Used for XELVIS No accuracy problems

Used for Honda/XELVIS.
NTB is about 1/3 of the price of OEMSeal which costs about 3,000 yen, but the rubber parts are not so low quality, such as BALI, distortion, etc. They are the parts that will meet your needs to fix the fork oil leak or to refresh the suspension.

However, since the smoothness of Stroke is considered to be the same as that of OEM, there is no performance upgrade, as in the case of SKF, which is famous for Race. The best feature of this product is its cost performance. Also, Dust Seal is the same as Quantity Seal.:Set

As for the installation information, XELVIS had an Inner Tube diameter of 35mm and an Outer inner diameter of 49mm. The length of the pipe should be about 60 cm.

Also, if you are not too careless with your hands, I think it is Large sturdy, but if the seal is facing the wrong way, it will pump up the oil. As shown in the reference photo, the printed side is on the top. You can also tell by the beveled edge on the top side. Please be sure to make a mistake! View detail

1P2014

The head lamp on my Honda Little Cub burned out. I liked the price and parameters of this lamp (not much power does not overheat the cartridge). Everything turned out to be good in quality, the lamp works perfectly. View detail

Anyway, it's bright.

The ADDRESS V100 has a reputation for having a dark headlight to begin with. (1994 model) attached to the
I am impressed that I can now see in front of me when driving at night, but in general, the light intensity is just normal.
Still, it is hard to believe that it is +6.5W, and you can feel the difference between just a light bulb and Halogen very clearly.

We do not yet know how durable it will be, and we do not know if the increased power consumption will affect the battery charge.

Well, even if the Battery goes up, you won't be able to leave because the KICK is on.

Its Risk is unknown, but I think it is worth changing it once for V100Owner who has problems with Headlight.
That's how bright it is! V100 is w View detail

Easy installation, no brightness problems.

Until now, we had been using Type with LEDs affixed at the top and bottom, but the straightness of the LEDs was poor when Up is lit, so we always used the LEDs facing down.
This type of LEDs are affixed in the LeftRight type, so the straightness when the LEDs are up is also OK. This time, I installed it on a square eye light, but I think it would be best for a round eye light. Finally, I am satisfied with the brightness. View detail

Front forkOH of BMW R1100RT

I was searching the Net for a front fork on my R1100RT that was leaking oil and found this one that would fit. OEM is over 3000 yen a piece. View detail

WhiteLight and good looking!

It's super easy because all you have to do is change the Valve.
I was able to purchase Valve's length and fit without concern because of the information provided by its predecessors.
D-TRACKER-X's dark, orange-tinged light has been brightened to white.
I haven't driven at night yet, so I haven't been able to experience the true effect, but the impression of the motorcycle will change considerably just by having white light. View detail

Bright and low power consumption

I was worried about whether I could install it on my KSR2 since the body is longer, but I saw the impressions of someone who had already installed it on his KSR and he said it could be installed, so I bought it and installed it.
The length was a limit, but I was able to install it, the Others had no problems with the installation, and the rubber cover went on without modification.
The beam coverage has been widened. The optical axis remains the same and is large and sturdy. The high beam illuminates high up and is even brighter, so you have to be careful of oncoming cars.
I also changed the tail lamp to LED, so the power consumption was reduced a lot. I installed the LeftSwitch of the previous model in my car, so I can switch from LightOff to Light when Halogen is on.
Idling dropped about 200 RPM when switched to On, but switching from LightOn to LightOff when LED has no effect on Idling. View detail

Does not fit the KL250 Sherpa.

The Manufacturer's list of compatible models says it is compatible with KL250 Sherpa, but that's too long.
If installed normally, there will be excess
The quality of the product itself is not bad, so I think it will be fine for cars with longer forks.

KL250 Sherpa's Fork outerTop to bottom of trident is 240mm
Catalogue value WheelTravel is 230mm
100mm remains above the Outer even when shrunk the most without processing.
This would make Stroke about 130mm.

If it was just for Inner Tube protection purposes, it would be fine, but I don't think it is, so I cut it off, even though it will look very ugly lol.
In hindsight, I lightly regret that using the top half wouldn't have made it so ugly.
However, even in this state, the Stroke will be reduced by about 50mm
Boots itself becomes Bump rubber.

Even other companies' products that say they are compatible with KL250 Sherpa are quite long.
Would it be better to just use a shorter product with more extension?
Maybe I'm losing my mind, but I'd like to find a good product!

I bought it + even processed it so I'll be using it for a while lol. View detail

Genuine DID Spare Chain Link

I was in need of a few spares for various chains I have in stock and this 520 DZ2 was one of those I stock but have no other spare links. I find it is always good to have spares in stock as even though the original chains do come with a link like this, occasionally they do get damaged and then you are stuck. Finding the right chain link was easy as I just checked down Webike's inventory for the one I wanted. The price Webike have these for is brilliant and better than I could source locally. I did order quite a few different types of chain links as I do stock a lot of various chains anyway. As these were all being shipped together, this also saved on a little postage cost. EMS got my order delivered in 5 days from being shipped. This chain link spare came in a nice DID packaging and was well presented. It came with multiple o-rings and a squish pack of white grease. You can never have enough of that anyway. The chain link is very well made as with all DID chains etc. A nice little stock up is what was needed and I am reassured that I now have spares in case I need them. Thanks Webike. View detail

Quantity with high grip tire because it works well.:Set Exchange is a Recommendation

It definitely works better than the OEM Shoe, and the Feel when Brake is applied is good, especially the Rear, which makes me want to use it more aggressively.
Actually, before this DAYTONA made, I replaced the front and rear Brakes of the LITTLE CUB I used to own with Shoe made by a certain company, but the Rear started to squeal after one winter, not even a year had passed. It didn't affect the performance much, but when I was on the street, the Rear started to squeal. "Kikki!" However, the brake squeal stopped after I replaced it with a Daytona brake the summer before last. After that, I rode for a little more than a year without brake squeal.

