O-ring Size does not fit

VANVAN200
However, the size of the O-ring does not match, even though it is included in the applicable car models.
I need to order OEM to use it. View detail

Matching with Caliper

Purchased a 1/2-inches diameter short lever to replace the front caliper with a Brembo crab caliper.

Piston diameter 32mm in combination with Caliper (hydraulic pressure ratio 6.35) is
No Control at all with stiff Touch.
Piston diameter 34mm in combination with Caliper (hydraulic pressure ratio 7.17) is
Good Controllability, although a little softer than the preferred Touch.

If it were a standard Lever, would the former combination have been acceptable? View detail

Maintenance.

I have not used it yet but the Bolt on the R1 has rusted so I bought it to replace it.
I would recommend everyone to replace it before this happens because it will make the Brake less effective. LOL! View detail

I've only driven about 100km ….

I replaced Red Pad with this one.
I drove about 100 km for now and it works normally.
No wonder.
This may be more suitable than Red Pad, which is more aggressive because it is an off-road vehicle.
It was before, so I don't know much about it. (Sweat) View detail

Directly attached to Ignition coil

As others have said, 250tr has a shorter original IgnitionCable, so I made it the same length and attached it directly.
The cable diameter is thick, so it was installed while shaving it with a cutter as appropriate. This was quite a difficult task.
After installation, I feel a little more power up.
Dress-up can be effective by showing a glimpse of the Yellow-colored Cable. View detail

Replace instead of overhaul 20 year old OEM

The MAJESTY 250 OEM Master Cylinder is 20 years old, the paint is peeling, the fluid level window is white and cloudy, and the touch screen is dead. I thought that if I replaced it with OEM, it would be in the same condition again someday, so I replaced it with this one, which has better accuracy and quality.

The original vehicle had some customization done to the exterior, and the replaced handlebars gave it a more custom look.
I am satisfied that the color of the handlebar matches the color of the MASTER and Lever, creating a sense of unity.

Unlike the OEM, the 6-step lever play adjustment is also highly satisfactory.

Also, we are happy to be able to strengthen the brake with the SKULL Helmet principle by lowering the diameter by 1 Size to 11mm, compared to the OEM MASTERPiston diameter of 1/2-inches.

The brake hoses were stainless steel mesh when they were installed, so we did not have to worry about a large increase in stroke volume, and both control and braking power were improved, resulting in a highly satisfactory brake customization. View detail

Used for MAJESTY 125 FBrakes custom

The MAJESTY125 and R1-Z have the same 83mm Pitch of the front brake caliper, so I used the R1-Z's caliper and changed the front brake to 4POD to strengthen the brake. So, I wanted to lower the Piston size of MASTER, and I wanted to be able to adjust the lever play by Dial as well as CB1300 Caliper, and I wanted to use a short lever. I also wanted to use short lever, so I replaced it with Nisshin's MASTER.

As expected, the brake has improved in both touch and braking power due to the MASTER's smaller-diameter piston size,
Now I have a performance problem on the Caliper side and want to replace the Caliper with the SumitomoCaliper from TZr250 after 3MA or the Nisshin caliper with 83mmPitch released from TZ125, TZ250 and AdvantageNisshin in the 90's. I'm looking for a new caliper. View detail

Titaniumium color!

Small but finely crafted
Luxury that you can feel in your hands
Worth the Gold! View detail

If you don't need O-rings, click here.

I often buy DAYTONA's Perfect set, but when I don't need O-ring, this is cheaper. netShop sells imported very cheap filters, but DAYTONA is not the same as those, and I think the filter paper is well made. View detail

Small

I bought it for my BMW R1150GS because it fits VST 1050, but it is smaller than I expected. I bought it knowing that it would not fit over the SIDEPannier, but I did not expect that it would not fit over the Top case either. The storage is compact. View detail

Used for ESTRELLA

This is a change from NORMAL. The replacement was made in anticipation of aging deterioration.
I can't really feel the difference, but it looks good, so I'm satisfied. View detail

Good product

Fits kawasaki w800 Improved the sponginess feeling Arrived well without any problem with customs Good service Highly recommended View detail

New Master Cylinder while replacing Lever.

