Reviews
1P2014
The head lamp on my Honda Little Cub burned out. I liked the price and parameters of this lamp (not much power does not overheat the cartridge). Everything turned out to be good in quality, the lamp works perfectly. View detail
Just receive item
Second time order from webike..the quality of packaging still tip top for me with the bubble plastic and so on..well order again in future..thank you View detail
The weight of the description does not Ate.
OEM 3-type for horizontal JOG (480g) I bought it for the weight Up rather than the
The description gives a weight of 515g, but the actual measurement is only 496g.
OEMs usually increase or decrease by about 5g because of balance shaving, etc,
I could not think of writing an imprementation that I would recommend to others if the Cut-out Outer had an error of almost 20g!
[Regarding installation].
50cc horizontal JOG (3KJ/5AUCase before regulation, 5BM/5SUCase after regulation)
Case cover Gasket is required.
However, the shaft part is thicker than OEM, so when you stop the Nut, insert the O-ring, and try to close the Cover.
The gap with Bearing on the Cover will be insufficient.
So we need to take measures such as thinning the O-ring
・3WF
There's plenty of room to spare. o-ring should be as thin as the 50 story?
You can replace the Nut that stops the Outer with a thin Nut for 50cc
View detail
rear impact
I am very satisfied with the high-quality packaging and the work of the shock absorber, my weight is 100 kg, it holds the road well and does not sway on the pits. I recommend View detail
Clutch outer replacement
APRIO (4jp5) The clutch outer of the "M" was worn and slippery, so I bought it for a replacement.
I had changed only the clutch first, but it started to slip a little when starting off, so I decided it was time to change it.
Inside of Clutch outer (Clutch contact surface) However, the old one was smooth as if it had been mirror-finished, but the new one had the same rough pattern as the surface, so I thought Clutch had a good bite.
I haven't done a test run yet after the replacement, but I don't think it will be a problem since there are no problems with the original running.
Outer clutches are supposed to be replaced when the color of the clutch burns out, so from now on, the clutch and the quantity:I will change it with Set.
View detail
Don't leak.
Fluid will smear.
Mr. Manufacturer says there is no problem.
Diaphragm Plate should be present.
When I replaced it with DAYTONA, it didn't leak.
Is it Large sturdy if I get a new Diagram Flum?
But I'm not sure since I can't leak at the moment.
View detail
Selected Gold as an insert color
The OEM filler cap from Mission oil was a milk-white color and looked too much like a dowdy cap, so I replaced it with this one! View detail
It is necessary and sufficient
Installed on 4JPAPRIO.
It was an APRIO that was given to me and originally had a Chinese Shock that I didn't understand, which was rusty, hard, and uncomfortable to ride on, so I bought it for the purpose of improving the ride quality.
I don't know the status of the OEM, so I can't make a comparison.
The spring rate is variable, so it is softer in the beginning and becomes stiffer as it shrinks, improving ride quality.
Product image is Quantity:The picture shows 2 pcs, but what you will receive is 1 pc.
View detail
Very happy
Was skeptical at first, but gave it a shot. Ordered 1 to ship to Oklahoma. Received item in a timely matter and it's what I wanted. Will be ordering from them again. Thank you View detail
Improved performance with reliable lightweight!
It is definitely lighter than the original and has larger ventilation holes, so it is by far superior in heat management and improves response. I am satisfied with the packaging, finish, performance, and price of the product. Since it is a product from a company with a long history of data, I was able to use it with confidence. Thank you. View detail
This is absolutely necessary!!!
Of all the items I purchased while tuning the B.Wiz 100, this is the item that gave me the most satisfaction. I was very satisfied with both the packaging and the finishing performance of the product. Since the settings can be changed without removing the clutch, the work time was significantly reduced, which gave me great satisfaction. View detail
Excellent pads
About quality and texture
The brake pads were chosen for Yamaha Vino; this brand has already been tested more than once in harsh urban braking conditions, so the choice immediately fell on them
The quality of the linings is high, they are dust-free, even after 5000 kilometers there is a minimum of brake dust in the drum
The glue is not visible, but there is enough of it, the sizing is very good
About the feeling of use
Operation on the next scooter showed its best side, braking is effective, even though it is a drum brake
With the correct cam setup, the brakes grab instantly and hold the wheel perfectly when pressed hard.
