Reviews
Maintenance.
I have not used it yet but the Bolt on the R1 has rusted so I bought it to replace it.
I would recommend everyone to replace it before this happens because it will make the Brake less effective. LOL!
View detail
Original buffer rubbers
The rubbers on my VN800 Classic were old and crumbling.
I ordered these rubbers to replace the defective rubbers. These rubbers are a perfect fit and easy to install. ---------------------------------------------------------- The rubber on my VN800 Classic was getting old and crumbling. I ordered these rubbers to replace the defective rubbers. These rubbers are a perfect fit and easy to install. Powered by Google Translator
View detail
Fits: KAWASAKI KDX200R (for competition), KAWASAKI KDX220R (for competition), KAWASAKI KDX250R (for competition), KAWASAKI KL250, KAWASAKI KLX250ES, KAWASAKI KLX250SR, KAWASAKI KLX300R, KAWASAKI KX250, KAWASAKI KX500, YAMAHA WR250Z, YAMAHA YZ250, KAWASAKI KDX200SR, KAWASAKI KDX220SR, KAWASAKI KDX250SR, KAWASAKI KDX200, KAWASAKI SUPER SHERPA, KAWASAKI KLX250R (for competition)
DRCFront sprocket
It was just the right size. This is also adjusted by Rear sprocket. View detail
I've only driven about 100km ….
I replaced Red Pad with this one.
I drove about 100 km for now and it works normally.
No wonder.
This may be more suitable than Red Pad, which is more aggressive because it is an off-road vehicle.
The only thing that I thought was different from the Red Pad was that it locked easily when you stepped on it with a thud, but I don't think it did that….
It may be a Large cutoff to lock, but I'm afraid to lock it so easily, so maybe this is as good as it gets.
View detail
Slightly Mild than Red Pad?
I replaced Red Pad with this one.
The previous one locked easily when I stepped on it with a thump, but this one did not lock, perhaps because it is somewhat mild.
Since it is an OFF car, I don't think it would be easy to lock it, so this level of gain may be just right.
View detail
Replace instead of overhaul 20 year old OEM
The MAJESTY 250 OEM Master Cylinder is 20 years old, the paint is peeling, the fluid level window is white and cloudy, and the touch screen is dead. I thought that if I replaced it with OEM, it would be in the same condition again someday, so I replaced it with this one, which has better accuracy and quality.
The original vehicle had some customization done to the exterior, and the replaced handlebars gave it a more custom look.
I am satisfied that the color of the handlebar matches the color of the MASTER and Lever, creating a sense of unity.
Unlike the OEM, the 6-step lever play adjustment is also highly satisfactory.
Also, we are happy to be able to strengthen the brake with the SKULL Helmet principle by lowering the diameter by 1 Size to 11mm, compared to the OEM MASTERPiston diameter of 1/2-inches.
The brake hoses were stainless steel mesh when they were installed, so we did not have to worry about a large increase in stroke volume, and both control and braking power were improved, resulting in a highly satisfactory brake customization.
View detail
A little short, a little thick
I installed it on a ZrX1200ZrX1200 DAEG and it was a little short in overall length.
I think 125mm is just right. i bought some Sponge from Home center and filled the gap.
The thickness is about 33mm compared to about 30mm for OEM. It is just right for me. It may be too thick for some people.
View detail
New Master Cylinder while replacing Lever.
[How is it used?
The Yamaha MT-25's Brake lever had been made in China since delivery and I was concerned about rattling.
I was worried about using such a product in Brake, but I was wondering what to do because OEM products are too expensive and other brand products from proper manufacturers are expensive. I was wondering what to do. I realized that if I just refurbished the Master Cylinder, it would solve everything, and I came across this product, which is a NISSIN product with a separate tank.
Was the one you received as per Image?
I have used a different Master Cylinder diameter on a different car model, so it was as per Image.
Was the installation difficult?
In the case of MT-25, of course, there is no need to consider interference with Cowl, so it is almost a simple installation.
The banjo bolt was left in place, and the brake switch was simply replaced since the terminals are exactly the same.
In my case, I had a hard time getting the air out because I had changed to Separate Handlebars.
How was your experience with it?
The OEM and Piston diameter is the same 11mm and the same sideways push, so we did not feel much change in the touch and effectiveness of the Brake.
However, with Lever's new, crisp and accurate, I feel that my peace of mind has increased many times over.
Also, NISSIN Lever's R condition etc. is so exquisite that my fingers do not get sore at all even if I ride for a long time.
It looks better and Repair Parts are readily available, so there is nothing to say about it.
[Included Parts:were they on?
Basic AlmostQuantity:It is a Set, but the Mirror Holder Bolt for M10Pitch 1.25 does not come with it.
Perhaps the M6 Tank fixed Bolt is a mistake.
It just so happened that the original Mirror Holder cap had the same cap, so I was able to use it and get away with it.
[Was there anything that disappointed you?
Not particularly
【Review】
Quantity:Pair (for Left and Right) It is great to be able to refresh the Master Cylinder for about the price of a Lever set.
Anyway, it is very reliable and has the best Touch of Lever and even Adjuster.
I have graduated from the mysterious Chinese Lever and can now ride without hesitation.