[How is it used?
The Yamaha MT-25's Brake lever had been made in China since delivery and I was concerned about rattling.
I was worried about using such a product in Brake, but I was wondering what to do because OEM products are too expensive and other brand products from proper manufacturers are expensive. I was wondering what to do. I realized that if I just refurbished the Master Cylinder, it would solve everything, and I came across this product, which is a NISSIN product with a separate tank.

Was the one you received as per Image?
I have used a different Master Cylinder diameter on a different car model, so it was as per Image.

Was the installation difficult?
In the case of MT-25, of course, there is no need to consider interference with Cowl, so it is almost a simple installation.
The banjo bolt was left in place, and the brake switch was simply replaced since the terminals are exactly the same.
In my case, I had a hard time getting the air out because I had changed to Separate Handlebars.

How was your experience with it?
The OEM and Piston diameter is the same 11mm and the same sideways push, so we did not feel much change in the touch and effectiveness of the Brake.
However, with Lever's new, crisp and accurate, I feel that my peace of mind has increased many times over.
Also, NISSIN Lever's R condition etc. is so exquisite that my fingers do not get sore at all even if I ride for a long time.
It looks better and Repair Parts are readily available, so there is nothing to say about it.

[Included Parts:were they on?
Basic AlmostQuantity:It is a Set, but the Mirror Holder Bolt for M10Pitch 1.25 does not come with it.
Perhaps the M6 Tank fixed Bolt is a mistake.
It just so happened that the original Mirror Holder cap had the same cap, so I was able to use it and get away with it.

[Was there anything that disappointed you?
Not particularly

【Review】
Quantity:Pair (for Left and Right) It is great to be able to refresh the Master Cylinder for about the price of a Lever set.
Anyway, it is very reliable and has the best Touch of Lever and even Adjuster.
I have graduated from the mysterious Chinese Lever and can now ride without hesitation. View detail

Good work.

I am satisfied with no BALI.
O-rings are not attached. View detail

Great product

Product original and match perfect in my motorcycle. The product was well package and arrived well.When I asked the support teams was ready to answer my questions and sent me the invoice fast. View detail

There was no one with Level gauge.

The OEM Product was not strong enough, so it was replaced. After installation, I found that the flange surface is narrower than the OEM Product, so there is a gap between the OEM Product and the engine side. I would have liked to have had a product that fits Exactly. View detail

safety

The product is a Replace product from a well-known manufacturer, and of course, there were no defects.

It is often cheaper than OEM or in stock, so it would be good in that case.

Personally, OEM Product is the best, but Foot Motorcycle uses this one. View detail

Please come once every two times Large body Oil change!

I replaced it at the same time (this is the 3rd time) when replacing the Oil in DL1000 V-STROM250SX.
It seems that about 1 Filter per 2 Oil changes is good. Probably ^^;.
Finally, DL1000 V-STROM250SX is now officially applicable for DL1000 V-STROM250SX, although until recently it was only ridden for JigSar.

At this price, it would be ideal if the Packing system was also included.

The sense of use was naturally worked at the same time as Oil replacement, so you can't tell if it works or not.
We are not going to be able to save this kind of money and have it go bad as a result, so we will be able to make the best use of it.
Replace them regularly. I'm sure it works...I don't know. View detail

It got brighter.

I purchased this because Light was dark.
It brightened up as expected! View detail

Brake Pads for Street Riding

I purchased and installed these Brake Pads for my Ninja 250SL for urban driving (commuting). The cost performance is unquestionably good, but it is still a bit expensive. "Red Pad. Compared to the OEM Brake Pads, the Brake Pads are more controllable and cost-effective, so we recommend these Brake Pads to Mainers who drive in the city. View detail