The average service life is about 10-15 thousand in urban conditions with frequent braking
Products to buy together
The kit includes everything you need, brake pads and springs
Difficulty of installation
Easy installation, you need to remove the muffler and rear wheel, then replace the pads
Cost performance and comparison with other products
Low cost compared to the original, and the braking quality is approximately 1.5 times higher
About shipping and packaging
Excellent blister packaging, no damage during delivery
Any concerns, cautions, or advice when purchasing
I can only recommend this product, already tested with three scooters ---------------------------------------- ------------------ About Quality and Texture The brake pads were chosen for Yamaha Vino, this brand has already been tested more than once in hard urban braking conditions, so the choice immediately fell on them The quality of the linings is high, they are unbearable, even after 5,000 kilometers in the drum minimum brake dust Glue is not visible, but it is enough, the gluing is very good ABOUT THE FEELING OF USE Operation on the next scooter showed itself from the best side, braking is effective, although it is a drum brake With proper tuning the fist, the brakes are grasped instantly and hold the wheel perfectly with a strong press The service life of an average of about 10-15 thousand with urban conditions with frequent braking Products to Buy Together The kit has everything you need, brake pads and springs Difficulty of Installation Light installation, it is necessary to remove the muffler and rear wheel, then replace the pads COST Performance and Comparison with Other Products Low cost compared to the original, and the quality of braking is about 1.5 times higher ABOUT SHIPPing and PACKAGING Great packaging in a blister, damage during delivery is not Any Concerns, Countions, or Advice When Purchasing I can only advise this product, already tested by three scooters Powered by Google Translator
View detail
Replaced with a new one
This Manufacturer is a Repeater, it is cheap and can be installed without any problems, just like OEM Parts! View detail
Crack cracked and replaced
First of all, it is cheap! This is good enough, I was able to install it without any problems. Just my personal opinion. View detail
Stable KITACO
I used it to replace the main jet on my APRIO4jp5.
The OEM-style chamber and High Speed Pulley were running well, but I had to go out for a short distance on a very cold early morning during the New Year's holiday, even though I usually only travel short distances, and my piston started to hug.
I changed to OEM #72→#76 because I thought the fuel mixture was too low because the auto choke was working properly.
Compared to the original sound, the exhaust sound became more bass-like, and we concluded that it was still slightly thinner.
When the PistonCylinder is eventually damaged, we plan to Bore up the PistonCylinder, so this product will be useful in that case as well.
View detail
NORMAL style with good cosmetics and a slightly better looking Exhaust System
It is an OEM-style, Polished looking, normal performing Exhaust System.
Gasket is also included.
The M6 bolt at the attachment point with the cylinder tends to be tightened because it is floating by the thickness of the Gasket, but it can be easily threaded off, so it is better to use a torque wrench to manage the M6 bolt to the M6 specified Torque.
It is a good cosmetic product, but the low price is partly due to the price, and some rust has appeared after two months of outdoor storage.
We replaced it with the company's Bore Up Kit (60cc) at the same time, so we have not been able to compare stand-alone performance, but we think the Level is fine.
The Motorcycle was given to me and originally had an inexpensive external exhaust system, so the sound level was almost the same.
I'm glad I bought it because it looks OEM-like, looks good and is inexpensive.
View detail
Necessary and sufficient.
I bought it for Setting.
4.5gSpec. and measured with a scale calibrated with weights, the error is sufficient to be at mostLarge0.03g.
The Body has the same shape of Both Sides, which does not seem to be oriented to the Body.
Durability is unknown, but I haven't seen any reviews that say it's bad, so I guess it's not a problem.
View detail
Used for CHAPPY
[How is it used?
YamahaCHAPPY (CHAPPY) Used for
OEM has discontinued the product and Vesra is available as a compatible product, but it was somewhat expensive, so we were looking for something NTB could use and found this product.
I was worried because there was no OEM Product No. for this product in the compatibility information, but there was an impression that it could be used with BOBBY, so I bought it thinking it would work. As a result, I was able to use it without any problem.
How was your experience with it?
No special tools are required for replacement, as it is simply hooked up and installed.
The positioning notches and Size feel were also similar to the OEM shape.
The car has not been driven in earnest yet, but after installing it and pushing and pulling it, it seems to be working perfectly fine.
Spring also came with a new one, so it was nice to be able to renew it.
How did it compare to other products?
As you can see in the photo, it was originally an OEM Product. (296-25331-00) was attached, but it was in RustRust condition due to a long period of neglect.
It was clearly better than that, so I am satisfied.
[Points to note]
Not particularly
【Review】
We were able to get a new Brake Shoe at a lower price than expected.
Life has not been tested, but for the price, I would be satisfied even if the amount of life is reduced a little bit.
View detail
Good
I think that the range of setting on the Secondary side will also be expanded. I think they are seriously considering the performance. The weight is lighter than the previous product. View detail
Exactly
Size is Exactly on the Groms, Case is always removed so I don't use it in that state, Base is fine left on. The fabric is neither thick nor thin. View detail