all you have to do is change the Valve.
I was able to purchase Valve's length and fit without concern because of the information provided by its predecessors.
D-TRACKER-X's dark, orange-tinged light has been brightened to white.
I haven't driven at night yet, so I haven't been able to experience the true effect, but the impression of the motorcycle will change considerably just by having white light.
View detail
Bright and low power consumption
I was worried about whether I could install it on my KSR2 since the body is longer, but I saw the impressions of someone who had already installed it on his KSR and he said it could be installed, so I bought it and installed it.
The length was a limit, but I was able to install it, the Others had no problems with the installation, and the rubber cover went on without modification.
The beam coverage has been widened. The optical axis remains the same and is large and sturdy. The high beam illuminates high up and is even brighter, so you have to be careful of oncoming cars.
I also changed the tail lamp to LED, so the power consumption was reduced a lot. I installed the LeftSwitch of the previous model in my car, so I can switch from LightOff to Light when Halogen is on.
Idling dropped about 200 RPM when switched to On, but switching from LightOn to LightOff when LED has no effect on Idling.
View detail
I put it on my RG 50Gamma.
It's just like changing a light bulb.
There is no problem
View detail
Perfect bolt-on side stand for NQ50 Spree
This side stand was easy to mount, and fit perfectly! It is exactly what you need if you AF-16 swap your honda spree! View detail
subtle
Perhaps it is because the Scooter has a low power generation rate, but I feel that the Halogen bulb has a wider beam range and better visibility.
This might be better with a slightly better Halogen bulb.
View detail
KITACO KITACO Non Fade Brake Shoe
2Quantity as it is used for CANOPY:Set was required.
I just installed and used it, so I don't know how durable it is yet.
Brake's gain has improved.
View detail
KITACO Non Fade Brake Shoe
I just installed and used it, so I don't know how durable it is yet.
Brake's gain has improved.
View detail
It works well
This is a 2007 ZOOMER.
The mileage is about 6,000km as I only drive it occasionally, but the Brake squeal was getting worse, so I replaced it.
At first, the effect was not so good, probably due to the lack of hits, but then it started to squeak.
When I disassembled it, I found that it was still on one side, and after licking the perimeter with a file, it looked better.
I am satisfied with the soft but firm feeling of working well.
Durability is not yet known.
View detail
Headlight LED
Installation was easy. It was brighter than I expected. View detail
OEM Equivalent Product, cheaper than OEM
Used for LITTLE CUB.
The low beam ran out, and a short time later the high beam also ran out. I bought this one because it was an emergency situation and it was immediately available in stock. The standard is 25-1. The Pine Stripe part number is 1P2015.
The grade of the bulbs is also the same as the OEM, White Hot bulbs, not Halogen.
I also found HalogenType, but the price difference was about three times as much, so I decided to go with the cheaper version.
Replacement is Light rim bottom, Quantity:Pair (for Left and Right) Remove the screw on the Plus of the light rim and lift the light rim upward to remove it.
The Glass part is replaced while touching as little as possible. Time required:2 minutes.
It lit up with no problem. I am relieved. I don't know about the durability yet, but it is a long-established domestic product and I am sure there will be no problem.
View detail
Very good Touch!
This is a 2008 ZOOMER.
The mileage was only about 5,000 km and it was still usable, but it started to squeal and work poorly, so I replaced it with a reliable Daytona.
It took some effort to remove the rear tire nut, but I am satisfied with the soft touch and effectiveness.
Durability will be confirmed in the future.
View detail
Used on a 50cc 2Cycle moped. Quite bright!
I originally used M&H Mats Stripe Halogen bulb 12V35/30W Clear, which was brighter than OEM, but still old mopeds are still dark.
Since I use them for commuting, I decided to use LEDs for safety reasons.
Installation can be done simply by removing the headlight cowl.
The color is a beautiful White and the brightness feels 1.3 to 1.5 times brighter.
The white color is more like a recent vehicle than the yellow color, which makes it a better parenthesis.
I think it is a good cosmetic product because it is inexpensive and made by Mats Stripe, which is a reliable company!
I use it on my AF35LIVE DIOZX, but the Valve is PH7 because I replaced the Headlight with an external one.
View detail
Clutch meatTiming could be changed.
I needed this clutch when I installed a Chamber and set the Weight Roller to a lighter setting. At first, I replaced only the spring with a Reinforcement Type one, but it didn't work, so I bought this Reinforced Clutch. I bought this Reinforced Clutch and the effect was so strong that I got sharp acceleration. To get the effect, you need to remove the Pulley and Wrench to remove the Clutch center nut. View detail
It's brighter than a white-hot bulb.
Installed on a Honda NSR80.
The NORMALWhite heat bulbs in the NSR80 were very dark, so we replaced them with LED bulbs to make nighttime driving somewhat safer.
If anything, it is not for the purpose of illuminating the road surface, I'm here, Appeal." I think it is highly satisfactory if you consider that LEDs for
In NSR80, the heat sink part of the Light case and LED Lamp is the contact limit. There is no problem.
View detail
Fits: HONDA CB125, HONDA CBX125, HONDA DJ-1, HONDA gyro canopy, HONDA TLR200, HONDA Super Cub 50, HONDA Lead 50, HONDA Lead 90, PGO MyBuBu125, SUZUKI K90, SUZUKI street magic, SUZUKI birdie, SYM fighter150, YAMAHA Cygnus, YAMAHA Cygnus, YAMAHA jog, YAMAHA jog sports, HONDA CBR125, KYMCO SOONER100, HONDA WAVE125
Product # 1P2004
One of my friends has a rare YAMAHA Town Mate 6 volt motorcycle. He was faced with the problem of finding incandescent headlamps. We are very lucky that this product is available in the webike. The workmanship is good. Great price. View detail
Fits: HONDA ROAD FOX, HONDA LEAD110(EX), HONDA LEAD 50, HONDA LEAD 50, HONDA VOCAL, HONDA BENLY50110PRO, HONDA BENLY50110, HONDA FLUSH, HONDA PAL, HONDA DIO110, HONDA DIO110, HONDA TACT Basic, HONDA TACT Basic, HONDA TACT, HONDA TACT, HONDA TACT, HONDA TACT, HONDA TACT, HONDA Tacty, HONDA ZOOMERX
Just size for old Motorcycle
HondaA-AF09Courreges TACT used in 85 years.
I was worried about the availability of KITACO products since I have a very old motorcycle, but I am glad that KITACO has their products.
When I removed the Exhaust System and saw it with the original, it was Just size and really helped me out.
The old Gasket is an old 2Cycle and I thought it was too large when I removed it, but it was attached to the exhaust system and I was able to remove it quickly with a slotted screwdriver.
The Gasket itself has the same structure as the OEM parts and is KITACO's product, so we can use it with confidence.
I have only driven about 100Km after installation, but I have tightened the bolts and there is no exhaust leakage.
I would like to say thank you to KITACO for continuing to stock Parts for old cars.
View detail