The SUPER CUB110 is more powerful and heavier than the LITTLE CUB, so you can feel the effect of the SUPER CUB110. (Not as good as HUNTER and other disc brakes, of course.) The fluffy feeling is gone. I also feel that the front end sinks more deeply than the OEM when fully breaking.
Note that before replacing the Tire and Brake Shoe, the Rear sometimes locked up in Panic Breaking, but I think that was due to the OEMTire being poor. (The braking distance is not short because it locks)
After replacing the tires, I tried full breaking on a safe road, and both Front and Rear stopped firmly without locking. The fact that it did not lock up is probably due to the fact that I changed the tires to high grip BS BATTLAX BT-39SS at the same time. I am sure that the brake stops faster and shorter than before the change. I will not recommend this Brake Shoe with OEM Tire because I think it will lock up spectacularly! (Lol)

I have not ridden my JA44 so far, but I have replaced both front and rear with DAYTONA Shoe, so the braking balance is good. View detail

I put it on my RG 50Gamma.

It's just like changing a light bulb.
There is no problem View detail

Anyway, it's a cosmetic!

I don't know about durability, but I chose it for its cosmetic value. View detail

Can't tell the difference between OEM and

I used it to replace the RearShoe on my commuting Motorcycle SUPER CUBja10.
The OEMs that had 21,000 km of use had used the TouchCUBs so close to the limit that the Touch was poor and the effectiveness of the Touch was very weak, but after replacing them with these Shoes, the effectiveness and Touch of the new car was restored. View detail

subtle

Perhaps it is because the Scooter has a low power generation rate, but I feel that the Halogen bulb has a wider beam range and better visibility.
This might be better with a slightly better Halogen bulb. View detail

Headlight LED

Installation was easy. It was brighter than I expected. View detail

To match intake and exhaust system changes

MJ's position was raised due to the air cleaner element and the exhaust air removal Up. View detail

OEM Equivalent Product, cheaper than OEM

Used for LITTLE CUB.
The low beam ran out, and a short time later the high beam also ran out. I bought this one because it was an emergency situation and it was immediately available in stock. The standard is 25-1. The Pine Stripe part number is 1P2015.
The grade of the bulbs is also the same as the OEM, White Hot bulbs, not Halogen.
I also found HalogenType, but the price difference was about three times as much, so I decided to go with the cheaper version.

Replacement is Light rim bottom, Quantity:Pair (for Left and Right) Remove the screw on the Plus of the light rim and lift the light rim upward to remove it.
The Glass part is replaced while touching as little as possible. Time required:2 minutes.
It lit up with no problem. I am relieved. I don't know about the durability yet, but it is a long-established domestic product and I am sure there will be no problem. View detail

Made by DAYTONA

[How is it used?
Used to replace front and rear Drum Brake Shoe,
Because the previous Shoe replacement time was unknown and it was not working well.
How was your experience with it?
When Brake was applied with the same sensation as before the replacement, the Rear brake worked so well that it locked up!
How did it compare to other products?
It may not be as effective as a disc brake, but it is as good as a disc brake, and I am very satisfied with the large size.
[Points to note]
Nothing in particular, but beveling of the shoe, cleaning of the drum brake, and grease up are also required prior to installation.
Brake wires, clutch wires, and other parts were also replaced, both front and rear, but it was not a difficult job, as it was started in the morning and finished before noon.

(I'm giving it 4 stars because I'm not sure how durable it will be.)

Other items that would be helpful
Whether there are Included Parts:/ Items that should be purchased together/Opinions and requests to the Manufacturer View detail

Used on a 50cc 2Cycle moped. Quite bright!

I originally used M&H Mats Stripe Halogen bulb 12V35/30W Clear, which was brighter than OEM, but still old mopeds are still dark.
Since I use them for commuting, I decided to use LEDs for safety reasons.
Installation can be done simply by removing the headlight cowl.
The color is a beautiful White and the brightness feels 1.3 to 1.5 times brighter.
The white color is more like a recent vehicle than the yellow color, which makes it a better parenthesis.
I think it is a good cosmetic product because it is inexpensive and made by Mats Stripe, which is a reliable company!
I use it on my AF35LIVE DIOZX, but the Valve is PH7 because I replaced the Headlight with an external one. View detail

It's brighter than a white-hot bulb.

Installed on a Honda NSR80.
The NORMALWhite heat bulbs in the NSR80 were very dark, so we replaced them with LED bulbs to make nighttime driving somewhat safer.
If anything, it is not for the purpose of illuminating the road surface, I'm here, Appeal." I think it is highly satisfactory if you consider that LEDs for
In NSR80, the heat sink part of the Light case and LED Lamp is the contact limit. There is no problem. View detail