View detail
Fits: HONDA CRM50, HONDA CRM80, HONDA TL125, HONDA TLR200, HONDA TLR250, HONDA XLR125, HONDA XLR200, HONDA XLR250, HONDA XLR80, HONDA CRM250, KAWASAKI KSR110, KAWASAKI KSR50, KAWASAKI KSR80, HONDA XR230, HONDA XR250, HONDA XR250 Motard, HONDA XR400 Motard, HONDA NSR50, HONDA NSR80, HONDA XR100 Motard
I think it's good
The installation itself is easy:remove the OEM and install this Light as is. There was no special modification. The glass surface of the Headlight looks like this, [Color] Now that it is Clear, I think it looks pretty cool. The brightness is not as bright as the OEM light lens, but the light distribution is more variable, and with the LED bulbs, it seems to be bright at a single point. View detail
Easy installation, no brightness problems.
Until now, we had been using Type with LEDs affixed at the top and bottom, but the straightness of the LEDs was poor when Up is lit, so we always used the LEDs facing down.
This type of LEDs are affixed in the LeftRight type, so the straightness when the LEDs are up is also OK. This time, I installed it on a square eye light, but I think it would be best for a round eye light. Finally, I am satisfied with the brightness.
View detail
Exactly to MOTARD as well.
Bought this for my drz400. For a long time, I had been wearing the one for my previous Large Motorcycle, but it was not so good because it was too loose. This time I bought it because it said "for Off-Road" and I am satisfied with the just fit. I also like that the lower part can be closed with a string. View detail
The size is just right and the texture is good.
Used in 2008 YZF-R1.
LengthSize is also really Exactly.
I did not originally intend to use parts cleaner, but I was able to get in without any difficulty without using Bond paint parts cleaner.
View detail
Genuine DID 520ERVT Replacement Chain Link
I always like to have some of these in stock in case of any issue during fitting different chains. The DID 520ERVT is one I do have in stock but have no spares. I found this chain link by just searching through the DID inventory on Webike website. It was really easy to find so you should be just fine. I ordered a few other different chain links along with this as I do like options with spare links. All were shipped together and this saved some shipping cost. My order arrived in 5 days from being shipped. The chain link came in a nice sealed packet with all that is needed to refit. You do get the white grease packet in this size chain so that's always a good thing, I have a lot of these anyway but you cannot have too many. The chain link is very well made one, it also is in the gold colour so nice looking too and it is also embossed with the DID logo so you know it's genuine. I keep the rivet link type and this clip joint type but had ran out of this version, hence the purchase. Very happy with these small purchases and these will keep me going for future. Thank you Webike. View detail
WhiteLight and good looking!
It's super easy because all you have to do is change the Valve.
I was able to purchase Valve's length and fit without concern because of the information provided by its predecessors.
D-TRACKER-X's dark, orange-tinged light has been brightened to white.
I haven't driven at night yet, so I haven't been able to experience the true effect, but the impression of the motorcycle will change considerably just by having white light.
View detail
Bright and low power consumption
I was worried about whether I could install it on my KSR2 since the body is longer, but I saw the impressions of someone who had already installed it on his KSR and he said it could be installed, so I bought it and installed it.
The length was a limit, but I was able to install it, the Others had no problems with the installation, and the rubber cover went on without modification.
The beam coverage has been widened. The optical axis remains the same and is large and sturdy. The high beam illuminates high up and is even brighter, so you have to be careful of oncoming cars.
I also changed the tail lamp to LED, so the power consumption was reduced a lot. I installed the LeftSwitch of the previous model in my car, so I can switch from LightOff to Light when Halogen is on.
Idling dropped about 200 RPM when switched to On, but switching from LightOn to LightOff when LED has no effect on Idling.
View detail
Fits: APRILIA SX50, HONDA NSR80R, KAWASAKI KZ1000 Police, KAWASAKI LeoStar, PEUGEOT Speed Fight 2 WRC, ROYAL ENFIELD Britt 500, ROYAL ENFIELD BritClassic, ROYAL ENFIELD BritClassic Deluxe 535, ROYAL ENFIELD Lightning Custom 535, YAMAHA 125R, APRILIA SR125, APRILIA SR150, APRILIA Mojito Custom 50, BETA EVO 80 JUNIOR, BETA EVO 80 SENIOR, BETA rr 2t 250 enduro, HONDA CRM250, HONDA CRM250R, HONDA CRM50, HONDA CRM80
watchman
For Stock.
It is a standard product and safe.
View detail
Fits: APRILIA SX50, HONDA NSR80R, KAWASAKI KZ1000 Police, KAWASAKI LeoStar, PEUGEOT Speed Fight 2 WRC, ROYAL ENFIELD Britt 500, ROYAL ENFIELD BritClassic, ROYAL ENFIELD BritClassic Deluxe 535, ROYAL ENFIELD Lightning Custom 535, YAMAHA 125R, APRILIA SR125, APRILIA SR150, APRILIA Mojito Custom 50, BETA EVO 80 JUNIOR, BETA EVO 80 SENIOR, BETA rr 2t 250 enduro, HONDA CRM250, HONDA CRM250R, HONDA CRM50, HONDA CRM80
Plug replacement
Regular Plug replacement for CRM. It is a little bit covered. View detail
For CB250F
.Actually this item i could not found in my country (VX Series Joint Link 520VX3). Finally I bought it from webike. It is original. Very good packaging.fast shipping.I am happy to deal with the webike team View detail
I put it on my RG 50Gamma.
It's just like changing a light bulb.
There is no problem
View detail
Changed from Clip to Crimp
When replacing the chain on the KLX230R, the ERVT came with a clip-type joint, but the clip didn't fit well and I had to press-fit it too much and it failed, so I decided to use a Crimp joint, which I am used to.
I think the Crimp is fine for me, and the Crimp is easier to work with because I'm used to it.
View detail